Analysis of Ah receptor pathway activation by brominated flame retardants

Brominated flame-retardants (BFRs) are used as additives in plastics to decrease the rate of combustion of these materials, leading to greater consumer safety. As the use of plastics has increased, the production and use of flame-retardants has also grown. Many BFRs are persistent and have been detected in environmental samples, raising concerns about the biological/toxicological risk associated with their use. Most BFRs appear to be non-toxic, however there is still some concern that these compounds, or possible contaminants in BFRs mixtures could interact with cellular receptors. In this study we have examined the interaction of decabromodiphenyl ether, Firemaster BP4A (tetrabromobisphenol A), Firemaster PHT4 (tetrabromophthalic anhydride), hexabromobenzene, pentabromotoluene, decabromobiphenyl, Firemaster BP-6 (2,2^′,4,4^′,5,5^′-hexabromobiphenyl) and possible contaminants of BFR mixtures with the Ah receptor. Receptor binding and activation was examined using the Gel Retardation Assay and increased expression of dioxin responsive genes was detected using the reporter gene based CALUX assay. The results demonstrate the ability of BFRs to activate the AhR signal transduction pathway at moderate to high concentrations as assessed using both assays. AhR-dependent activation by BFRs may be due in part to contaminants present in commercial/technical mixtures. This was suggested by our comparative analysis of Firemaster BP-6 versus its primary component 2,2^′,4,4^′,5,5^′-hexabromobiphenyl. Some technical mixtures of brominated flame-retardants contain brominated biphenyls, dioxins or dibenzofurans as contaminants. When tested in the CALUX assay these compounds were found to be equivalent to, or more active than their chlorinated analogues. Relative effective potency values were determined from dose response curves for these brominated HAHs.     

A new method for the rapid determination of volatile organic compound breakthrough times for a sorbent at concentrations relevant to indoor air quality

The use of sorbents has been proposed to remove volatile organic compounds (VOCs) present in ambient air at concentrations in the parts-per-billion (ppb) range, which is typical of indoor air quality applications. Sorbent materials, such as granular activated carbon and molecular sieves, are used to remove VOCs from gas streams in industrial applications, where VOC concentrations are typically in the parts-per-million range. A method for evaluating the VOC removal performance of sorbent materials using toluene concentrations in the ppb range is described. Breakthrough times for toluene at concentrations from 2 to 7500 ppb are presented for a hydrophobic molecular sieve at 25%) relative humidity. By increasing the ratio of challenge gas flow rate to the mass of the sorbent bed and decreasing both the mass of sorbent in the bed and the sorbent particle size, this method reduces the required experimental times by a factor of up to several hundred compared with the proposed American Society of Heating, Refrigerating, and Air-Conditioning Engineers method, ASHRAE 145P, making sorbent performance evaluation for ppb-range VOC removal more convenient. The method can be applied to screen sorbent materials for application in the removal of VOCs from indoor air.     

Impact of engine lubricant properties on regulated gaseous emissions of 2000-2001 model-year gasoline vehicles

The impact of the sulfur (S) content in lubricating oil was evaluated for four ultra-low-emission vehicles and two super-ultra-low-emission vehicles, all with low mileage. The S content in the lube oils ranged from 0.01 to 0.76%, while the S content of the gasoline was fixed at 0.2 ppmw. Vehicles were configured with aged catalysts and tested over the Federal Test Procedure, at idle and at 50-mph cruise conditions. In all testing modes, variations in the S level of the lubricant did not significantly affect the regulated gas-phase tailpipe emissions. In addition to the regulated gas-phase emissions, a key element of the research was measuring the engine-out sulfur dioxide (SO2) in near-real-time. This research used a new methodology based on a differential optical absorption spectrometer (DOAS) to measure SO2 from the lubricants used in this study. With the DOAS, the contribution of SO2 emissions for the highest-S lubricant was found to range from less than 1 to 6 ppm on a gasoline S equivalent basis over the range of vehicles and test cycles used. The development and operation of the DOAS is discussed in this paper.     

Coping with uncertainty: a call for a new science-policy forum

The scientific and policy worlds have different goals, which can lead to different standards for what constitutes "proof" of a change or phenomena, and different approaches for characterizing and conveying uncertainty and risk. These differences can compromise effective communication among scientists, policymakers, and the public, and constrain the types of socially compelling questions scientists are willing to address. In this paper, we review a set of approaches for dealing with uncertainty, and illustrate some of the errors that arise when science and policy fail to coordinate correctly. We offer a set of recommendations, including restructuring of science curricula and establishment of science-policy forums populated by leaders in both arenas, and specifically constituted to address problems of uncertainty.     

Impact of acid mine drainage on benthic communities in streams: the relative roles of substratum vs. aqueous effects

Restoration of streams impacted by acid mine drainage (AMD) focuses on improving water quality, however precipitates of metals on the substrata can remain and adversely affect the benthos. To examine the effects of AMD precipitates independently of aqueous effects, four substrata treatments, clean sandstone, clean limestone, AMD precipitate-coated sandstone and coated limestone, were placed in a circumneutral stream of high water quality for 4 weeks. Iron and Al were the most abundant metals on rocks with AMD precipitate. and significantly decreased after the exposure. Precipitate on the substrata did not significantly affect macroinvertebrate or periphyton density and species composition. In an additional experiment, percent survival of caged live caddisflies was significantly lower when exposed in situ for 5 days in an AMD affected stream than in a reference stream. Caddisfly whole-body concentrations of all combined metals and Fe alone were significantly higher in the AMD stream. Whole-body metal concentrations were higher in killed caddisflies than in live, indicating the importance of passive uptake. The results suggest the aqueous chemical environment of AMD had a greater affect on organisms than a coating of recent AMD precipitate on the substrata (ca. 0.5 mm thick), and treatment that improves water quality in AMD impacted streams has the potential to aid in recovery of the abiotic and biotic benthic environment.     

Ozone dynamics and deposition processes at a deforested site in the Amazon basin

The goal of this study is to investigate the impact of deforestation on ozone dynamics and deposition in the Brazilian Amazon basin. This goal is accomplished through i) analyses of ozone levels and deposition rates at a deforested site during the rainy season; and ii) comparisons of these data with similar information derived at a forest. At the pasture site maximum ozone mixing ratios reach 20 parts per billion on a volume basis (ppbv) but about 6 ppbv prevail over the forest. Maximum ozone deposition velocities for pastures can reach 0.7 cm s-1, which is about threefold lower than values derived for forests. Combining ozone abundance and deposition velocities, pasture maximum ozone fluxes reach approximately 0.2 microgram (ozone) m-2 s-1. This flux represents approximately 70% of the deposition rates measured over the forest. Hence, this study suggests that conversion of rainforests to pastures could lead to a net reduction (30%) in the ozone sink in the Amazon.     

Investigations of nitrogen fluxes and pools on a limestone site in the Alps

In the North Tyrolean Limestone Alps a site was investigated over a four-year period (1998–2001) in order to assess the nitrogen saturation status, the nitrogen budget (quantification of the net uptake of nitrogen by the canopy and of the nitrogen mineralization, nitrogen uptake from roots and N₂O emission rates, proof of the origin of nitrate in the soil water with stable isotope analyses), and the effects of the actual nitrogen input on ground water quality. The main goals were to quantify the nitrogen input rate, the nitrogen pools in above-ground and below-ground compartments, nitrogen turnover processes in the soil as well as the output into the groundwater and into the atmosphere. The findings are based on continuous and discontinuous field measurements as well as on model results.While nitrogen input exceeded the Critical Loads of the WHO (1995), nitrogen deficiency and nutrient imbalances were verified by needle analyses. The atmospheric input of inorganic nitrogen was higher than the nitrogen output in 50 cm soil depth. A tracer experiment with¹⁵N helped to prove that not more than half of the applied nitrate could be discharged. This allows the conclusion that nitrogen is stored in the system and that the site cannot yet be said to be saturated with nitrogen. The same result was also obtained by modelling. In addition, it was proved that the nitrogen discharge did not stem from deposition but from processes within the system.     

Method for the determination of organophosphate insecticides in water, sediment and biota

A procedure for the determination of 13 organophosphate insecticides (OPs) in water, sediment and biota at low ppb levels is described. Samples were extracted with dichloromethane or acetone/hexane and cleaned up with micro-column silica gel chromatography. Measurements were made by dual capillary column gas chromatography using both nitrogen-phosphorus (NPD) and electron capture (ECD) detection. Recoveries from fortified water samples ranged from 76% to 102% for all sample types. Practical detection limits ranged between 0.003 and 0.029 microg/l in natural water samples, 0.0004-0.005 microg/g w.w. for sediments, and 0.001-0.005 microg/g w.w for biota using the NPD and ECD method. Losses in sediments were experienced when sulphur was removed. Precision and accuracy were not affected in sediment samples where sulphur was not removed.     

Migration of saline solutions in variably saturated porous media

Migration of concentrated NaNO3 solutions in homogeneous packs of pre-wetted silica sands was investigated using a light transmission system. Solutions of 5 molal NaNO3 were found to migrate downward 24-62% faster than pure water, in an unstable, fingered manner. This behavior was attributed primarily to a surface tension induced, non-zero apparent contact angle between the imbibing and the resident fluids. For saline solutions of similar surface tension to that of pure water (achieved by the addition of 2% methanol), the migration rates and plume shapes were comparable to that of water, demonstrating that density was not the primary source of the observed differences in migration patterns. At depths where resident saturation increased above residual, the migration process appeared to occur via film flow with slight changes in saturation (<4%), rather than in a series of abrupt jumps, as observed at shallower depths. A method for contact angle scaling was used to illustrate the effects of non-zero contact angles on capillary pressure-saturation curves.     

Porewater chemistry in compacted re-saturated MX-80 bentonite

Bentonites of various types are being investigated in many countries as backfill materials in high-level radioactive waste disposal concepts. Being able to understand the chemistry of the porewater in compacted bentonite is very important since it is critical to predicting radionuclide solubilities and to the synthesis of sorption data bases, and hence to repository safety studies. In this paper, porewater compositions in compacted bentonites are calculated, taking into consideration such factors as montmorillonite swelling, semi-permeable membrane effects, very low "free water" volumes, and the highly effective buffering characteristics of the exchangeable cations and the amphoteric edge sites. The former buffer the cation concentrations and the latter fix the pH in the porewater of a re-saturated bentonite. The above considerations are used in conjunction with previously measured physico-chemical characterisation data on MX-80 powder to calculate porewater compositions in compacted bentonites. For the MX-80 material specified, the porewaters calculated for initial dry densities between 1200 and 1600 kg m(-3) had relatively high ionic strengths (I approximately 0.3 M), similar cation concentrations and a pH equal to 8.0. The porewaters changed from being Na(2)SO(4)-rich at 1200 kg m(-3) to a NaCl/Na(2)SO(4) type water at 1600 kg m(-3).