基于传声器阵列的声源定位技术的应用

基于传声器阵列的声源定位技术中的两个主要方法,STSF和Beamforming声源定位技术两者的实现方法不同。通过对STSF和Beamforming声源定位技术的推导,给出了两种测量技术适用的频率范围和空间范围,从理论上对其应用范围的差异进行了说明,并提出在实际测量中如何选择合适的声源定位方法。结合两种测量技术的特点,提出声源定位技术下一阶段研究的重点。     

三峡库区大宁河沉积物营养盐时空分布及其与叶绿素的相关性分析

为研究大宁河底泥营养盐时空分布与藻细胞分布的关系,本研究在大宁河选择4个代表性的取样点:菜子坝、白水河、双龙和大昌,利用垂直重力采泥器,按照2 cm厚度分层选取底泥,检测底泥中总氮,氨氮、硝态氮、亚硝态氮、总磷、无机磷、有机磷和叶绿素的垂向分布,分析叶绿素与营养盐的相关性.结果表明,菜子坝底泥0.0~2.0 cm总氮浓度最高,白水河底泥2.0~4.0 cm的总氮浓度最高;菜子坝底泥2.0~4.0 cm氨氮浓度最高,1和2月白水河底泥4.0~6.0 cm浓度较高;硝酸氮和亚硝酸氮(除3月)在菜子坝底泥2.0~4.0 cm浓度最高;氨氮、硝酸氮和亚硝酸氮浓度在同一个采样点底泥4.0 cm以下分层差异不显著;白水河底泥总磷0.0~6.0 cm呈增加趋势,菜子坝底泥表层的总磷和无机磷的浓度显著高于其它分层,而且每一分层中总磷、无机磷浓度都高于其他3个取样点相应的分层;有机磷在菜子坝和大昌的浓度高于白水河和双龙的浓度,但是同一采样点底泥不同分层的有机磷浓度差异不显著;同一深层底泥中的叶绿素a浓度在大昌最高,其次是白水河,再次菜子坝,双龙处的叶绿素浓度最低;只有1月在大昌取样点处无机磷和叶绿素a的浓度显著正相关,相关系数为0.87,底泥中的营养盐不是影响底泥藻细胞分布的主要影响因素.     

珠江口夏季有机碳的分布特征及其收支模拟研究

基于三维水质模型对珠江口夏季有机碳的分布特征及其收支进行了研究,量化了各动力学过程对有机碳分布的影响,这对于深入了解珠江口碳循环过程有重要意义.同时,采用2006年7—8月观测数据对模型进行了验证,结果显示模型模拟效果良好.研究表明,珠江口夏季有机碳呈明显的空间变化,其浓度总体上从口门向外海逐步降低,底层递减幅度大于表层;表层平均浓度为2.42 mg·L~(-1),底层平均浓度为1.91 mg·L~(-1).此外,有机碳在垂向上的分布与水体层化紧密相关,层化水域中的有机碳浓度随水深迅速下降,非层化水域上、下层的浓度差异不大.有机碳收支结果则表明,珠江口不同水域有机碳的物理、生化过程差异明显.在内伶仃洋,有机碳分布由物理过程主控,其主要来源与消耗分别为径流输送和沉降,两者分别约占该区域有机碳输入总量的83.80%、83.18%;在中伶仃洋,有机碳分布受物理和生化因素共同调控,其来源以生化产碳为主,动力输送为辅,主要耗碳项为沉降;在外伶仃洋,其西侧水域的有机碳主要来源与消耗分别为径流输送和沉降,有机碳分布受物理和生化过程共同调控,其中,物理过程占优势,而在其东侧水域,有机碳主要来源与消耗分别为生化产碳和生化耗碳,有机碳分布由生化过程主控.另外,捕食产碳和氧化耗碳分别是珠江口各生化过程中最重要的产、耗碳过程.     

The ignored emission of volatile organic compounds from iron ore sinter process

Iron ore sintering is a major source of gaseous and particulate pollutants emission in iron smelt plant. The aim of present study is to characterize the volatile organic compounds(VOCs) emission profiles from iron ore sintering process. Both sinter pot test and sinter simulation experiment were conducted and compared. Out results showed that sinter process produced large quantity of VOCs together with NOxand SO_2. VOCs and NO were produced simultaneously in sinter pot test from 3 to 24 min after ignition, flowed by SO_2 production from 15 min to the end of sintering. Total VOCs(TVOC) concentration in sinter flue gas was affected by the coal and coke ratio in sinter raw material. The maximum TVOC concentration was 34.5 ppm when using 100% coal as fuel. Sinter simulation experiments found that the number of VOCs species and their concentrations were found by sinter temperature. The largest VOCs species varieties were obtained at 500 °C. Benzene, toluene,xylene and ethylbenzene were major VOCs in sinter flue gas based on the results from both simulation test and sinter pot. It thus demonstrated that in addition to NO_x, SO_2 and metal oxide particles, sinter flue gas also contained significant amount of VOCs whose environmental impact cannot be ignored. Based on our work, it is timely needed to establish a new VOC emission standard for sinter flue gas and develop advanced techniques to simultaneously eliminate multi-pollutants in iron ore sinter process.     

Three-dimensional biogenic C-doped Bi2MoO6/In2O3-ZnO Z-scheme heterojunctions derived from a layered precursor

Novel 3D biogenic C-doped Bi_2 MoO_6/In_2O_3-ZnO Z-scheme heterojunctions were synthesized for the first time, using cotton fiber as template. The as-prepared samples showed excellent adsorption and photodegradation performance toward the hazardous antibiotic doxycycline under simulated sunlight irradiation. The morphology, phase composition and in situ carbon doping could be precisely controlled by adjusting processing parameters. The carbon doping in Bi_2 MoO_6/In_2O_3-ZnO was derived from the cotton template, and the carbon content could be varied in the range 0.9–4.4 wt.% via controlling the heat treatment temperature. The sample with Bi_2 MoO_6/In_2O_3-ZnO molar ratio of 1:2 and carbon content of1.1 wt.% exhibited the highest photocatalytic activity toward doxycycline degradation,which was 3.6 and 4.3 times higher than those of pure Bi_2 MoO_6 and Zn In Al-CLDH(calcined layered double hydroxides), respectively. It is believed that the Z-scheme heterojunction with C-doping, the 3D hierarchically micro–meso–macro porous structure, as well as the high adsorption capacity, contributed significantly to the enhanced photocatalytic activity.     

湿地公园对局地气候舒适性影响的数值试验

为探索湿地公园对局地气候舒适性的影响,利用WRF数值模式,对重庆市梁平区待建湿地公园的位置与面积规划进行敏感性试验。结合当地主导风向和实际项目需求,设计了不建设湿地公园、湿地公园占地分别达10 km²、15 km²和20 km²等面积敏感性试验,以及湿地公园位于保护区西南部、东北部和分为南北两部分等建设位置敏感性试验。通过对比不同试验方案下垫面修改前后模拟结果的2 m气温、湿度等气象要素并计算热气候指标,认为湿地公园建设面积约15 km²、且将湿地分为两部分但东北部面积较大时,对当地的局地气候舒适性有较好改善。对风场的分析表明,这可能是因该规划方案能产生新的风道所致,因此也说明湿地公园的规划应当将局地风环境状况作为重要的参考指标。     

中国典型城市PM2.5浓度时空演绎规律及影响因素分析

为探讨空气中ρ（PM_2.5）的空间集聚特征和气候、大气成分变量对空气中ρ（PM_2.5）的影响,利用首批纳入PM_2.5监测的74个城市的ρ（PM_2.5）数据计算Moran's I指数,并选取其中38个典型城市进行计量分析.在基于引力模型的空间权重矩阵基础上,构建面板数据SDM（空间面板杜宾模型）.结果表明:ρ（PM₁₀）、ρ（SO₂）、ρ（CO）、ρ（O₃）、RH（relative humidity,相对湿度）与城市ρ（PM_2.5）呈正相关,而T（temperature,温度）和WS（wind speed,风速）与城市ρ（PM_2.5）呈负相关;ρ（PM₁₀）、ρ（CO）、RH是位于前3位影响城市ρ（PM_2.5）的关键性因素,其总效应分别为0.720 1、0.241 7、0.133 9.地理上邻近城市ρ（PM_2.5）具有明显的外部空间溢出效应,即邻近城市ρ（PM_2.5）每增加10百分点,将导致该地区ρ（PM_2.5）增长6.12百分点.300 km左右是保证PM_2.5区域"联防联控"最佳效果的最大门槛距离,超过该门槛距离,区域"联防联控"的力度和效果会随着距离的增加而逐渐减弱;当门槛距离大于500 km时,ρ（PM_2.5）的空间自相关性不显著.气候变量中,RH和ρ（PM_2.5）呈同方向变化,而T、WS与ρ（PM_2.5）呈反方向变化.研究显示,关注单一地区或单一因素（气候或大气成分）均不能有效控制PM_2.5污染,在保持经济稳定增长的前提下,各地治理PM_2.5应从调整产业结构、优化能源结构、完善防控机制等多个维度共同推进,促使经济增长方式早日从"粗放型"向"集约型"转变.      

内蒙古自治区锡林郭勒盟地震的启示

2004年3月24日9时33分在内蒙古自治区东乌珠穆沁旗与西乌珠穆沁旗间(北纬45.4°,东经118.2°)发生5.9级地震。北京、辽宁朝阳、吉林白城、河北承德地区有感。自治区地震局迅速确定“三要素”,召集紧急会议确定考察队与局留守队,并迅速向灾区了解灾情,向自治区政府报告。同时启动破坏     

江苏省第三产业清洁生产方案的研究

本文通过对第三产业中宾馆饭店、旅游园林、学校等试点单位开展清洁生产的具体措施 ,分析第三产业清洁生产的特点 ,建立第三产业清洁生产的标准规范 ,提出可操作的第三产业实施清洁生产的程序方案 ,探索第三产业发展与环境保护和谐统一的途径     

Incidence rates and risk factors for injury events in high school students in Lijin County, China

PROBLEM: Most investigations of injuries among Chinese populations are focused on urban or better developed areas, fewer on rural or poor areas. METHODS: From September 21 to 27, 2002, an epidemiological investigation of eight kinds of injury-related events was carried out among 1,944 students in 39 classes randomly sampled from middle schools in Lijin County, a rural area. The eight kinds of events were: (a) traffic accidents, (b) poisoning, (c) fall, (d) burn or scald, (e) blunt or sharp tools contact, (f) electrical contact, (g) animal or insect bites, and (h) non-fatal drowning. RESULTS: The total incidence rate of eight kinds of injuries in the previous year was 21.1%. The incidence rate among boys was 24.2%, while that among girls was 17.4%, which was significant (chi-square=13.4, P<0.05). The incidence rate among junior high school students was 23.1%, while that among senior high school students was 15.5%, which was also significant (chi-square=13.2, P<0.05). A case-control study of 410 students with at least one of eight kinds of injury events indicated that students' gender and their mothers' health status were related to their injuries. CONCLUSION: The injury incidence rate in a rural area was less than other results in urban or developed areas. Students' gender and mothers' health status were important factors associated with the occurrence of injury. IMPACT ON INDUSTRY: In order to improve the surroundings of the growing population of adolescents, some preventive measures should be put forward, especially to the high-risk students of injury.