中国原油进口来源国供应安全的定量评估

原油供给安全在中国国家安全中占有重要地位,对其定量评估可为防范风险提供政策参考。采用事件数据分析法定量测度中国与21个主要原油进口来源国之间的双边关系,结果表明：中国与大多数原油贸易伙伴的关系处于中低水平,但近十多年总体保持上升趋势,原油进口存在一定的政治关系风险但趋于下降。选用资源、政治、经济、运输、军事5个方面的11个指标,通过组合赋权法确定指标权重,运用集对分析方法评估中国21个原油进口来源国的供应安全度,并识别主要障碍因子。结果表明：21国供应安全度存在较大差异。部分中东国家、俄罗斯、委内瑞拉、哈萨克斯坦供应安全度较高,多数非洲国家和亚太国家供应安全度较低。供应国的原油资源状况、运输风险、政治风险是制约多数国家供应安全的主要障碍因素。为防范风险,中国需坚持开展多边“能源外交”,扩大战略石油储备等多方面施策方针。     

东南亚生物质燃烧输送影响我国西南气溶胶辐射特性研究

利用2013年地基CE-318太阳光度计观测数据,结合中分辨率成像光谱仪（MODIS）遥感产品和HYSPLIT后向轨迹分析,研究了一次东南亚生物质燃烧污染长距离输送至中国西南昆明站点过程（2013年4月5~8日）中,气溶胶光学特性和辐射特性的变化及其可能来源.结果表明,此次污染过程期间,我国西南地区生物质燃烧活动较少,而中南半岛地区生物质燃烧活动显著.4月5~7日,昆明站点气溶胶光学厚度（AOD）升高,消光波长指数（EAE）和吸收波长指数（AAE）均增大.此外,依据EAE和AAE分类方法,5~6日昆明站点以城市工业气溶胶为主,7~8日以生物质燃烧气溶胶为主,其细模态峰值半径（0.11μm）小于5~6日（0.15μm）,7日细模态粒子体积浓度峰值（约为0.16μm³/μm²）是5日的2倍.气溶胶直接辐射强迫（ARF）日变化结果表明4月7日气溶胶对地表的降温效应达到最大,对大气的加热作用最强.气溶胶直接辐射强迫效率值（ARFE）的变化表明生物质燃烧气溶胶对大气顶的降温作用减弱.MODIS遥感以及HYSPLIT模式后向轨迹表明,此次昆明站点生物质燃烧气溶胶主要来源于东南亚地区（主要是印度北部、印缅北部和不丹地区）.     

有机废物厌氧发酵生物合成己酸研究进展

厌氧发酵处理有机废物并合成高价值羧酸盐的技术日趋成熟。尤其是己酸作为产物之一,因其附加值高,易于分离,用途广泛,越来越受到关注。微生物合成己酸需要电子供体及受体。详细介绍了乙醇、乙酸分别作为电子供体、受体合成己酸的机理——逆β氧化反应,总结合成己酸底物以及影响合成的因素（温度、pH值、水力停留时间、竞争路径、氢气分压、底物比例、氮源等）。目前采用科氏梭菌以乙醇为电子供体来合成己酸的技术较成熟,探索了利用乳酸为电子供体合成己酸的代谢机理,并指出开发乳酸转化合成己酸的技术可成为未来发展方向。     

含水层介质中1株异养硝化-好氧反硝化菌的分离鉴定与脱氮性能

从受氮污染浅层含水层介质中分离纯化得到1株高效异养硝化-好氧反硝化细菌XK51,经过菌落形态、生理生化特性及16S rDNA基因序列分析,鉴定该菌株为假单胞菌属恶臭假单胞菌(Pseudomonas Putida)。脱氮性能结果表明:XK51为兼性反硝化细菌,能在好氧或缺厌氧条件下高效反硝化脱氮,最大和平均反硝化速率分别为27.3,4.4 mg/(L·h),硝酸盐脱除率为95.3%;该菌株同时具有较高异养硝化能力,最大和平均硝化速率分别为4.2,1.4 mg/(L·h),氨氮脱除率为98.5%。XK51最佳碳源为柠檬酸三钠,适宜生长温度为28~35 ℃,最适温度为30 ℃;适宜生长pH为6.5~8.0,最适pH为7.0。XK51可同时进行异养硝化及同步硝化-反硝化,培养期间未出现明显亚硝酸盐和硝酸盐累积,在含氮污废水处理和地下水氮污染修复方面具有潜在工程应用价值。     

新型厌氧多级喷动床及其厌氧氨氧化脱氮性能分析

为改善厌氧反应器内的流态,加快污泥的颗粒化和形成具有生态梯度的微生物生态系统,设计并制作了新型厌氧多级喷动床,实验测试了反应器的水力喷动、气体喷涌和污泥分层分级现象。在常温下,利用新型厌氧多级喷动床接种混合污泥,经过42 d的培养,成功启动厌氧氨氧化反应器,稳定运行18 d后,NH₄+-N、NO₂--N去除率均达到90%以上。启动60 d后,反应器底部出现大量粒径2 mm左右的颗粒污泥,且污泥具有良好的稳定性和沉降性能,沉降速度达到70 m/h。结果表明:厌氧多级喷动床因其特殊的水力结构,可有效加快污泥的颗粒化。     

Aerosol optical properties under different pollution levels in the Pearl River Delta (PRD) region of China

To clarify the aerosol hygroscopic growth and optical properties of the Pearl River Delta(PRD)region,integrated observations were conducted in Heshan City of Guangdong Province from October 19 to November 17,2014.The concentrations and chemical compositions of PM_(2.5),aerosol optical properties and meteorological parameters were measured.The mean value of PM_(2.5) increased from less than 35(excellent) to 35-75 μg/m~3(good) and then to greater than 75 μg/m~3(pollution),corresponding to mean PM_(2.5) values of 24.9,51.2,and 93.3 μg/m~3,respectively.The aerosol scattering hygroscopic growth factor(f(RH = 80%)) values were 2.0,2.12,and 2.18 for the excellent,good,and pollution levels,respectively.The atmospheric extinction coefficient(σext)and the absorption coefficient of aerosols(σ_(ap)) increased,and the single scattering albedo(SSA)decreased from the excellent to the pollution levels.For different air mass sources,under excellent and good levels,the land air mass from northern Heshan had lower f(RH) and σ_(sp) values.In addition,the mixed aerosol from the sea and coastal cities had lower f(RH) and showed that the local sources of coastal cities have higher scattering characteristics in pollution periods.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.     

UV/H2O2 oxidation of tri(2-chloroethyl) phosphate: Intermediate products, degradation pathway and toxicity evaluation

Tri(2-chloroethyl) phosphate (TCEP) with the initial concentration of 5 mg/L was degraded by UV/H₂O₂ oxidation process. The removal rate of TCEP in the UV/H₂O₂ system was 89.1% with the production of Cl^? and PO₄^3? of 0.23 and 0.64 mg/L. The removal rate of total organic carbon of the reaction was 48.8% and the pH reached 3.3 after the reaction. The oxidative degradation process of TCEP in the UV/H₂O₂ system obeyed the first order kinetic reaction with the apparent rate constant of 0.0025 min^?1 (R²=0.9788). The intermediate products were isolated and identified by gas chromatography-mass spectrometer. The addition reaction of HO? and H₂O and the oxidation reaction with H₂O₂ were found during the degradation pathway of 5 mg/L TCEP in the UV/H₂O₂ system. For the first time, environment risk was estimated via the “ecological structure activity relationships” program and acute and chronic toxicity changes of intermediate products were pointed out. The luminescence inhibition rate of photobacterium was used to evaluate the acute toxicity of intermediate products. The results showed that the toxicity of the intermediate products increased with the increase of reaction time, which may be due to the production of chlorine compounds. Some measures should be introduced to the UV/H₂O₂ system to remove the highly toxic Cl-containing compounds, such as a nanofiltration or reverse osmosis unit.     

Photodegradation of Hexafluoropropylene Oxide Trimer Acid under UV Irradiation

As a novel alternative to traditional perfluoroalkyl substances (PFASs), including perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), hexafluoroproplyene oxide trimer acid (HFPO-TA) has been detected worldwide in surface water. Moreover, recent researches have demonstrated that HFPO-TA has stronger bioaccumulation potential and higher hepatotoxicity than PFOA. To treat these contaminants e.g. PFOA and PFOS, some photochemical techniques by adding exogenous substances had been reported. However, there is still no report for the behavior of HFPO-TA itself under direct UV irradiation. The current study investigated the photo-transformation of HFPO-TA under UV irradiation in aqueous solution. After 72 hr photoreaction, 75% degradation ratio and 25% defluorination ratio were achieved under ambient condition. Reducing active species, i.e., hydrated electrons and active hydrogen atoms, generated from water splitting played dominant roles in degradation of HFPO-TA, which was confirmed by different effects of reaction atmospheres and quenching experiments. A possible degradation pathway was proposed based on the products identification and theoretical calculations. In general, HFPO-TA would be transformed into shorter-chain PFASs, including hexafluoropropylene oxide dimer acid (HFPO-DA), perfluoropropionic acid (PFA) and trifluoroacetate (TFA). This research provides basic information for HFPO-TA photodegradation process and is essential to develop novel remediation techniques for HFPO-TA and other alternatives with similar structures.