Chromium redox speciation in natural waters

Dissolved hexavalent chromium concentrations were determined in river, estuarine and coastal waters of the Humber catchment in north-east England. Samples were collected, filtered, extracted on site and after storage for up to eight days. Hexavalent chromium concentrations did not change by more than 0.05 microg l(-1) (not significant, p = 0.05) over this period. Total chromium concentrations in the catchment were less than 1.0 microg l(-1). This is low in relation to the proposed Environmental Quality Standard. Hexavalent chromium accounted for between 27% and 100% of the total dissolved concentration, with an average of approximately 50%. The proportion of Cr(III) and Cr(VI) in the rivers and estuary were of the same range as previously measured in 1993. The addition of Cr(III) and Cr(VI) to fresh and saline water samples illustrates the complexity of the factors controlling chromium speciation in natural waters. The presence of oxidisable organic matter and the stabilising role of complexing organic ligands are proposed as the main controlling influences of redox speciation in filtered samples.     

Persistent chlorinated pesticides in fish and cattle fat and their implications for human serum concentrations from the Sene-Gambian region

The concentrations of organochlorine pesticides (OCPs) in fish, shrimps, cattle fat and human serum samples from the Sene-Gambian region were measured using validated analytical methodologies. The results obtained were compared with those of other existing African studies and with data from other developing countries. In fish samples, p,p'-dichlorodiphenyldichloroethylene (p,p'-DDE) and HCB were detected with a frequency of 100%, whereas p,p'-dichlorodiphenyltrichloroethane (p,p'-DDT) was detected in eight, heptachlorepoxide in six and endosulfansulfate in five of the nine fish samples. Relatively low concentrations of OCPs were found in cattle and shrimp fat samples. p,p'-DDE and alpha-hexachlorocyclohexane (alpha-HCH) were the most frequently identified. The sum of HCHs ranged from undetected to 13.3 ng g-1 fat, the sum of DDTs from 11.1 to 199.2 ng g-1 fat and the sum of endosulfans from not detected to 49.7 ng g-1 fat in fish and shrimps. In serum samples, alpha-HCH, p,p'-DDE, o,p'-DDT and p,p'-DDT were detected in all 16 pooled serum samples, whereas endosulfansulfate, methoxychlor, mirex, heptachlorepoxide and endrin were detected in 15 samples with most of the concentrations below 10 ng mL-1. The concentrations of OCPs in human serum were given on a serum lipid and whole serum volume basis. The implications for the human diet of these OCP concentrations in serum were investigated by means of biomagnification factors related to the log Kow values of the targeted compounds. The current use of HCH mixtures was suggested to explain the unusually high alpha-HCH concentration. The distribution pattern of these OCPs in humans was also discussed and compared with that in other studies.     

Fate and movement of atrazine, cyanazine, metolachlor and selected degradation products in water resources of the deep Loess Hills of Southwestern Iowa, USA

The environmental fate and movement of herbicides widely used for weed control in corn are assessed for a deep loess soil in southwestern Iowa. Beginning in the early 1980s, the herbicide-based weed control program emphasized the application of atrazine (ATR) or cyanazine (CYN) and metolachlor (MET) for both broadleaf and grass control. Between 1992 and 1995, concentrations of ATR, desethylatrazine (DEA), desisopropylatrazine (DIA), CYN and MET were measured in rainwater, both shallow and deep vadose zone water, and well water. Results show that the frequency of herbicide detections and the range and distribution of occurrences are dependent upon both landscape position and temporal inputs of recharge water from rainfall. Generally, DIA was observed more frequently and in higher mean concentration in well water than DEA, while DEA was observed more frequently than DIA in vadose zone groundwater. A chromatographic analogy is suggested to explain the occurrence patterns observed for both parent herbicide and degradation products within the unsaturated zone water. Analysis of rainwater samples collected during this time also revealed low concentrations of ATR, CYN and MET, with the timing of the detections indicative of non-local transport. Results show that the deep loess soil conducts both water and agricultural chemicals relatively rapidly and as such represents a production system which is vulnerable to contamination of shallow groundwater by herbicide-derived chemicals. Results also illustrate the importance of including major herbicide degradation products in water resource impact assessment studies.     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).     

Using environmental stressor information to predict the ecological status of Maryland non-tidal streams as measured by biological indicators

In Maryland, U.S., an interim framework has recentlybeen developed for using biologically based thresholds, or `biocriteria', to assess the health of nontidal streams statewide at watershed scales. The evaluation of impairment is based on indices of biological integrity from the Maryland Biological Stream Survey (MBSS). We applied logistic regression to quantify how the biotic integrity of streams at a local scale is affected by cumulative effects resulting from catchment land uses, point sources, and nearby transmission line rights-of-way. Indicators for land use were developed from the remote sensing National Land Cover Data and applied at different scales. We determined that the risk of local impairment in nontidal streams rapidly increases with increased urban land use in the catchment area. The average likelihood of failing biocriteria doubled with every 10% points increment in urban land, thus an increase in urban land use from 0 to 20% quadruples the risk of impairment. For the basins evaluated in this study, catchments with more than 40–50% urban land use had greater than 80% probability of failing biocriteria, on average. Inclusion of rights-of-way and point sources in the model did not significantly improve the fit for this data set, most likely because of their low numbers. The overall results indicate that our predictive modeling approach can help pinpoint stream ecosystems experiencing or vulnerable to degradation.     

Biotreatability and kinetics of UASB reactor to mixtures of chlorophenol pollutants

In most natural ecosystems heterotrophic microorganisms encountercomplex mixtures of carbon sources, each of which is present at aconcentration of few micrograms per litre. This study examined the biotreatability and kinetics of an upflow anaerobic sludge blanket (UASB) reactor to complex mixtures of chlorophenols encountered in environmental conditions using on-line and off-line experimental studies. Results indicate that (1) steady-state concentration was quite lower (98.3 mg L^-1) with complex mixture of chlorophenols than steady-state concentration achieved when only 2.4 dichlorophenol (124 mg L^-1) was studied alone on the same reactor; (2) that toxiceffects of chlorophenols increase with increasing concentrationsof toxicant. (Onset of the inhibitory effect occurred at a lowerconcentration in multi-substrate than in single substrate utilization); (3) addition of alternative utilizable substrate can mitigate toxic effects and enhance degradation; (4) the relative concentration of substrate was critical in determiningutilization patterns. HPLC analysis of off-line experimental samples resulted in a steady-state treatment efficiency of68% for COD, 36% for 2-hlorophenol, 40.5% for 4-chlorophenol, 70.7% for 2,4-dichlorophenol, 53.2% for 2,4,6-trichlorophenol and 42% for pentachlorophenol in presence of glucose. Kinetic constant in terms of V _max and K _s were determined. K _s for the five chlorophenols ranged between 0.016 and 0.117 kg m^-3 day^-1 while V _max ranged between 0.056 and 0.244 kg m^-3 day^-1.     

Evaluation of interference to conventional and real-time PCR for detection and quantification of fungi in dust

Advances in polymerase chain reaction (PCR) have permitted accurate, rapid and quantitative identification of microorganisms in pure cultures regardless of viability or culturability. In this study, a simple sample processing method was investigated for rapid identification and quantification of fungal spores from dust samples using both conventional and real-time PCR. The proposed method was evaluated for susceptibility to interference from environmental dust samples. Stachybotrys chartarum and Aspergillus fumigatus were used as test organisms. The sensitivity of detection in pure culture was 0.1 spore DNA equivalents per PCR reaction corresponding to 20 spores ml(-1) in the sample. However, 1 spore DNA equivalent per PCR reaction corresponding to 200 spores ml(-1) in the sample was the lowest amount of spores tested without interference in dust samples spiked with spores of either fungal species. The extent of inhibition was calculated using conventional and real-time PCR reactions containing fungal spores, specific primers, specific probes (for real-time PCR) and various amounts of dust. The results indicate that the extent of inhibition by dust on PCR varies with the type and amount of dust, and number of spores. No interference in the analysis of spiked samples was detected from 0.2 mg ml(-1) of four real-life dust samples at p-value >0.05 using 2 x 10(4) spores for conventional PCR and 2 x 10(5) spores for real-time PCR. However, samples containing >0.2 mg ml(-1) real-life dust compromised the PCR assay. These results suggest the potential usefulness of a simple sample processing method in conjunction with PCR for monitoring the fungal content of aerosols collected from indoor environments.     

Spatial contaminant heterogeneity: quantification with scale of measurement at contrasting sites

Material within the terrestrial environment is rarely homogeneously distributed, either spatially or temporally. One consequence of heterogeneity is that uncertainty is usually generated in measurements that are taken with the aim of characterising the environment. For example, a measurement of analyte concentration within soil taken from one sampling location on contaminated land can vary substantially when compared against another sample taken at effectively the same nominal location. The measurement uncertainty arising from the heterogeneity can substantially limit the reliability of the interpretations made upon environmental investigations. The sampling uncertainty usually outweighs the analytical uncertainty from the laboratory, often by a factor of 20 or more. One approach to reducing the uncertainty is to design a more suitable sampling strategy. This might be achieved by predicting the degree of heterogeneity prior to the investigation, but this is often difficult to achieve accurately. Another approach, which was investigated here, is to actually characterise the heterogeneity prior to the main investigation using rapid and inexpensive technology, such as in situ measurement techniques. In situ portable X-ray fluorescence (PXRF) and X-ray microprobe (XMP) techniques were employed to test the feasibility of this approach. Two contrasting contaminated land sites were chosen to characterise the two-dimensional spatial heterogeneity of heavy metal contamination in topsoil at a range of scales (50 m to 0.001 m). The spatial heterogeneity of contaminants, expressed as relative standard deviations, was found to differ between the two sites by a factor of two, largely due to the mode of deposition of pollution. The study also indicated that the heterogeneity did not change systematically with the scale of measurement between sampling locations at either site.     

Pool of Dust Particles over the Asian Continent: Balloon-borne Optical Particle Counter and Ground-based Lidar Measurements at Dunhuang, China

Measurements of aerosols were made in 2001 and 2002 at Dunhuang (40 degrees 00'N, 94 degrees 30'E), China to understand the nature of atmospheric particles over the desert areas in the Asian continent. Balloon-borne measurements with an optical particle counter suggested that particle size and concentration had noticeable peaks in super micron size range not only in the boundary mixing layer but also in the free troposphere. Super-micron particle concentration largely decreased in the mid tropopause (from 5 to 10 km; above sea level, a.s.l.). Lidar measurements made during August 2002 at Dunhuang suggested the possibility that mixing of dust particles occurred from near the ground to about 6 km even under calm weather conditions, and a large depolarization ratio of particulate matter was found in the aerosol layer. The top of the aerosol layer was found at heights of nearly 6 km (a.s.l.). It is strongly suggested that nonspherical dust particles (Kosa particles) frequently diffused in the free atmosphere over the Taklamakan desert through small-scale turbulences and are possible sources of dust particles of weak Kosa events that have been identified in the free troposphere not only in spring but also in summer over Japanese archipelago. Electron microscopic experiments of the particles collected in the free troposphere confirmed that coarse and nonspherical particles observed by the mineral particle were major components of coarse mode (diameter larger than 1 microm) below about 5 km over Dunhuang, China.     

Total versus inhalable sampler comparison study for the determination of asphalt fume exposures within the road paving industry

Exposure to asphalt fumes has a threshold limit value (TLV of 0.5 mg m(-3) (benzene extractable inhalable particulate) as recommended by the American Conference of Governmental Industrial Hygienists (ACGIH). This reflects a recent change (2000) whereby two variables are different from the previous recommendation. First is a 10-fold reduction in quantity from 5 mg m(-3) to 0.5 mg m(-3). Secondly, the new TLV specifies the "inhalable" fraction as compared to what is presumed to be total particulate. To assess the impact of these changes, this study compares the differences between measurements of paving asphalt fume exposure in the field using an "inhalable" instrument versus the historically used 'total' sampler. Particle size is also examined to assist in the understanding of the aerodynamic collection differences as related to asphalt fumes and confounders. Results show that when exposures are limited to asphalt fumes, a 1:1 relationship exists between samplers, showing no statistically significant differences in benzene soluble matter (BSM). This means that for the asphalt fume ACGIH TLV, the 'total' 37-mm sampler is an equivalent method to the "inhalable" method, referred to as IOM (Institute of Occupational Medicine), and should be acceptable for use against the TLV. However, the study found that when confounders (dust or old asphalt millings) are present in the workplace, there can be significant differences between the two samplers' reported exposure. The ratio of IOM/Total was 1.37 for milling asphalt sites, 1.41 for asphalt paving over granular base, and 1.02 for asphalt over asphalt pavements.