臭氧对枯草芽孢杆菌孢子的灭活研究

隐孢子虫灭活困难,给饮用水安全带来了挑战。实验以枯草芽孢杆菌孢子(ATCC6633)作为隐孢子虫的指示菌,研究了臭氧浓度、浊度、有机物、温度等因素对臭氧灭活枯草芽孢杆菌孢子的影响。研究表明,臭氧对枯草芽孢杆菌孢子的灭活与CT值相关,臭氧浓度对消毒效果影响较小;降低浊度、有机物含量,能提高臭氧对枯草芽孢杆菌孢子的灭活效率;温度降低,为保证一定的消毒效率,所需的CT值越大。研究结果为水厂合理控制运行参数提供了借鉴。     

高压脉冲电凝-Fenton-生化法处理制药废水

通过高压脉冲电凝-Fenton对制药废水进行预处理,出水进入UASB-AO生化处理系统.研究表明:高压脉冲电凝-Fenton氧化法的最佳工况条件为进水pH值为4.0左右,高压脉冲电凝反应时间为45 min,H2O2投加量为4mL/L,Fenton氧化时间为60min.高压脉冲电凝-Fenton对CODCr去除率为36.5%～39.2%,ρ(BOD5)/ρ(CODCr)从0.13提高到0.32-0.34,废水的可生化性大大提高,UASB厌氧反应器去除率为81.4%～82.1%,AO系统去除率为88.0%～88.5%,而整个生化处理系统对CODCr去除率为95.4%～97.9%,最终出水各项指标可达到GB 8978-1996<污水综合排放标准>中一级标准.     

好氧颗粒污泥处理青霉素废水研究

青霉素在其生产过中产生大量的废水,其COD值较高,生化性较差,成分复杂,微生物难以降解,其处理技术是世界性难题。文章采用以葡萄糖模拟废水培养的好氧颗粒污泥为接种体,经青霉素废水逐步驯化后,使其完全处理青霉素废水。实验结果表明,应用好氧颗粒污泥技术,处理青霉素废水,COD,NH3_N,TP去除率较高,具有很好的处理效果。     

有机改性膨润土在印染废水处理中的应用

膨润土是一种非常有用的非金属矿物原料,其有机改性得到的有机改性膨润土可以较好地去除印染废水中的有机污染物和色度。本文综述了有机改性膨润土的制备方法及其在印染废水处理中的应用现状。     

Debromination of decabromodiphenyl ether by organo-montmorillonite-supported nanoscale zero-valent iron：Preparation, characterization and influence factors

An organo-montmorillonite-supported nanoscale zero-valent iron material(M-NZVI) was synthesized to degrade decabromodiphenyl ether(BDE-209). The results showed that nanoscale zero-valent iron had good dispersion on organo-montmorillonite and was present as a core-shell structure with a particle size range of nanoscale iron between 30–90 nm, characterized by XRD, SEM, TEM, XRF, ICP-AES, and XPS. The results of the degradation of BDE-209 by M-NZVI showed that the efficiency of M-NZVI in removing BDE-209 was much higher than that of NZVI. The efficiency of M-NZVI in removing BDE-209 decreased as the pH and the initial dissolved oxygen content of the reaction solution increased, but increased as the proportion of water in the reaction solution increased.     

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium nanoparticles

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium （Pd） nanoparticles was studied for the first time. The effects of Pd loading, dye concentration and reuse repetitions of membranes were investigated. In reduction, the dye concentration decreased whereas the pH rose gradually. An optimal Pd loading was found. The catalytic membranes were able to be reused more than 3 times.     

Comparison of quartz sand, anthracite, shale and biological ceramsite for adsorptive removal of phosphorus from aqueous solution

The choice of substrates with high phosphorus adsorption capacity is vital for sustainable phosphorus removal from waste water in constructed wetlands. In this study, four substrates were used： quartz sand, anthracite, shale and biological ceramsite. These substrate samples were characterized by X- ray diffractometry and scanning electron microscopy studies for their mineral components （chemical components） and surface characteristics. The dynamic experimental results revealed the following ranking order for total phosphorus （TP） removal efficiency： anthracite 〉 biological ceramsite 〉 shale 〉 quartz sand. The adsorptive removal capacities for TP using anthracite, biological ceramsite, shale and quartz sand were 85.87, 81.44, 59.65, and 55.98 mg/kg, respectively. Phosphorus desorption was also studied to analyze the substrates＇ adsorption efficiency in wastewater treatment as well as the substrates＇ ability to be reused for treatment. It was noted that the removal performance for the different forms of phosphorus was dependent on the nature of the substrate and the adsorption mechanism. A comparative analysis showed that the removal of particulate phosphorus was much easier using shale. Whereas anthracite had the highest soluble reactive phosphorus （SRP） adsorptive capacity, biological ceramsite had the highest dissolved organic phosphorus （DOP） removal capacity. Phosphorus removal by shale and biological ceramsite was mainly through chemical adsorption, precipitation or biological adsorption. On the other hand, phosphorus removal through physical adsorption （electrostatic attraction or ion exchange） was dominant in anthracite and quartz sand.     

Carbonyl emissions from heavy-duty diesel vehicle exhaust in China and the contribution to ozone formation potential

Fifteen heavy-duty diesel vehicles were tested on chassis dynamometer by using typical heavy duty driving cycle and fuel economy cycle. The air from the exhaust was sampled by 2,4- dinitrophenyhydrazine cartridge and 23 carbonyl compounds were analyzed by high performance liquid chromatography. The average emission factor of carbonyls was 97.2 mg/km, higher than that of light-duty diesel vehicles and gasoline-powered vehicles. Formaldehyde, acetaldehyde, acetone and propionaidehyde were the species with the highest emission factors. Main influencing factors for carbonyl emissions were vehicle type, average speed and regulated emission standard, and the impact of vehicle loading was not evident in this study. National emission of carbonyls from diesel vehicles exhaust was calculated for China, 2011, based on both vehicle miles traveled and fuel consumption. Carbonyl emission of diesel vehicle was estimated to be 45.8 Gg, and was comparable to gasolinepowered vehicles （58.4 Gg）. The emissions of formaldehyde, acetaldehyde and acetone were 12.6, 6.9, 3.8 Gg, respectively. The ozone formation potential of carbonyls from diesel vehicles exhaust was 537 mg O3/km, higher than 497 mg O3/km of none-methane hydrocarbons emitted from diesel vehicles.     

Review of the progress in preparing nano Ti02： An important environmental engineering material

TiO2 nanomaterial is promising with its high potential and outstanding performance in photocatalytic environmental applications, such as CO2 conversion, water treatment, and air quality control. For many of these applications, the particle size, crystal structure and phase, porosity, and surface area influence the activity of TiO2 dramatically. TiO2 nanomaterials with special structures and morphologies, such as nanospheres, nanowires, nanotubes, nanorods, and nanoflowers are thus synthesized due to their desired characteristics. With an emphasis on the different morphologies of TiO2 and the influence factors in the synthesis, this review summarizes fourteen TiO2 preparation methods, such as the sol-gel method, solvothermal method, and reverse micelle method. The TiO2 formation mechanisms, the advantages and disadvantages of the preparation methods, and the photocatalytic environmental application examples are proposed as well.     

电子受体类型对聚磷污泥胞外聚合物的影响研究

采用3种电子受体(硝氮、亚硝氮、氧),在SBR反应器中分别驯化了具有稳定除磷能力的聚磷污泥。对比研究了不同聚磷污泥胞外聚合物(EPS)的组分与含量,结合三维荧光光谱对EPS中有机物质进行分析。研究表明,以硝氮、亚硝氮为电子受体的聚磷污泥EPS平均浓度较为接近,分别为115.6mg/gVSS、133.5 mg/gVSS,由厌氧段至缺氧段,EPS总浓度有所下降。以氧为电子受体聚磷污泥的EPS平均浓度相对较高,为194.5 mg/gVSS,由厌氧段至好氧段,EPS总浓度略有升高。不同聚磷污泥的EPS组分均以胞外蛋白为主,占EPS总量的53%~65%,多糖与核酸占EPS总量28%~34%、5%~7%。三维荧光光谱显示3种聚磷污泥EPS均具有芳香结构蛋白质、可溶性代谢物的荧光峰,另外,以硝氮为电子受体的聚磷污泥还具有明显的腐殖酸类物质的荧光峰。研究结果表明电子受体对聚磷污泥EPS的组分、浓度、有机质类别有一定的影响。