Photodegradation of alachlor with the TiO(2) film immobilised on the glass tube in aqueous solution

Alachlor photodegradation was performed using TiO(2), which was synthesized by a modified sol-gel method. The thickness of a TiO(2) film immobilised by a 5-time dip-coating was 174 nm and the average diameter of TiO(2) particles was about 10-15 nm in SEM images. The crystal structure of a TiO(2) film calcinated at 300 degrees C for 1 h was observed as a typical anatase type. The stability of a TiO(2) film by a modified sol-gel method was 4% better than TiO(2) by a typical sol-gel method.The removal rate of alachlor with both Fe(3+) and UV radiation in the absence of TiO(2) was 0.28 mg/l/h in 10 h and the removal rate of alachlor with Fe(3+)/UV in the presence of TiO(2) was 0.32 g/l/h, which was higher by 14% than that with Fe(3+)/UV system. TOC concentration during the alachlor degradation with both TiO(2) and UV radiation in the absence of added Fe(3+) decreased from 100%, through 81% and 51%, to 44% with time elapses of 4, 8, and 10 h, respectively, while TOC concentration with both added Fe(3+) and UV radiation in the absence of TiO(2) decreased from 100% to 70% in 10 h.     

CuCl2-catalyzed PCDD/F formation and congener patterns from phenols

Homologue and isomer patterns of polychlorinated dibenzo-p-dioxin (PCDD) and polychlorinated dibenzofuran (PCDF) in CuCl2-catalyzed formation were studied in an isothermal flow reactor using a distribution of 20 phenols as measured in municipal waste incinerator (MWI) exhaust gases. A mixture of 20 phenols was synthesized and used as reactants for this study because phenols are known to be key precursors in the formation of PCDD/F. Experiments were conducted at 400 degrees C. The 92% of nitrogen (N2) and 8% of oxygen (O2) were used as a carrier gas. PCDD/F homologue and isomer patterns with dibenzo-p-dioxin (DD) and dibenzofuran (DF) were obtained from a mixture of 20 phenols. DF+PCDF formation was favored over DD+PCDD formation. The major homologue groups formed were non-chlorinated DD and DF, and PCDD/F homologue fraction decreased with the degree of chlorination. PCDD/F homologue and isomer distributions were almost constant. Phenol and lower chlorinated phenols present in high amount played an important role in PCDD/F congener distributions. The results presented here can be used as characteristics or fingerprints for homologue and isomer patterns of PCDD/F formation attribution in CuCl2-catalyzed reaction from phenols.     

Chlorination of dibenzofuran and dibenzo-p-dioxin vapor by copper (II) chloride

Dibenzofuran (DF) is formed from phenol and benzene in combustion gas exhaust streams prior to particle collection equipment. Subsequent chlorination at lower temperatures on particle surfaces is a potential source of chlorinated dibenzofuran (CDF). Gas streams containing 8% O₂ and approximately 0.1% DF vapor were passed through particle beds containing copper (II) chloride (0.5% Cu, mass) at temperatures ranging from 200 to 400 °C to investigate the potential for CDF formation during particle collection. Experiment duration was sufficient to provide an excess amount of DF (DF/Cu=3). The efficiency of DF chlorination by CuCl₂ and the distribution of CDF products were measured, with effects of temperature, gas velocity, and experiment duration assessed. Results of a more limited investigation of dibenzo-p-dioxin (DD) chlorination by CuCl₂ to form chlorinated DD (CDD) products are also presented.The efficiency of DF/DD chlorination by CuCl₂ was high, both in terms of CuCl₂ utilization and DF/DD conversion. Total yields of Cl on CDF/CDD products of up to 0.5 mole Cl per mole CuCl₂ were observed between 200 and 300 °C; this suggests that nearly 100% CuCl₂ was utilized, assuming a conversion of two moles of CuCl₂ to CuCl per mole Cl added to DD/DF. In a short duration experiment (DF/Cu=0.3), nearly 100% DF adsorption and conversion to CDF was achieved. The degree of CDF chlorination was strongly dependent on gas velocity. At high gas velocity, corresponding to a gas–particle contact time of 0.3 s, mono-CDF (MCDF) yield was largest, with yields decreasing with increasing CDF chlorination. At low gas velocity, corresponding to a gas–particle contact time of 5 s, octa-CDF yield was largest. DF/DD chlorination was strongly favored at lateral sites, with the predominant CDF/CDD isomers within each homologue group those containing Cl substituents at only the 2,3,7,8 positions. At the higher temperatures and lower gas velocities studied, however, broader isomer distributions, particularly of the less CDD/CDF products, were observed, likely due to preferential destruction of the 2,3,7,8 congeners.     

Characteristics of Ion Components and Trace Elements of Fine Particles at Gosan, Korea in Spring time from 2001 to 2002

Size-segregated measurements of the composition of an aerosol are used to determine the transport of natural and anthropogenic aerosols to the Gosan site in springtime from 2001 to 2002. Although the transport of Asian dust is a well-known phenomenon in springtime, this study shows that not only is soil dust transported into Gosan each spring but so are anthropogenic aerosols, including sulfur, enriched trace metals such as Pb, Zn, Ni, K, S. This study also combines the size- and time-resolved aerosol composition measurements with isentropic, backward air-mass trajectories in order to identify some potential source regions of the anthropogenic aerosols. Finally, four types of transport episodes were identified: (1) anthropogenic pollutants, (2) dust storm mixed with the anthropogenic aerosols, (3) typical dust storms, (4) some sea salt with clean air mass. Overall, in addition to typical soil dust, a large amount of anthropogenic aerosols, whether mixed with the soil dust or not, are transported to Gosan each spring.     

Effect of Solids Concentration on Bacterial Leaching of Heavy Metals from Sewage Sludge

Abstract

Microbial metal leaching from sewage sludge (2-9% w/v) was carried out with the iron-oxidizing bacterium Thiobacillus ferrooxidans. Measurements of pH, oxidation-reduction potential, and concentration of Fe²⁺ indicated that T. ferrooxidans was effective in removing metals from an incubation bath containing less than 5% sludge solids concentration. Specifically, Cu leaching was completely suppressed at a high solids concentration of 9% (w/v). Results indicated that the deactivation of T. ferrooxidans at a high sludge content was mainly due to the presence of inhibiting materials such as organic matter. A mixed culture of sulfur-oxidizing bacteria was obtained by enrichment from anaerobically digested sewage sludge to enhance the efficiency of the microbial leaching process. These bacteria were much more effective in metal leaching than was iron-oxidizing T. ferrooxidans. At 9% (w/v) solids concentration, the leaching efficiencies of Zn and Cu were 78% (2.66 g/kg dry sludge) and 59% (1.36 g/kg dry sludge), respectively. Therefore, when removing heavy metals from the anaerobically digested sewage sludge, the indigenous sulfur-oxidizing bacteria isolated in the current study were more efficient than T. ferrooxidans, especially at high sludge solids concentrations.     

Installation of platform screen doors and their impact on indoor air quality: Seoul subway trains

In this study, variations of particulate matter (PM) concentrations in subway trains following installation of platform screen doors (PSDs) in the Seoul subway system were investigated. PM samples were collected in the trains on subway lines 1–8 before and after installation of PSDs. It was found that the mean PM₁₀ concentration in the trains after PSDs installation increased significantly by 29.9% compared to that before installation. In particular, the increase of PM₁₀ in line 6 was the highest at 103%. When the relationship between PM₁₀ and PM_2.5 was compared, coefficients of determination (r²) before and after PSDs installations were 0.696 and 0.169, respectively. This suggests that air mixing between the platform and the tunnel after PSDs installation was extremely restricted. In addition, the indoor/outdoor PM₁₀ ratio following PSDs installation increased from 1.32 to 2.97 relative to the period with no installed PSDs. Furthermore, this study revealed that PM levels in subway trains increased significantly after all underground PSDs were put in use. Several potential factors were examined that could result in this PM increase, such as train ventilation systems, operational conditions, passenger volume, subway depth, and the length of underground segments.

ImplicationsPM₁₀ concentrations inside the subway trains increased after PSDs installation. This indicates that air quality in trains was very seriously impacted by PSDs. PM₁₀ levels were also influenced by the tunnel depth and length of the underground segments. To prevent the adverse effect on human health by PM₁₀ emitted from the tunnel, an applicable ventilation system to reduce PM₁₀ is required inside trains and tunnels.     

Assessment of wood pellet combustion in a domestic stove

Wood pellet is a densified fuel with homogeneous physical properties suitable for use at various scales in domestic and industrial furnaces. A wood pellet stove is a small-scale furnace for domestic heat production that can replace conventional oil or gas boilers. Since the fuel properties of wood pellet are very different from those of oil or gas, the design of a wood pellet stove requires profound understanding of solid fuel combustion as well as of gas flow mixing and reactions. Due to limitations on the height of an installed furnace (~1 m), poor design of the furnace, air supply, fume extraction, or the heat exchanger may lead to excessive CO emissions or low energy efficiency. This study evaluated the design of an existing wood pellet stove with 30,000 kcal/h capacity, using experimental and computational techniques in order to optimize the furnace design. The results show that it is critical to minimize unused furnace volume and to enhance gaseous mixing for reduced CO emissions while maintaining sufficiently high temperatures for fast oxidation.     

Environmental risk assessment of genetically engineered herbicide-tolerant Zoysia japonica

Herbicide-tolerant Zoysia grass (Zoysia japonica Steud.) has been generated previously through Agrobacterium tumefaciens-mediated transformation. The genetically modified (GM) Zoysia grass survived Basta spraying and grew to maturity normally while the wild-type (WT) grass stopped growing and died. GM Zoysia grass will permit more efficient weed control for various turf grass plantings such as home lawns, golf courses, and parks. We examined the environmental/biodiversity risks of herbicide-tolerant GM Zoysia before applying to regulatory agencies for approval for commercial release. The GM and WT Zoysia grass' substantial trait equivalence, ability to cross-pollinate, and gene flow in confined and unconfined test fields were selectively analyzed for environmental/biodiversity effects. No difference between GM and WT Zoysia grass in substantial traits was found. To assess the potential for cross-pollination and gene flow, a non-selective herbicide, Basta, was used. Results showed that unintended cross-pollination with and gene flow from GM Zoysia grass were not detected in neighboring weed species examined, but were observed in WT Zoysia grass (on average, 6% at proximity, 1.2% at a distance of 0.5 m and 0.12% at a radius of 3 m, and 0% at distances over 3 m). On the basis of these initial studies, we conclude that the GM Zoysia grass generated in our laboratory and tested in the Nam Jeju County field does not appear to pose a significant risk when cultivated outside of test fields.     

Arsenic speciation and accumulation in evapoconcentrating waters of agricultural evaporation basins

To sustain agricultural productivity, evaporation basins (or ponds) have been widely used for the disposal of agricultural drainage in areas requiring subsurface drainage in the San Joaquin Valley of California, USA. The drainage water contains elevated concentration of trace elements including selenium (Se) and arsenic (As). Unlike Se, little information is available about As, a potentially high risk element. The objective of this study was to characterize the chemical behavior of As and acquire data for better understanding of biogeochemical processes and conditions affecting As fate in evaporation ponds. The study site was a 726 ha evaporation basin facility (containing 10 cells with water flowing in series) in the hydrologically closed Tulare Basin of California. We examined water chemistry, As concentration and speciation along the water flow path between cells as well as within the cells. Arsenic concentrations in the water increased linearly with Cl(-), a conservative ion from evapoconcentration. Reduced As species as arsenite [As(III)] and organic arsenic (org-As) also increased with increases in Cl(-) and salinity. Water samples with elevated EC (i.e., towards the end of flow path) had high dissolved organic matter, low dissolved oxygen, and elevated sulfide concentrations, indicating the development of reducing conditions. We hypothesize that such changes could facilitate the reduction of arsenate [As(V)] to As(III) and org-As. Elevated As in sediment profiles indicate a solid phase sink mechanism, but not significant enough to remove and reduce As concentrations in the water columns. These findings help us better define the processes that affect As in drainage facilities and contribute to our understanding of how As behaves in other regions of the world that have similar climatic and hydrogeochemical conditions.