Aerobic treatment of palm oil mill effluent

In this study treatment of palm oil mill effluent (POME) was investigated using aerobic oxidation based on an activated sludge process. The effects of sludge volume index, scum index and mixed liquor suspended solids during the acclimatizing phase and biomass build-up phase were investigated in order to ascertain the reactor stability. The efficiency of the activated sludge process was evaluated by treating anaerobically digested and diluted raw POME obtained from Golden Hope Plantations, Malaysia. The treatment of POME was carried out at a fixed biomass concentration of 3900+/-200mg/L, whereas the corresponding sludge volume index was found to be around 105+/-5mL/g. The initial studies on the efficiency of the activated sludge reactor were carried out using diluted raw POME for varying the hydraulic retention time, viz: 18, 24, 30 and 36h and influent COD concentration, viz: 1000, 2000, 3000, 4000 and 5000mg/L, respectively. The results showed that at the end of 36h of hydraulic retention time for the above said influent COD, the COD removal efficiencies were found to be 83%, 72%, 64%, 54% and 42% whereas at 24h hydraulic retention time they were 57%, 45%, 38%, 30% and 27%, respectively. The effectiveness of aerobic oxidation was also compared between anaerobically digested and diluted raw POME having corresponding CODs of 3908 and 3925mg/L, for varying hydraulic retention time, viz: 18, 24, 30, 36, 42, 48, 54 and 60h. The dissolved oxygen concentration and pH in the activated sludge reactor were found to be 1.8-2.2mg/L and 7-8.5, respectively. The scum index was found to rise from 0.5% to 1.9% during the acclimatizing phase and biomass build-up phase.     

Statistical apportionment and risk assessment of selected metals in sediments from Rawal Lake (Pakistan)

The present study was carried out in order to evaluate the statistical apportionment and risk assessment of selected metals (Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Pb, Sr, and Zn) in freshly deposited sediments in Rawal Lake, Pakistan. Composite sediment samples were collected, oven-dried, grounded, homogenized, and processed to assess the water-soluble and acid extractable concentrations of the metals in the water extract and acid extract of the sediments using flame atomic absorption spectrophotometer. Statistical methods were used to identify the possible sources of the metals. Sediment quality guidelines and potential acute toxicity were used to evaluate the ecotoxicological sense of selected metals. Non-carcinogenic health risk assessment was also carried out to determine the potential adverse health risks to the inhabitants. Relatively higher concentration was noted for Ca, Fe, Mg, Na, K, Mn, and Sr in the sediment samples. Principal component analysis and cluster analysis revealed anthropogenic contributions of Cd, Pb, Cr, Mn, Fe, and Li in the sediments. Enrichment factors of the metals in sediments showed severe to moderate enrichment of Cd, Pb, Ca, Fe, Li, Mn, and Sr. Geoaccumulation indices and contamination factors evidenced significant contamination by Cd and Pb, although, on the whole, low degree of contamination was noted. The levels of some metals exceeded the sediment quality guidelines, which revealed frequently adverse biological effects to the dwelling biota in the aquatic ecosystem. The sediments were found to be significantly contaminated by Cd, Pb, Cr, Mn, Fe, and Li.     

Development and characterization of cell line from the gill tissue of Catla catla (Hamilton, 1822) for toxicological studies

Catla gill cell line (ICG) was established from gill tissue of Indian major carp (Catla catla), a freshwater fish cultivated in India. The cell line was maintained in Leibovitz’s L-15 supplemented with 10% fetal bovine serum. These cells have been sub-cultured more than 55 passages over a period of 2 years. The ICG cell line consists predominantly of epithelial-like cells. The cells were able to grow at a wide range of temperatures from 24 °C to 32 °C with an optimum temperature of 28 °C. The growth rate of gill cells increased as the fetal bovine serum (FBS) proportion increased from 2% to 20% at 28 °C with optimum growth at the concentrations of 10% or 15% FBS. Amplification of mitochondrial gene 12s rRNA using primers specific to C. catla confirmed the origin of this cell line from C. catla. The cells were successfully cryopreserved and revived at passage numbers 25, 35, 45 and 55. The cytotoxicity of three metal salts (ZnCl₂, CuSO₄ and CdCl₂) was assessed in ICG cell line using multiple endpoints such as MTT, Neutral Red assay, Alamar Blue assay and Coomassie Blue protein assay. Acute toxicity assay on fish were conducted by exposing C. catla for 96 h to three metal salts under static conditions. Statistical analysis revealed good correlation with r² = 0.908–0.985 for all combinations between endpoints employed. Linear correlations between each in vitro EC₅₀ and the in vivo LC₅₀ data were highly significant.     

Optical and Chemical Methods of Metal Ash Analysis and Tin Recovery

‘Metal ash’ presents a waste disposal problem in most of the developing countries as the industries employ obsolete technologies. In this paper we describe analysis of tin ash, zinc ash and aluminium ash by means of optical methods, such as X-ray diffraction (XRD), inductively coupled plasma mass spectrometry (ICP-MS), electron probe micro analysis (EPMA), scanning electron microscopy (SEM) and chemical methods. The results of tin ash obtained by XRD method matched well with the cassiterite, a naturally occurring mineral of tin. ICP-MS studies reveal the presence of a large number of tracer metals, which may cause pollution by tertiary dispersion and this aspect is discussed. Conversely, the data generated by chemical methods are limited. However, the methods are simple and cost-effective. Then, they can easily be adopted by low-budget industries. Simple and cost-effective process to recover tin from tin ash is described. It is based on heating tin ash with sodium cyanide to about 900°C to separate tin component from the metal ash. The process recovers good quality tin and offers a very high yield. The process can be scaled up to small pilot plant.     

An investigation of ergonomics analysis tools used in industry in the identification of work-related musculoskeletal disorders.

Web-based surveys were sent to Canadian certified ergonomists, Joint Health and Safety Committees (JHSCs) and health and safety certification trainers to understand better which ergonomics analysis tools were used in industry and help JHSCs obtain the necessary training required to reduce work-related musculoskeletal disorders (WMSDs). The results showed that most of the certified ergonomists used the Snook/Mital tables, the National Institute of Occupational Safety and Health (NIOSH) equation and rapid upper limb assessment (RULA) /rapid entire body assessment (REBA). The most frequently used methods by JHSCs to identify ergonomics risk were injury reports and worker complaints. The surveys for the health and safety certification trainers revealed that most curricula did not include ergonomics analysis tools. There appears to be a gap between what is recommended by certified ergonomists for JHSC, what is taught in training and what is used by JHSCs for ergonomics risk analysis. A better understanding, modifications in training curricula and education of JHSCs are needed to help reduce WMSDs.     

The potential of cost-effective coconut husk for the removal of toxic metal ions for environmental protection

Coconut (Cocos nucifera) husk, an agricultural waste, has been thoroughly investigated for the removal of toxic Cd(II), Cr(III) and Hg(II) ions from aqueous media. The parameters like nature and composition of electrolyte, concentration of toxic ions, dosage of coconut husk, and equilibration time between the two phases were optimized for their maximum accumulation onto the solid surface. The effect of common ions on the uptake of metal ions has been monitored under optimal conditions. The variation of retention of each metal ion with temperature was used to compute the thermodynamic quantities DeltaH, DeltaS and DeltaG. The values 18.1+/-0.6 kJmol(-1), 74+/-2 Jmol(-1)K(-1), and -3.8+/-0.04 kJmol(-1) at 298 K; 10.8+/-0.8 kJmol(-1), 48.8+/-2.7 Jmol(-1)K(-1), and -4.6+/-0.3 kJmol(-1) at 298 K; and -37.4+/-2k Jmol(-1), 105+/-7 Jmol(-1)K(-1) and -2.58+/-0.5 kJmol(-1) at 298 K were obtained for Cd(II), Cr(III) and Hg(II) ions, respectively. The sorption data were analysed by applying different sorption isotherms. The sorption capacity and energy were evaluated for each metal ion. The values of the Freundlich constants 1/n and C(m) were 0.92+/-0.04 and 52.6+/-22.2 mmolg(-1); 0.85+/-0.05 and 56.0+/-0.03 mmolg(-1); and 0.88+/-0.03 and 6.84+/-0.45 mmolg(-1) for Cd(II) Cr(III) and Hg(II) ions, respectively. Similarly, the Dubinin-Radushkevich (D-R) constants beta, X(m,) and E were evaluated for the three metal ions. To check the selectivity of the sorbent, sorption of a number of elements was measured under similar conditions. Separation of Zn(II) from Cd(II); Cr(III) from I(I), Zr(IV), Se(IV), and Hg(II) from Se(IV) and Zn(II) can be achieved using this sorbent. This cheap material has potential applications in analytical chemistry, water decontamination, industrial effluent treatment and in pollution abatement.