Utilization of a fumigated sediment by two benthic deposit-feeders:Abra alba (Mollusca: Bivalvia) andEupolymnia nebulosa (Annelida: Polychaeta)

The present study tested the utilization of dead microbial biomass by two benthic deposit-feeders:Abra alba (Wood) (Mollusca: Bivalvia) andEupolymnia nebulosa (Montagu) (Annelida: Polychaeta). Clams were collected in the Canet lagoon during spring 1989. Worms were collected in the Port-Vendres harbour during spring 1989. The¹⁴C-labelled (glutamic acid, 24 h) sediment used during the study was sterilized with 1% chloroform, washed with sterile seawater, and dried (60°C; 48 h). This sterilisation procedure, called fumigation is the least harmful to the sediment (Novitsky 1986). Both clams and worms were incubated in the presence of the fumigated sediment for 5, 10, 20, and 50 h. At the end of each experiment we recorded the radioactivity in four compartments: (1) sediment, (2) dissolved organic matter (DOM), (3) CO₂, and (4) animals. The radioactivity of the sediment was subdivided into five fractions: (i) soluble in 2N HCl, (ii) soluble in hot 5% trichloroacetic acid (TCA), (iii) soluble in 1N NaOH, (iv) soluble in hot 6N HCl, (v) residual (after combustion in a Leco carbon analyser). In the first set of experiments, after 20 h of incubation, 5.4 and 4.7% of the total radioactivity was taken up by clams and worms, respectively. However, a model revealed that this uptake could have been correlated with the release of radiolabelled DOM (33% of total radioactivity during the first 5 h). In order to test this assumption, we used the same protocol with three additional washes of the fumigated sediment. This resulted in a significantly lower uptake by the clams (1.9% of the total radioactivity byt = 50 h), whereas the worms exhibited an uptake similar to that in the initial experiment (5.1% of total radioactivity byt = 50 h). These results underline the importance of considering interactions with DOM when applying radiotracer techniques to the study of benthic food chains. The average ingestion rates of fumigated sediment byA. alba andE. nebulosa were 5.2 10^–2 mg sediment dry wt mg^–1 clam h^–1 and 3.5 10^–2 mg sediment dry wt mg^–1 worm h^–1, respectively, which is comparable to previous data reported for other deposit-feeding bivalves and polychaetes feeding on natural sediment or detritus. The low radioactivity recorded for CO₂ together with the similarity of the changes in the partitioning of the radioactivity within the sediment between control experiments and experiments carried out in the presence of clams or worms suggest low assimilation efficiencies. Therefore, the present study supports the fact that dead microbial biomass does not constitute an important food source for benthic deposit-feeders.     

Effects of elevated CO2 concentration on the polyamine levels of field-grown soybean at three O3 regimes

Effects of increased ozone (O3) and carbon dioxide (CO2) on polyamine levels were determined in soybean (Glycine max L. Merr. cv. Clark) grown in open-top field chambers. The chamber treatments consisted of three O3 regimes equal to charcoal filtered (CF), non-filtered (NF), and non-filtered plus 40 nl litre(-1) O3 and CO2 treatments equal to 350, 400 and 500 microl litre(-1) for a total of nine treatments. Leaf samples were taken at three different times during the growing season. Examination of growth and physiological characteristics, such as photosynthesis, stomatal resistance, and shoot weight, revealed that increasing CO2 ameliorated the deleterious effects of increased O3. Results from the initial harvest, at the pre-flowering growth stage (23 days of treatment), showed that increasing O3 at ambient CO2 caused increases in putrescine (Put) and spermidine (Spd) of up to six-fold. These effects were lessened with increased CO2. Elevated CO2 increased polyamines in plants treated with CF air, but had no effect in the presence of ambient or enhanced O3 levels. Leaves harvested during peak flowering (37 days of treatment) showed O3-induced increases in Put and Spd at ambient CO2 concentrations. However, increased CO2 levels inhibited this response by blocking the O3-induced polyamine increase. Leaves harvested during the pod fill stage (57 days of treatment) showed no significant O3 or CO2 effects on polyamine levels. Our results demonstrate that current ambient O3 levels induce the accumulation of Put and Spd early in the growing season and that further increases in O3 could result in even greater polyamine increases. These results are consistent with a possible antiozonant function for polyamines. The ability of increased CO2 to protect soybeans from O3 damage, however, does not appear to involve polyamine accumulation.     

The influence of acidic mine and spoil drainage on water quality in the mid-Wales area

The many abandoned base metal mines of the mid-Wales ore field are sources of extensive pollution. Some of the mineralised veins contain large amounts of pyrite and marcasite and oxidative weathering of these produces sulphuric acid resulting in very acidic mine drainage waters. In addition, the spoil tips associated with these mines can contain abundant iron sulphides. Drainage waters from these sources have pH values as low as 2.6 and are heavily contaminated with metals such as Al, Zn, Cd and Ni.Two of the main rivers of the area, the Rheidol and Ystwyth, intercept heavily contaminated acidic drainage which has a marked effect on water quality. The Rheidol contains over 100 g L^–1 Zn for 16 km downstream of the acid water influx. This level is over three times the recommended EEC limit for Zn in salmonoid waters of low hardness.     

Low frequency of extra-pair paternity in pied flycatchers revealed by DNA fingerprinting

Summary Genetic parentage of 135 nestlings from 27 broods of polygynous and monogamous pied flycatchers Ficedula hypoleuca was analyzed by means of multilocus DNA fingerprinting. The minisatellite probe alpha-globin 3HVR detected approximately 12 scorable bands per fingerprint, and the proportion of bands shared between presumably unrelated adults averaged 0.22+0.08 SD. The fingerprints of 125 of the 135 nestlings made a complete match to those of their putative parents. In 4 nestlings a single mismatched band occurred, but since band sharing with both putative parents was high, the single mismatches were assumed to be caused by mutation. The 6 remaining nestlings had 5 or more mismatched bands each, low band-sharing proportions with their putative father and high band-sharing proportions with their putative mother. We thus conclude that they were all sired through extra-pair copulations (EPCs). Hence, only 4% of nestlings were sired through EPCs, and none resulted from intraspecific brood parasitism. One of the cuckolding males was identified, explaining all 5 mismatched bands in the nestling's fingerprint. Three of the illegitimate nestlings were from primary nests of polygynous males; 3 were from nests of monogamous males. The fact that many males in this study started to advertise for a second female in a distant territory several days before their first mate began egglaying, and still managed to secure almost exclusive paternity in their first brood, suggests that male polyterritoriality is not costly in terms of lost paternity. Common anti-cuckoddry tactics performed by male birds, like high rate of within-pair copulation and continuous mate-guarding thoughout the female's fertilizable period, do not seem to be important in pied flycatchers.Offprint requests to: J.T. Lifjeld     

Impact of repeated application on the binding and persistence of [14C]-DDT and [14C]-HCH in a tropical soil

An Indian sandy loam soil was initially treated with 1 kg a.i. ha(-1) of either [(14)C]-p,p'-DDT or [(14)C]-gamma-HCH during winter. DDT concentration after 30 days declined to 75.3%, which included 2.1% soil-bound residues. After 150 days, DDT levels further decreased to 42.4% with a concomitant increase in bound residues amounting to 5.9%. Identical treatment with HCH caused the residue levels to be reduced to 67.4 and 23.6%, after 30 and 150 days, respectively. During this period, the soil-bound residues of HCH increased from 5.2 to 12.8%. Repeat application to pre-treated soils in summer and subsequent field exposure for 30 days reduced the concentration of DDT to 52.1% and that of HCH to 42.4% of the total concentration following the second treatment. In parallel control experiments, which received only a single treatment, DDT levels declined to 61.3%, while HCH slumped to 45.3%, indicating a slower dissipation rate than in the corresponding repeated treatments. In repeat experiments, the soil-bound residues of DDT and HCH showed only a 1.07 to 1.08-fold increase in 30 days, as compared to three to ten-times increase in the control experiments. The results amply demonstrate that pre-treatment of tropical soils with DDT or HCH enhances their rate of dissipation and significantly reduce the formation of their soil-bound residues.     

The influence of pH on cadmium toxicity to the green alga Stichococcus bacillaris and on the cadmium forms present in the culture medium

Cadmium toxicity to the green alga Stichococcus bacillaris was investigated in media of pH 3-9. A significant decrease of cadmium toxicity occurred in both the acidic and alkaline ranges of pH. In media of pH 3 and 9, cadmium did not affect the dry mass content substantially. Maximum toxicity of cadmium was noticed at pH 6-7. Voltametric investigations showed a significant effect of pH on electrochemically measured cadmium content in the culture media. Hydrolysis of the medium components and formation of cadmium complexes with OH(-) ions caused a considerable decrease in amounts of electrochemically measured cadmium in the alkaline range of pH.     

Air Pollution in Singapore: Its Multielemental Aspect as Measured by Nuclear Analytical Techniques

Aerosol samples were collected in 1994 in Singapore on two occasions: once in June during the normal meteorological conditions and later in October during a long haze period caused by the heavy forest fire in Indonesia. Filtration and impaction collection methods were used simultaneously so that detailed elemental analysis of bulk as well as of different size fractions could be performed. Accelerator based nuclear analytical techniques such as Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and Nuclear Microscopy (NM) were used for analysis. These techniques are fast, truly multielemental and perfectly suited for routine analysis of a large number of aerosol samples. Typically all samples were analysed for the following 24 elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Mn, Cr, Fe, Co, Ni, Cu, Zn, Ga, As, Br, Rb, Sr and Pb. Detection limits for bulk analysis were generally below ng/m3 and for single particle analysis absolute detectable mass was approximately 10-17 g. Additionally, trace elements such as Cd, Sn, Sb and Ba whose characteristic X-ray lines were normally "obscured" by the lines of other more abundant elements, were detected when analysing by nuclear microscope in single particle mode.Judging by the average concentrations of lead and sulphur which are good indicators of industrial component of air pollution the situation in Singapore is satisfactory. Pb was typically found in concentrations of 5 to 50 ng/m3 and sulphur in concentrations of 1 to 2 µg/m3. These concentrations are well below limits set by the World Health Organisation (1500 ng/m3 and 40 µg/m3, respectively). On the other hand during the haze period the average concentrations of elements like S, K, Ti, V, Mn, Ni, As and Pb were found to be 3 to 6 times higher than usual. Results are presented and discussed.     

Development of monitoring technology for airborne particulate matter

Particulate matter suspended in the air has adverse effects onhuman health. Its level of concentration is an important parameter in evaluating the degree of hazard it poses to the atmosphere. Conventional methods used in measuring particulatematter are often filter-based, which indicates some disadvantagesbecause such a base requires labor and time. In this study, to achieve real-time measurements, a new electrical method was developed for measuring PM10 and PM2.5 concentrations. The basicprinciple is to electrically charge particles passing through thePM inlet using a corona charger and measure the currents createdby charged particles to obtain the number concentration of particulate matter. A new type inlet based on the particle cupimpactor configuration was designed and its performance was evaluated. A unipolar diffusion charger was developed and thecharger's efficiency was determined experimentally in terms ofPn, which represents the penetration through the charger,P, times the average charge number acquired by a particle,n, for different particle sizes. The correlation was constructed between the PM10 (or the PM2.5) mass concentrationsand the electrical currents due to particles, which were chargedby the diffusion charger.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

State estimation in wastewater engineering: Application to an anaerobic process

The use of an extended Kalman filter for state estimation in biological wastewater treatment processes is discussed. The application of the technique requires an adequate mechanistic dynamic model and the identification and modelling of the major sources of stochastic disturbances in the process. The filter allows the on-line tracking of process variables which are not directly measurable. The use of an extended Kalman filter is illustrated through a simulated application to a high rate anaerobic wastewater treatment process.