Analyses of PAHs (polycyclic aromatic hydrocarbons) and mutagenicity in raw and chlorinated water

Both raw water and chlorinated drinking water samples were collected from and the Liu‐Du water treatment plant in northern Taiwan from October 1990 to April 1992. The polycyclic aromatic hydrocarbons (PAHs) and mutagenicity in these water samples were analyzed by GC/MS and Ames test. The Mutagenicity/DMSO (Dimethyl Sulfoxide) ratio in S. typhimurium TA98 and TA100 with or without S9 mixture increased, even higher than 2, following the sequence of unit process. It was observed that the mutagenicity with TA98 (S9+) was highly related to most of PAHs in the raw water; while the mutagenicity with TA98 (S9+) was only correlated with DbA and BghiPr in the treated water. It could be expected that the mutagenicity level was controlled by other predominant components after the raw water was treated, for example, the chlorination process.     

Determination of chemical characterizations of activated carbons from various raw materials

The objectives of this research were to identify the surface chemical features of activated carbons made of peat, bituminous coal and coconut shell, as well as examine the specific relationship of these properties by using statistical analyses. The results showed that the peat carbons contained much more amounts of Ca, S, P and Mg; however, the bituminous carbons possessed higher contents of Si, Al and Fe. In addition, the content ratios of Al to Si exhibited the Al enrichment phenomenon occurred after the heat treatment. A nonlinear correlation between the pH value and the difference in the amounts of basic and acidic groups was developed. Unfortunately, there were no specific mass ratios found among the acidic functional groups. The results of correspondence analysis (CA) gave a promising confirmation about the EDXRF analysis; moreover, the results of factor analysis (FA) fairly agreed with the findings suggested by CA. Both could explain the specific chemical features of activated carbons made from different materials, especially the CA could differentiate each other in detail.     

铁钙复合絮凝剂HC211用于钻井废水处理性能研究

探讨了在不同PH值、温度、剂量及酸化预处理条件下，铁钙复合絮凝剂HC211絮凝特性和絮凝效果的好坏。研究表明铁钙复合絮凝剂HC211在PH值为8－10，温度为15℃，剂量在4‰左右有好的絮凝效果。尤其在酸化预处理后，铁钙复合絮凝剂HC211絮凝效果更佳。     

NOM characteristics and treatabilities of ozonation processes

The objectives of this study were intended to evaluate the effects of the characteristics of natural organic matter on the treatabilities of ozonation, coagulation, filtration, and granular activated carbon processes. The ultra-violet absorbance (UV254) was used as a surrogate parameter to assess each process in reducing the disinfection by-product formation potential (DBPFP). The results indicate that the DBPFP varies with the sources of water samples and treatment processes, but is closely related to the measurement of UV254/DOC. Coagulation/sedimentation can eliminate large molecular weight organic fractions. Both pre- and post-ozonation processes can reduce some of DBP precursors than the conventional treatment process, and are more reliable for reducing the overall DBPFP.     

Comparisons of metal leachability for various wastes by extraction and leaching methods

The objective of this research was to evaluate three extraction tests, i.e., toxicity characteristic leaching procedures (TCLP), extraction procedure (EP), and American Society for Testing and Materials (ASTM) methods, for their ability to extract metals in chemical sludge and incineration bottom ash, in terms of the precision of analytical results. Typical chemical sludges, including the electroplating and dye-stuff sludges, the municipal solid waste incineration bottom ash, the leather debris, and the steel-mill bottom residue containing Cd, Cr, Cu, Pb, and Zn were prepared for the lysimetry test (dynamic testing) to compare with the extraction results. Results show that for bottom residue and dye-stuff sludge, the concentration of metal leached was almost the same between the lysimetry leaching and the TCLP tests. The metal concentration followed the order: TCLP approximately = EP > ASTM. TCLP and EP exhibited almost the same relative standard deviation (RSD) value. Therefore, the results of the TCLP tests for bottom residue and dye-stuff sludge, which have a low metal content and alkalinity, can be used to estimate the metal concentration leached by typical acid rain in Taiwan; whereas the ASTM extraction test may be a better indicator of the lysimetry test.     

Analyzing the uncorrected error of dilution water demand for the dilution biochemical oxygen demand method.

Dilution water demand (DWD) can cause a positive error when the dilution biochemical oxygen demand (BOD) method is used. Dilution water demand may be attributed to oxidation of organic impurities in the dilution water and nitrification of ammonia added as a nutrient. To minimize the error associated with these sources, the standard BOD method requires that DWD be less than 0.2 mg/L in 5 days and does not allow correction for DWD when calculating test results. This study derives a set of theoretical equations to analyze the uncorrected errors with and without seeding. The authors concluded that DWD can be completely corrected if seeded dilution water is used for the sample dilution. When seeding individual bottles, the uncorrected error approaches 8.3 to approximately 8.8% at a 5-day depletion of 2 mg/L for a typical secondary effluent. Tests without seeding show an almost 1% higher uncorrected error than seeded tests. The analysis also suggests that these errors can be effectively reduced to less than 3% when the 5-day depletion approaches 6 mg/L. even for 5-day biochemical oxygen demand concentrations exceeding I x 10(4) mg/L. Further analysis indicates that, if not inhibited, the ammonium added to dilution water as a nutrient may contribute additional error due to nitrification.     

Modeling VOCs adsorption onto activated carbon

The activated carbon adsorption process is affected by the characteristics of adsorbent, adsorbate and environmental conditions. In this study, both adsorption and desorption processes are assumed to occur simultaneously and a numerical model was developed with a non-linear driving force in conjunction with the Langmuir model for predicting the overall adsorption process. The numerical model provides both adsorption and desorption rate constants and activation energies. The resultant equilibrium constants are of the same order of magnitude as reported by other studies. Results show that the model could well predict the adsorption isotherms and breakthrough curves under various conditions.     

Diffusion of hydrogen sulfide and methyl mercaptan onto microporous alkaline activated carbon

Activated carbon kinetic studies show that both H2S and CH3SH yielded pore diffusion coefficients from 10(-6) to 10(-8) cm2/s. Results indicated that pore structures could influence effective diffusivity. Under the same adsorbate concentration, CH3SH exhibited a greater effective pore diffusion coefficient than H2S. This may be attributed to the fact that CH3SH has both polar (-SH) and non-polar (-CH3) functional groups and dissolves into water easier, thus providing more attraction for the activated carbon surface. In addition, the saturation vapor pressure of CH3SH is lower than that of H2S. Therefore, CH3SH is easier to adsorb onto activated carbon than H2S.     

Effects of bromide on the formation of THMs and HAAs

The role of bromide in the formation and speciation of disinfection by-products (DBPs) during chlorination was investigated. The molar ratio of applied chlorine to bromide is an important factor in the formation and speciation of trihalomethanes (THMs) and halogenacetic acids (HAAs). A good relationship exists between the molar fractions of THMs and the bromide incorporation factor. The halogen substitution ability of HOBr and HOCl during the formation of THMs and HAAs can be determined based on probability theory. The formation of HAAs, and their respective concentrations, can also be estimated through use of the developed model.     

Adsorption/desorption properties of copper ions on the surface of iron-coated sand using BET and EDAX analyses

This study was conducted to develop a heating process for coating hydrated iron oxide on the sand surface to utilise the adsorbent properties of the coating and the filtration properties of the sand. BET and scanning electron microscope (SEM) analyses were used to investigate the surface properties of the coated layer. An energy dispersive X-ray (EDAX) technique of analysis was used for characterising metal adsorption sites on the iron-coated sand surface. The results indicated that the iron-coated sand had more micropores and higher specific surface area because of the attachment of iron oxide. Copper ions could penetrate into the micropores and mesopores of iron oxide on sand surface, and the regeneration of the iron-coated sand could be achieved by soaking with pH = 3.0 acid solution. Besides, the results of EDAX analysis showed that copper ions were chemisorbed on the surface of iron-coated sand. Results of the study developed an innovative technology for coating iron oxide on sand surface for the treatment of heavy metal in water.