Solid phase extraction of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) ions with 1-(2-thiazolylazo)-2-naphthol loaded Amberlite XAD-1180

A new method for separation and preconcentration of trace amounts of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) ions in various matrices was proposed. The method is based on the adsorption and chelation of the metal ions on a column containing Amberlite XAD-1180 resin impregnated with 1-(2-thiazolylazo)-2-naphthol (TAN) reagent prior to their determination by flame atomic absorption spectrometry (FAAS). The effect of pH, type, concentration and volume of eluent, sample volume, flow rates of sample and elution solutions, and interfering ions have been investigated. The optimum pH for simultaneous retention of all the metal ions was 9. Eluent for quantitative elution was 20 ml of 2 mol l(-1) HNO(3). The optimum sample and eluent flow rates were found as 4 ml min(-1), and also sample volume was 500 ml, except for Mn (87% recovery). The sorption capacity of the resin was found to be 0.77, 0.41, 0.57, and 0.30 mg g(-1) for Cu(II), Ni(II), Cd(II), and Mn(II), respectively. The preconcentration factor of the method was 200 for Cu(II), 150 for Pb(II), 100 for Cd(II) and Ni(II), and 50 for Mn(II). The recovery values for all of the metal ions were > or = 95% and relative standard deviations (RSDs) were < or = 5.1%. The detection limit values were in the range of 0.03 and 1.19 microg l(-1). The accuracy of the method was confirmed by analysing the certified reference materials (TMDA 54.4 fortified lake water and GBW 07605 tea samples) and the recovery studies. This procedure was applied to the determination of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) in waste water and lake water samples.     

Assessment of the clear-sky bias issue using continuous PM10 data from two AERONET sites in Korea

A bias in clear-sky conditions that will be involved in estimating particulate matter(PM)concentration from aerosol optical depth(AOD) was examined using PM_(10) from two Aerosol Robotic Network sites in Korea. The study periods were between 2004 and 2007 at Anmyon and between 2003 and 2011 at Gosan, when both PM_(10) and AOD were available. Mean PM_(10) when AOD was available(PM AOD) was higher than that from all PM_(10)data(PM all) by 5.1 and9.9 μg/m~3 at Anmyon and Gosan, which accounted for 11% and 26% of PM all, respectively.Because of a difference between mean PM_(10) under daytime clear-sky conditions(PM clear)and PM AOD, the variations in ΔPM_(10), the difference of PM all from PM clear rather than from PM AOD, were investigated. Although monthly variations in ΔPM_(10)at the two sites were different, they were positively correlated to those in ΔT, similarly defined as ΔPM_(10)except for temperature, at both sites. ΔPM_(10)at Anmyon decreased to a negative value in January due to an influence of the Siberian continental high-pressure system while ΔPM_(10)at Gosan was high in winter due to an effect of photochemical production at higher temperatures than at Anmyon.     

Dietary exposure to di-isobutyl phthalate increases urinary 5-methyl-2′-deoxycytidine level and affects reproductive function in adult male mice

Phthalates are a large family of ubiquitous environmental pollutants suspected of being endocrine disruptors. Epidemiological studies have associated phthalate metabolites with decreased reproductive parameters and linked phthalate exposure with the level of urinary 5-methyl-2′-deoxycytidine(5mdC, a product of methylated DNA). In this study, adult male mice were exposed to 450 mg di-isobutyl phthalate(DiBP)/(kg·day) via dietary exposure for 28 days. Mono-isobutyl phthalate(Mi BP, the urinary metabolite) and reproductive function parameters were determined. The levels of 5mdC and 5-hydroxymethyl-2′-deoxycytidine(5hmdC) were measured in urine to evaluate if their contents were also altered by DiBP exposure in this animal model. Results showed that DiBP exposure led to a significant increase in the urinary 5mdC level and significant decreases in sperm concentration and motility in the epididymis, accompanied with reduced testosterone levels and downregulation of the P450 cholesterol side-chain cleavage enzyme(P450scc) gene in the mice testes. Our findings indicated that exposure to DiBP increased the urinary 5mdC levels,which supported our recent epidemiological study about the associations of urinary 5mdC with phthalate exposure in the male human population. In addition, DiBP exposure impaired male reproductive function, possibly by disturbing testosterone levels; P450scc might be a major steroidogenic enzyme targeted by DiBP or other phthalates.     

Mesoporous carbon nanomaterials induced pulmonary surfactant inhibition, cytotoxicity, inflammation and lung fibrosis

Environmental exposure and health risk upon engineered nanomaterials are increasingly concerned. The family of mesoporous carbon nanomaterials(MCNs) is a rising star in nanotechnology for multidisciplinary research with versatile applications in electronics,energy and gas storage, and biomedicine. Meanwhile, there is mounting concern on their environmental health risks due to the growing production and usage of MCNs. The lung is the primary site for particle invasion under environmental exposure to nanomaterials. Here, we studied the comprehensive toxicological profile of MCNs in the lung under the scenario of moderate environmental exposure. It was found that at a low concentration of 10 μg/mL MCNs induced biophysical inhibition of natural pulmonary surfactant. Moreover, MCNs at similar concentrations reduced viability of J774 A.1 macrophages and lung epithelial A549 cells.Incubating with nature pulmonary surfactant effectively reduced the cytotoxicity of MCNs.Regarding the pro-inflammatory responses, MCNs activated macrophages in vitro, and stimulated lung inflammation in mice after inhalation exposure, associated with lung fibrosis.Moreover, we found that the size of MCNs played a significant role in regulating cytotoxicity and pro-inflammatory potential of this nanomaterial. In general, larger MCNs induced more pronounced cytotoxic and pro-inflammatory effects than their smaller counterparts. Our results provided valuable information on the toxicological profile and environmental health risks of MCNs, and suggested that fine-tuning the size of MCNs could be a practical precautionary design strategy to increase safety and biocompatibility of this nanomaterial.     

Use of ATP Readings to Predict a Successful Hygiene Intervention in the Workplace to Reduce the Spread of Viruses on Fomites

The purpose of this study was to validate the use of adenosine triphosphate (ATP) for evaluating hygiene intervention effectiveness in reducing viral dissemination in an office environment. The bacterial virus MS-2 was used to evaluate two scenarios, one where the hand of an individual was contaminated and another where a fomite was contaminated. MS-2 was selected as a model because its shape and size are similar to many human pathogenic viruses. Two separate experiments were conducted, one in which the entrance door push plate was inoculated and the other in which the hand of one selected employee was inoculated. In both scenarios, 54 selected surfaces in the office were tested to assess the dissemination of the virus within the office. Associated surface contamination was also measured employing an ATP meter. More than half of the tested hands and surfaces in the office were contaminated with MS-2 within 4 h. Next, an intervention was conducted, and each scenario was repeated. Half of the participating employees were provided hand sanitizer, facial tissues, and disinfecting wipes, and were instructed in their use. A significant (p < 0.05) reduction was observed in the number of surfaces contaminated with virus. This reduction in viral spread was evident from the results of both viral culture and the surface ATP measurements, although there was no direct correlation between ATP measurements with respect to viral concentration. Although ATP does not measure viruses, these results demonstrate that ATP measurements could be useful for evaluating the effectiveness of hygiene interventions aimed at preventing viral spread in the workplace.     

Formic acid as an alternative reducing agent for the catalytic nitrate reduction in aqueous media

Formic acid was used for the nitrate reduction as a reductant in the presence of Pd:Cu/γ-alumina catalysts. The surface characteristics of the bimetallic catalyst synthesized by wet impregnation were investigated by SEM, TEM-EDS. The metals were not distributed homogeneously on the surface of catalyst, although the total contents of both metals in particles agreed well with the theoretical values. Formic acid decomposition on the catalyst surface, its influence on solution pH and nitrate removal efficacy was investigated. The best removal of nitrate (50 ppm) was obtained under the condition of 0.75 g/L catalyst with Pd:Cu ratio (4:1) and two fold excess of formic acid. Formic acid decay patterns resembled those of nitrate removal, showing a linear relationship between kf (formic acid decay) and k (nitrate removal). Negligible amount of ammonia was detected, and no nitrite was detected, possibly due to buffering effect of bicarbonate that is in situ produced by the decomposition of formic acid, and due to the sustained release of H2 gas.     

Tool wear of coated drills in drilling CFRP

This study aimed to investigate the wear of certain coated drills when drilling carbon fiber reinforced composites (CFRP). Three different drills were used in the drilling experiments: uncoated, diamond coated and AlTiN coated carbide (WC–Co) drills. The tool wear in CFRP machining was quite different from that in conventional metal machining. The primary wear type was a dulling or blunting of the cutting edge, which has been referred to as edge rounding wear or edge recession. In this paper, a hypothesis has been developed to explain the edge rounding wear in CFRP machining. Due to the fracture-based chip formation of CFRP, there is lack of the work material stagnation zone in front of the cutting edge, which normally prevents the edge wear in metal machining. Series of wear lead to rapid dulling of the cutting edge. The resistance to edge rounding wear on the coated as well as uncoated drills has been investigated. The diamond coating significantly reduces the edge rounding wear. However, AlTiN coated drills showed no visible improvement over the uncoated carbide drill, despite of their high hardness, thus not protecting the drill. The wear mechanisms of the uncoated carbide drill and coatings are discussed. It is believed that the 2-body and 3-body abrasive wear fail to explain the observed tool wear in CFRP drilling. However, the wear of the coatings and uncoated carbide substrate from tribo-meter tests correlated well with the tool wear in the CFRP drilling. Therefore, the tribo-meter test can be used to screen the prospective tool materials before carrying drilling experiment.     

Insertable thin film thermocouples for in situ transient temperature monitoring in ultrasonic metal welding of battery tabs

Real-time monitoring and control of temperature in ultrasonic joining of battery tabs and coupons are important for the quality improvement and cost reduction of battery assembly. However, there have always been difficulties in accurate and real-time measurement of temperature by conventional sensors for practical implementation. In this study, an innovative method is developed to provide an enabling technology for the in situ transient temperature monitoring, which could provide reliable feedback signals for potential control of ultrasonic joining processes. Micro thin film thermocouples (TFTCs) were fabricated on thin silicon substrates, which were then inserted in the welding anvil as a permanent feature so that the sensors were always located about 100 μm directly under the welding spot during joining of multilayer Ni-coated Cu thin sheets for battery assembly. Good repeatability was demonstrated while a temperature rise of up to 650 °C was obtained due to the closeness of the sensors to the welding spot. The inserts with thin film sensors remained functional after welding experiments. This method has a great potential for in situ transient temperature monitoring, and thus the control of ultrasonic joining processes to realize a practical smart joining system.     

Building regional priorities in forests for development and adaptation to climate change in the Congo Basin

Indentifying common priorities in shared natural resource systems constitutes an important platform for implementing adaptation and a major step in sharing a common responsibility in addressing climate change. Predominated by discourses on REDD + (Reduced Emissions from Deforestation and Forest Degradation and conservation, sustainable management of forests and enhancement of forest carbon stocks in developing countries) with little emphasis on adaptation there is a risk of lack of policy measures in addressing climate change in the Congo Basin. Forest products and ecosystem services provide security portfolios for the predominantly rural communities, and play major roles in national development programmes in both revenue and employment opportunities. Thus, raising the profile of forests in the policy arena especially in the twin roles of addressing climate change in mitigation and adaptation and achieving resilient development is crucial. Within the framework of the Congo Basin Forests and Climate Change Adaptation project (COFCCA) project, science policy dialogue was conducted to identify and prioritize forest based sectors vulnerable to climate change but important to household livelihoods and national development. The goal of the prioritization process was for the development of intervention in forest as measures for climate change adaptation in Central Africa. Participants constituted a wide range of stakeholders (government, Non Governmental Organizations, research institutions, universities, community leaders, private sectors etc.) as representatives from three countries directly involved in the project: Cameroon, Central African Republic and Democratic Republic of Congo. Building on national priorities, four forest related sectors were identified as common priorities at the regional level for focus on climate change adaptation. These sectors included: (1) energy with emphasis on fuel wood and Charcoal; (2) Water principally quality, quantity, accessibility, etc.; (3) Food with emphasis on Non Timber Forest Products, and (4) Health linked to healthcare products (medicinal plants). Using these prioritized sectors, the project focused on addressing the impacts of climate change on local communities and the development of adaptation strategies in the three pilot countries of the Congo Basin region. The four sectors constitute the key for development in the region and equally considered as priority sectors in the poverty reduction papers. Focused research on these sectors can help to inject the role of forests in national and local development and their potentials contributions to climate change adaptation in national and public discourses. Mainstreaming forest for climate change adaptation into national development planning is the key to improve policy coherence and effectiveness in forest management in the region.     

水溶性有机物电子转移能力与荧光峰强度的关系研究

以不同来源的水溶性有机物（DOM）为供试材料,采用电化学方法和荧光光谱法研究了DOM电子转移能力及其与荧光峰强度的关系.采用库仑安培法测定DOM电子转移能力,其中测得的电子接受能力为635.6～1 049.3μmol.（g.C）-1,电子供给能力为27.3～42.3μmol.（g.C）-1.利用循环伏安法研究DOM电化学活性,发现其氧化还原电位在-731～-996 mV（vs.Ag/AgCl）之间.经过电位跃阶法三次氧化还原循环后电子转移能力仍可维持在232.1～897.2μmol.（g.C）-1之间,电子循环率为36.7%～78.2%,说明DOM具有重复利用、反复转移电子的特性.采用荧光激发发射光谱法（EEMS）测定DOM的类富里酸荧光峰强度并比较其与DOM电子转移能力的关系,发现DOM的类富里酸荧光峰强度与DOM的电子循环率具有显著相关（r2=0.92）.实验结果为理解DOM在元素循环、污染物降解以及生物地球化学循环中的作用提供科学依据.