不同运行模式对同步脱氮除磷CAST工艺快速启动及其稳定维持的影响

以实际生活污水为处理对象,考察了传统进水/曝气和改良型分段进水的交替缺氧-好氧(A/O)2种运行模式对CAST工艺的快速启动及脱氮除磷性能稳定维持的影响。结果表明,传统进水/曝气运行模式下,系统达到最佳营养物去除性能所需启动时间30 d,稳定运行阶段TN平均去除80.66%,磷的去除率维持在66.30%左右;采用改良型交替运行模式,反应器达到稳定运行状态仅需18 d,系统稳定运行时TN平均去除81.36%,磷去除率稳定维持在90%以上,出水磷浓度在0.3 mg/L以下,出水水质达到国家污水综合排放标准一级A(GB8978-2002)。研究还发现,传统运行模式下,由低温引起的污泥沉降性能变差导致系统污泥严重流失,反应器几乎丧失污染物去除性能;而低温对交替运行模式下的反应器除磷性能几乎没有影响,总氮去除则因氨氮不完全硝化而大大降低。     

长三角地区城市居民出行交通碳排放特征与影响机理

随着能源问题及全球变化关注,城市居民出行交通碳排放研究已成为多学科关注焦点。选择南京、宁波和常州作为长三角典型城市,基于典型居住小区问卷调查获取第一手的城市居民出行基础数据,估算与分析城市居民出行碳排放特征及影响机理。结果表明：长三角2010年城市居民人均出行交通碳排放约1 1219 kg CO2/人,日常通勤和远距离出行碳排放量之比为75[DK]∶25;城市居民日常通勤交通碳排放的主要影响因子为交通方式、出行距离、家庭年收入、年龄和性别;远距离出行交通碳排放的主要影响因子为出行距离、交通方式和家庭年收入。建议采用差别化的行政干预和经济杠杆有效调控家庭小汽车保有量增长速度,鼓励小排量汽车和清洁能源汽车消费,兼顾汽车产业发展、家庭小汽车刚性需求与节能减排需求之间的博弈平衡;优化城市功能格局,大力发展公共交通网络;加强节能减排与低碳意识宣传,鼓励与引导公共交通出行     

面源磷负荷改进输出系数模型及其应用

传统的输出系数模型是模拟较大流域面源污染的有效手段,但它假设同一土地利用类型的输出系数相同,忽视了营养物径流和截留过程中其他流域特征对输出系数空间分布的影响,难以为流域分区管理提供依据。在传统输出系数模型基础上,引入产污因子（CI）和截留因子（RI）,校正地形、降雨、植被缓冲带对面源磷流失空间格局的影响。用改进输出系数模型模拟滇池流域面源磷负荷并将模拟结果应用于流域管理。结果表明,改进的输出系数模型能更好地模拟面源磷污染的空间格局,识别出面源总磷的关键风险区--湖滨平原地带以及与入滇河流邻近的山谷、台地。以2008年滇池流域面源总磷的模拟结果（3525 t）为基准,若单位面积磷肥施用量减少20%,面源总磷负荷将减少86%;若环湖公路内侧全部实现退耕还林或还草,面源总磷负荷将减少60%;若同时实施减少磷肥施用量和环湖公路内退耕两项措施,面源总磷负荷将减少130%     

响应面分析法优化稀土废水MAP沉淀法脱氮

经过预处理后的稀土生产废水,其氨氮浓度大幅降低,但并未达到中华人民共和国《稀土工业污染物排放标准》（GB26451-2011）中氨氮浓度限值。实验通过响应面分析法中的Box-Behnken实验设计（BBD）,取pH、n（Mg）：n（N）、n（P）：n（N）3因素,采用Design-Expert 8.0.6,建立合适的剩余氨氮浓度及剩余总磷浓度模型,得到回归方程,并分析模型各项指标,各因素及其相互作用对剩余氨氮浓度及剩余总磷浓度的影响。利用预测模型预测最佳实验条件,在最佳实验条件下验证预测结果,并对沉淀物进行X射线衍射（XRD）分析。结果显示,二次响应模型适用于剩余氨氮浓度及剩余总磷浓度,2个模型均拥有较好的拟合程度、可信度及精密度,最优反应条件为：pH=9.88、n（Mg）：n（N）=1.50：1、n（P）：n（N）=1.38：1时,剩余氨氮浓度为46.58 mg/L,剩余总磷浓度为7.85 mg/L。在最优条件下所得到的沉淀物并非纯净的MgNH₄PO₄·6H₂O,还有Mg₃（PO₄）₂·22H₂O生成。     

螯合树脂去除丙烯酸丁酯废水中的二价阳离子

采用氨基膦酸螯合树脂C-900去除丙烯酸丁酯废水中的二价阳离子,考察了吸附温度和废水流量对树脂动态吸附性能的影响,并用Thomas模型进行动态吸附数据的拟合分析。实验结果表明,在吸附温度为35℃、废水流量为15SV的条件下,处理后出水中3种二价阳离子总质量浓度为1.0mg/L时的穿透体积为240BV,达到穿透体积时树脂对Ca²⁺,Mg²⁺,Cu²⁺的去除率分别为100%,99.2%,99.8%。     

The life cycle assessment of an e-waste treatment enterprise in China

Electrical and electronic waste (e-waste) has become one of the fastest growing waste streams in the world, and many countries have established e-waste treatment enterprises to solve their e-waste problems. In this study, a life cycle assessment (LCA) was undertaken to quantitatively investigate the environmental impacts of an e-waste treatment enterprise in China. The LCA is constructed by SimaPro software version 7.2 and expressed with the Eco-indicator 99 life cycle impact assessment method. For a sensitivity analysis of the overall LCA results, the so-called CML method is used in order to estimate the influence of the choice of the assessment method on the result. According to the survey data, discarded TV sets accounted for the highest proportion of e-waste treated in the enterprise in 2010. The e-waste treatment had little environmental impact, and at the same time large environmental benefits can be achieved mainly due to the recycled resources and reuse of some components. Based on the research results, it can be seen that recycled metal, especially copper, would be of more importance for environmental benefits. Relevant results and data from this study could provide decision support to enterprise managers and government sectors.     

Functional groups of marine ciliated protozoa and their relationships to water quality

Ciliated protozoa (ciliates) play important ecological roles in coastal waters, especially regarding their interaction with environmental parameters. In order to increase our knowledge and understanding on the functional structure of ciliate communities and their relationships to environmental conditions in marine ecosystems, a 12-month study was carried out in a semi-enclosed bay in northern China. Samples were collected biweekly at five sampling stations with differing levels of pollution/eutrophication, giving a total of 120 samples. Thirteen functional groups of ciliates (A–M) were defined based on their specific spatio-temporal distribution and relationships to physico-chemical parameters. Six of these groups (H–M) were the primary contributors to the ciliate communities in the polluted/eutrophic areas, whereas the other seven groups (A–G) dominated the communities in less polluted areas. Six groups (A, D, G, H, I and K) dominated during the warm seasons (summer and autumn), with the other seven (B, C, E, F, J, L and M) dominating in the cold seasons (spring and winter). Of these, groups B (mainly aloricate ciliates), I (aloricate ciliates) and L (mainly loricate tintinnids) were the primary contributors to the communities. It was also shown that aloricate ciliates and tintinnids represented different roles in structuring and functioning of the communities. The results suggest that the ciliate communities may be constructed by several functional groups in response to the environmental conditions. Thus, we conclude that these functional groups might be potentially useful bioindicators for bioassessment and conservation in marine habitats.     

Phosphine in paddy fields and the effects of environmental factors

Ambient levels of phosphine (PH₃) in the air, phosphine emission fluxes from paddy fields and rice plants, and the distribution of matrix-bound phosphine (MBP) in paddy soils were investigated throughout the growing stages of rice. The relationships between MBP and environmental factors were analyzed to identify the principal factors determining the distribution of MBP. The phosphine ambient levels ranged from 2.368 ± 0.6060 ng m⁻³ to 24.83 ± 6.529 ng m⁻³ and averaged 14.25 ± 4.547 ng m⁻³. The highest phosphine emission flux was 22.54 ± 3.897 ng (m² h)⁻¹, the lowest flux was 7.64 ± 4.83 ng (m² h)⁻¹, and the average flux was 14.17 ± 4.977 ng (m² h)⁻¹. Rice plants transport a significant portion of the phosphine emitted from the paddy fields. The highest contribution rate of rice plants to the phosphine emission fluxes reached 73.73% and the average contribution was 43.00%. The average MBP content of 111.6 ng kg⁻¹fluctuated significantly in different stages of rice growth and initially increased then decreased with increasing depth. The peak MBP content in each growth stage occurred approximately 10 cm under the surface of paddy soils. Pearson correlation analyses and stepwise multiple regression analysis showed that soil temperature (Ts), acid phosphatase (ACP) and total phosphorus (TP) were the principal environmental factors, with correlative rankings of Ts > ACP > TP.     

金属负载型催化剂对烟气脱硫性能的影响

介绍了国内外烟气脱硫催化剂的研究现状,研究了金属氧化物负载型催化剂对烟气脱硫性能的影响。以活性炭(AC)为载体,选用8种不同的金属硝酸盐作为浸渍液,采用等体积浸渍法制备金属氧化物负载型催化剂。以脱硫效果较好的Fe2O3/AC为例,研究了不同焙烧温度、金属负载量以及焙烧时间对催化剂脱硫性能的影响。实验结果表明,Fe2O3/AC催化剂脱硫率随着金属负载量的增加呈递增趋势,最优金属负载量为10.0%(质量分数);脱硫率随着焙烧温度的增加显著提高,最优焙烧温度为350℃;脱硫率随着焙烧时间的增加而提高,最优焙烧时间为3.0h。     

添加剂对炭黑颗粒润湿和沉降性能的影响

为提高湿式除尘装置对炭黑颗粒物的去除效率,通过向吸收液中添加复配表面活性剂以提高吸收液对炭黑的润湿性,投加絮凝剂使进入吸收液的炭黑颗粒发生凝聚和沉降,从而使吸收液得以循环利用。其中表面活性剂的复配以非离子表面活性剂月桂醇聚氧乙烯（9）醚（AEO-9）为主,与十二烷基苯磺酸钠（SDBS）、十六烷基三甲基溴化胺（CTAB）和壬酚基聚氧乙烯醚（TX-10）分别复配,筛选出复配效果最好的一组复配液;然后投加絮凝剂,探讨絮凝剂的加入对吸收液中炭黑颗粒物絮凝沉降的影响。结果表明,在AEO-9浓度为0．05mmol／L,TX-10浓度为0．09mmol／L时,吸收液的表面张力最小,为36．75mN／m;投加无机絮凝剂聚合氯化铝（PAC）浓度为100mg／L时,经15min沉降,炭黑的沉降率可达88．1％,上清液中悬浮颗粒的平均粒径为6．36μm。