Seasonal variation and size distribution of biogenic secondary organic aerosols at urban and continental background sites of China

Size-resolved biogenic secondary organic aerosols(BSOA) derived from isoprene and monoterpene photooxidation in Qinghai Lake, Tibetan Plateau(a continental background site) and five cities of China were measured using gas chromatography/mass spectrometry(GC/MS). Concentrations of the determined BSOA are higher in the cities than in the background and are also higher in summer than in winter. Moreover, strong positive correlations(R2= 0.44–0.90) between BSOA and sulfate were found at the six sites,suggesting that anthropogenic pollution(i.e., sulfate) could enhance SOA formation,because sulfate provides a surface favorable for acid-catalyzed formation of BSOA. Size distribution measurements showed that most of the determined SOA tracers are enriched in the fine mode( 3.3 μm) except for cis-pinic and cis-pinonic acids, both presented a comparable mass in the fine and coarse( 3.3 μm) modes, respectively. Mass ratio of oxidation products derived from isoprene to those from monoterpene in the five urban regions during summer are much less than those in Qinghai Lake region. In addition, in the five urban regions relative abundances of monoterpene oxidation products to SOA are much higher than those of isoprene. Such phenomena suggest that BSOA derived from monoterpenes are more abundant than those from isoprene in Chinese urban areas.     

芦苇植株对湿地温室气体排放的影响及其日变化特征

利用静态箱-气相色谱法对夏季(7月、8月和9月)长江河口湿地芦苇植被CO_2、CH_4和N_2O的叶面通量、茎秆扩散速率以及沉积物通量的日变化进行研究。结果显示,通过芦苇叶片排放的N_2O与CH_4的量分别为2.99μg/(m~2·h)和15.36μg/(m~2·h),CO_2则呈现白天吸收(-120.86 mg/(m~2·h))、夜间排放(69.39 mg/(m~2·h))的特点。芦苇茎秆N_2O、CH_4和CO_2平均扩散速率分别为1.96μg/h、142.45μg/h和10.69 mg/h,沉积物平均排放通量为N_2O 8.18μg/(m~2·h)、CH_41.58 mg/(m~2·h)、CO_2169.66 mg/(m~2·h)。芦苇茎秆和沉积物界面CH_4和CO_2的排放均呈现出明显的"单峰型"昼夜变化规律,其排放峰值集中在日照及温度最高的9:00至15:00。芦苇植株是影响温室气体排放变化的因素之一。芦苇植株在光合作用下吸收CO_2并促进CH_4的排放,而芦苇发达的根系及茎秆是温室气体排放的主要途径。同时,Pearson相关性分析表明温度对芦苇群落CH_4和NO2的排放影响显著,但与CO_2通量的相关性不明显。土壤氧化还原电位对3种气体的排放均有显著影响。     

In vitro studies of the submerged angiospermRuppia maritima: Auxin and cytokinin effects on plant growth and development

Axenic tissue cultures ofRuppia maritima L. were established and propagated clonally in vitro from terminal rhizome segments collected from Tampa Bay, Florida, USA. Cultures were maintained in a base medium consisting of synthetic seawater supplemented with half-strength Murashige and Skoog salts and 1% sucrose at pH 5.6. The effects of five cytokins [6-furfurylaminopurine (kinetin), 6-benzylaminopurine (BAP), 2-isopentyladenine (2iP), 6-(4-hydroxy-3-methyl-but-2-enylamino) purine (zeatin), andn-phenyl-n-1,2,3-thidiazol-5yl urea (thidiazuron)] and one auxin [napthalene acetic acid (NAA)] on explant growth and development were investigated. Cytokinin additions resulted in a 3- to 4-fold increase in nodal production, branching, and biomass ofR. maritima after 12 wk in culture. Cultures responded in a dose-dependent manner to 2iP but exhibited broad dose-response curves to kinetin, BAP, zeatin, and thidiazuron. NAA addition resulted in increased leaf and internodal lengths, but reduced the number of leaves per node and the rhizome biomass. The addition of NAA almost completely suppressed root growth in media without cytokinins and had an antagonistic effect on nodal production and branching in cytokinin-supplemented media.     

A comparison of (Pb, Cd and Zn) accumulation in terrestrial slugs maintained in microcosms: evidence for metal tolerance

The relative tissue accumulation of Pb, Cd and Zn were compared in two populations each of two species of slugs (Arion subfuscus and Deroceras reticulatum). One population was resident at a contaminated Pb/Zn mine site, and the other population was from an uncontaminated site and was transferred for 20 days to microcosms established at the mine site. It was found that when the experiment was conducted during late spring (May), but not in late winter (February), that the Pb and Zn concentrations in the tissues of the 'transplants', were significantly higher than in the tissues of 'residents'; the Cd concentrations in the transplants, although significantly higher in the May sample than in February, did not exceed those of their 'resident' counterparts. It was postulated that: (a) Pb and Zn tolerance in slugs is phenotypically expressed by a reduction in metal accumulation; (b) Cd tolerance, if present, may be characterized by enhanced storage capacity; and (c) the presence of local metal-tolerant ecotypes is a biotic variable that may confound the relationship between dry tissue and environmental metal concentrations that forms a basis of pollution biomonitoring.     

Impact of sulphur dioxide exposure on conidial germination of powdery mildew fungi

The impact of sulphur dioxide, in two different concentrations (286 microg m(-3) and 571 microg m(-3)) for various exposure periods, on conidial germination of some powdery mildew fungi was investigated in artificial treatment conditions. SO(2) in general was inhibitory for conidial germination of all the studied powdery mildew fungi and the species did not differ much from each other in their sensitivity to SO(2). The per cent conidial germination was increasingly inhibited with an increase in the concentration of SO(2). The concentration of SO(2) and the exposure period were important determinants of the inhibitory effect.     

Development of monitoring technology for airborne particulate matter

Particulate matter suspended in the air has adverse effects onhuman health. Its level of concentration is an important parameter in evaluating the degree of hazard it poses to the atmosphere. Conventional methods used in measuring particulatematter are often filter-based, which indicates some disadvantagesbecause such a base requires labor and time. In this study, to achieve real-time measurements, a new electrical method was developed for measuring PM10 and PM2.5 concentrations. The basicprinciple is to electrically charge particles passing through thePM inlet using a corona charger and measure the currents createdby charged particles to obtain the number concentration of particulate matter. A new type inlet based on the particle cupimpactor configuration was designed and its performance was evaluated. A unipolar diffusion charger was developed and thecharger's efficiency was determined experimentally in terms ofPn, which represents the penetration through the charger,P, times the average charge number acquired by a particle,n, for different particle sizes. The correlation was constructed between the PM10 (or the PM2.5) mass concentrationsand the electrical currents due to particles, which were chargedby the diffusion charger.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.