有机氮替代比例对冬小麦/夏玉米轮作体系作物产量及N2O排放的影响

控制农业温室气体排放(如N_2O)是减缓全球气候变暖的一个重要措施.本研究通过动态监测小麦-玉米轮作体系N_2O排放通量,探究不施任何肥料(对照,CK)、单施氮磷钾化肥(NPK)、75%NPK+25%(有机氮M)(25%M)、50%NPK+50%M(50%M)、25%NPK+75%M(75%M)以及100%M,即不同有机氮替代比例对陕西关中塿土冬小麦/夏玉米轮作体系N_2O排放及作物产量的影响.结果表明,各处理N_2O排放通量在施肥、降雨或灌水后出现排放峰值.在小麦季各处理变化幅度为-1.33~144.2μg·(m~2·h)~(-1),其中NPK处理峰值最高.玉米季各处理变化幅度为88.2~1 800.1μg·(m~2·h)~(-1),50%M处理峰值最高.小麦/玉米一个轮作年不同处理N_2O排放总量为429.8~2 632.1 g·hm~(-2),且50%M25%MNPK75%M100%MCK.无论小麦、玉米还是一个轮作年总产量,施肥处理产量均显著高于对照.小麦季,施用有机肥的处理小麦产量均显著高于单施化肥处理,增幅达26.1%~50.0%.玉米季,50%M和75%M处理产量与NPK相似,而25%M和100%M处理玉米产量显著低于NPK处理.小麦/玉米轮作总产量变幅为9 166~17 496 kg·hm~(-2),其中50%M和75%M处理显著高于NPK处理,25%M和100%M处理与NPK处理无显著差异.综合考虑塿土小麦/玉米轮作体系有机氮替代化肥氮75%最好,可以保证作物产量、实现N_2O减排.     

微絮凝对腐殖酸超滤过程膜污染的减缓特性

以硫酸铝[Al_2(SO_4)_3·18H_2O]为絮凝剂,腐殖酸(humic acid,HA)和高岭土(Kaolin)水溶液为原水,研究微絮凝过程产生的不同絮体形态,对自制聚偏氟乙烯(PVDF)超滤膜过滤过程的影响.主要考察了微絮凝过程中絮体的特性(粒径大小及分布,分形维数)以及不同条件下形成的絮体形态对膜通量的影响,利用扫描电镜(SEM)和原子力显微镜(AFM)对污染膜的表面形貌进行表征,并测定了PVDF膜与有机污染物之间黏附力大小,来解析不同絮体形态对超滤膜的膜污染影响机制.结果表明,Al~(3+)以电性中和作用水解去除有机物,随着絮凝剂投加量的增加,絮体粒径不断增大,絮体的分形维数减小.膜通量衰减速率与絮体的粒径呈负相关,絮体粒径越大,膜通量衰减速率越小,超滤过程中形成的滤饼层越疏松,同时,较小分形维数的絮体引起的膜污染较轻,其膜通量恢复率也较高.PVDF-有机污染物之间的相互作用力大小与运行初期相应污染膜通量衰减速率呈正相关.当Al~(3+)投加量为5 mg·L~(-1),初始pH=7时,HA去除率为96.7%,膜通量衰减最小,通量恢复率达到88%.     

基于分区供氧与溶解氧调控的低C/N比污水短程硝化反硝化

针对城镇污水中碳源不足、C/N比低导致脱氮性能不佳的问题,建立了A2/O中试装置,通过调整系统缺氧/好氧分区比例及好氧区溶解氧水平,探究亚硝氮积累率及氮类污染物去除情况.结果表明,在DO为2. 0～2. 5 mg·L~(-1)条件下,改变缺氧/好氧分区比例对系统的影响较小,难以实现短程硝化;当控制DO为0. 5～0. 8 mg·L~(-1)、V_缺∶V_好=1∶1时为系统最优工况,此时系统好氧区末端亚硝氮积累率稳定在62%以上,出水总氮降至9. 0 mg·L~(-1),能够实现深度脱氮的目标.分析硝化菌表观活性可知,最优工况下SAOR与SNOR分别(以N/VSS计)为0. 14 g·(g·d)~(-1)和0. 04 g·(g·d)~(-1),二者差值较试验其他阶段更为明显,即NOB活性受到更高程度抑制是提高亚硝氮积累率的直接原因. Illumina MiSeq测序结果表明,该阶段NOB数量显著低于其他阶段.通过间歇OUR法分析缺氧区进出口碳源组成情况,结果表明最优工况下系统通过短程硝化节约碳源27. 3%,可生化性COD在缺氧区消耗63. 6%,远高于其他阶段,是低C/N比城市污水实现深度脱氮的碳源有力保障.     

高砷煤燃烧影响下室内外空气砷含量特征

利用空气总悬浮物采样器和安德森颗粒物分级采样器,对陕西南部燃煤型砷中毒地区的室内外空气样品进行了采集和化学分析,探讨了室内外空气ρ(总砷)与煤w(砷)的关系,以及空气ρ(总砷)在不同粒径颗粒物中的分布特征. 结果表明:室内外空气ρ(总砷)均与煤w(砷)呈显著正相关,烤火间空气ρ(总砷)与煤w(砷)的相关系数(R)为0.80(P<0.01);室外空气ρ(总砷)平均值与当地煤w(砷)平均值的相关系数(R)为0.97(P<0.01);烤火间空气ρ(总砷)高峰主要出现在向煤炉添煤3 h后的旺火期,且旺火期的室内空气ρ(总砷)与空气ρ(粉尘)呈显著正相关(R0.74,P<0.05).与土木结构相比,砖混结构房屋有助于减少燃煤释放到空气中的砷在不同房间之间的扩散;室内不同房间之间、室外不同地点之间以及室内外的空气ρ(总砷)差异主要表现在颗粒物粒径小于2.1 μm的部分;天气状况对室内空气ρ(总砷)随颗粒物粒径的分布没有明显影响.      

变截面轻型门式刚架拼接处设计方法研究

采用ANSYS有限元分析软件,对一单层单跨变截面轻型门式刚架厂房进行有限元模拟与分析.对变截面轻型门式刚架试件进行单调和循环加载,得出试件荷载-位移曲线和滞回曲线.并对变截面柱和变截面梁翼缘进行路径分析,得出柱和梁Yon Mises应力较小与较大的位置.从结构的破坏结果得出结构易破坏与较安全的部位,以供类似工程在设计时作为参考.     

Classification of contaminants and treatability evaluation of domestic wastewater

Long-term sampling and analysis were conducted in a domestic wastewater treatment plant for the investigation on the characteristics of the representative contaminants in raw sewage such as SS, COD, BOD₅, TP, and TN. All these constituents were classified into dissolved and suspended groups by using a 0.45-μm membrane filter, and the concentration of each constituent in each group was analyzed. As a result, almost 100% of the SS was found to be suspended matter, as well as about 65% of COD, 60% of BOD₅, 50% of P, and 20% of N. All these could be easily removed by sedimentation or coagulation/sedimentation. A treatability evaluation diagram was proposed for a rational selection of wastewater treatment process in accordance with raw water quality. Translated from Water & Astewater Engineering, 2004, 30(9): 38–41 [译自: 给水排水]     

Classification of contaminants and treatability evaluation of domestic wastewater

Long-term sampling and analysis were conducted in a domestic wastewater treatment plant for the investigation on the characteristics of the representative contaminants in raw sewage such as SS, COD, BOD₅, TP, and TN. All these constituents were classified into dissolved and suspended groups by using a 0.45-μm membrane filter, and the concentration of each constituent in each group was analyzed. As a result, almost 100% of the SS was found to be suspended matter, as well as about 65% of COD, 60% of BOD₅, 50% of P, and 20% of N. All these could be easily removed by sedimentation or coagulation/sedimentation. A treatability evaluation diagram was proposed for a rational selection of wastewater treatment process in accordance with raw water quality.     

An Approach to Theoretical Modeling and Simulation of Face Milling Forces

A new approach to theoretical modeling and simulation of face milling forces is presented. The present approach is based on a predictive machining theory in which machining characteristic factors in continuous cutting with a single-point cutting tool can be predicted from the workpiece material properties, tool geometry, and cutting conditions. The action of a milling cutter is considered as the simultaneous work of a number of single-point cutting tools, and the milling forces are predicted from input data of workpiece material properties, cutter parameters and tooth geometry, cutting condition, cutter and workpiece vibration structure parameters, and types of milling. A predictive force model for face milling is developed using this approach. In the model, the workpiece material properties are considered as functions of strain, strain rate, and temperature. The ratio of cutter tooth engagement over milling is taken into account for the determination of temperature in the cutting region. Cutter runout is included in the modeling for the chip load. The relative displacement between the cutter and workpiece due to the cutter and workpiece vibration is also included in the modeling to consider the effect on the undeformed chip thickness. A milling force simulation system has been developed using the model, and face milling experimental tests have been conducted to verify the simulation system. It is shown that the simulation results agree well with experimental results.     

黄土地层浅埋暗挖隧道松散围岩压力计算*

为研究黄土地层浅埋暗挖隧道松散围岩压力特征,根据既有隧道施工现场裂缝扩展情况,假定隧道开挖后的土体存在破裂区,取一半破裂区土体进行静力极限平衡分析,考虑静止土压力、侧向土压力、隧道尺寸和土层参数对半结构的影响,推导出适用于黄土地层浅埋暗挖隧道的围岩压力解析式,确定该公式下的隧道深浅埋划分界限,并结合工程实例分析隧道埋深、静止土压力系数和侧压力系数对围岩压力的影响。研究结果表明:随隧道埋深增大,围岩压力存在峰值,围岩压力曲线呈先增大后减小的趋势;围岩压力随静止土压力系数和侧压力系数的增大而减小,但静止土压力系数对围岩压力的影响较大;将新方法得到的围岩压力值分别与现场实测值和既有理论围岩压力值进行对比,计算的垂直、侧向围岩压力值均大于实测值,且新方法的计算误差相对较小。