核壳结构KNbO3@Co(OH)2的制备及其活化过一硫酸盐降解帕珠沙星的研究

制备了以KNbO₃为载体材料的Co（OH）₂复合材料并对其进行了详细的表征,分析了材料的组成成分、组成形态进而确定了其为核壳结构形貌的KNbO₃@Co（OH）₂.利用合成的样品作为催化剂活化过一硫酸盐（peroxymonosulfate,PMS）来降解帕珠沙星（pazufloxacin,PZF）,结果表明制备的催化剂对PZF的去除效率显著增加.讨论了不同初始PMS剂量对降解效率的影响,发现随着PMS增加可活化生成更多的硫酸根自由基（sulfate radicals,SO₄^·-）和羟基自由基（hydroxyl radicals,HO^·）来降解PZF,但继续增大PMS用量降解效率未见明显提升.酸性和中性pH值条件下利于反应活化PMS降解PZF,而碱性体系减缓反应,甚至强碱体系更易形成Co（OH）₂沉淀不利于反应体系中活性组分CoOH⁺的形成,大大抑制了催化性能.此外,在体系中加入淬灭剂叔丁醇（tert-Butanol,TBA）或者乙醇（ethanol,ETOH）进行自由基的淬灭实验,结果表明SO₄^·-自由基为体系降解PZF过程中主要贡献的自由基,而HO^·自由基的贡献较少.催化剂具有较好的稳定性5次循环之后仍能在10 min之内完全去除PZF.本研究提出了新的思路为制备其他载体的Co（OH）₂核壳结构提供参考依据,同时将该催化剂结合高级氧化技术应用到水体新兴有机污染物净化领域具有很好的应用前景.     

苯醌对聚合硅酸铁多相UV-Fenton体系的增效机制

通过构建苯醌增效聚合硅酸铁多相UV-Fenton体系,讨论了体系中橙Ⅱ的脱色和降解途径.在研究苯醌浓度对聚合硅酸铁铁离子的释放、Fe²⁺与Fe³⁺之间的转化、H₂O₂分解和·OH生成影响的基础上,提出了苯醌对聚合硅酸铁多相UV-Fenton体系的增效机制.结果表明,随苯醌浓度的增加,其紫外光下光解还原聚合硅酸铁并释放Fe²⁺的程度增大、H₂O₂分解速度加快、产生·OH浓度峰值增高且出现的时间提前;苯醌增效体系释放于溶液中的Fe²⁺可以通过Fenton反应转化成Fe³⁺,反应结束后聚合硅酸铁能重新吸附Fe³⁺并使其浓度降低,避免了增效体系铁离子的二次污染.本研究将为多相催化剂催化过程的调控提供新的视角,为多相光助-芬顿反应在有机废水资源化中的应用提供理论依据和技术支持.     

Fas/FasL途径在氟暴露致PC12细胞凋亡中的作用

为了探讨Fas/FasL途径在氟暴露致PC12细胞凋亡中的作用及其机制,采用含20、40、80、160mg/L NaF培养液处理PC12细胞.结果表明,所有剂量NaF处理12、24、36、48h,PC12细胞活性升高;上述不同剂量NaF处理24h后,与对照组比,PC12细胞的活性氧水平、细胞凋亡率、细胞内Fas/FasL信号转导通路Fas和FasL、Caspase8、FADD、Caspase3基因和蛋白表达水平均呈显著上升（P < 0.05）,而Bid基因和蛋白表达水平显著下降（P < 0.05）,且呈氟暴露剂量依赖性.结果提示Fas/FasL途径在氟暴露致PC12细胞凋亡中起重要作用,其中FADD可能是Fas/FasL凋亡途径中的重要靶分子.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Revealing the changes of bacterial community from water source to consumers tap: A full-scale investigation in eastern city of China

This study profiled the bacterial community variations of water from four water treatment systems, including coagulation, sedimentation, sand filtration, ozonation-biological activated carbon filtration (O₃-BAC), disinfection, and the tap water after the distribution process in eastern China. The results showed that different water treatment processes affected the bacterial community structure in different ways. The traditional treatment processes, including coagulation, sedimentation and sand filtration, reduced the total bacterial count, while they had little effect on the bacterial community structure in the treated water (before disinfection). Compared to the traditional treatment process, O₃-BAC reduced the relative abundance of Sphingomonas in the finished water. In addition, ozonation may play a role in reducing the relative abundance of Mycobacterium. NaClO and ClO₂ had different effects on the bacterial community in the finished water. The relative abundance of some bacteria (e.g. Flavobacterium, Phreatobacter and Porphyrobacter) increased in the finished water after ClO₂ disinfection. The relative abundance of Mycobacterium and Legionella, which have been widely reported as waterborne opportunistic pathogens, increased after NaClO disinfection. In addition, some microorganisms proliferated and grew in the distribution system, which could lead to turbidity increases in the tap water. Compared to those in the finished water, the relative abundance of Sphingomonas, Hyphomicrobium, Phreatobacter, Rheinheimera, Pseudomonas and Acinetobacter increased in the tap water disinfected with NaClO, while the relative abundance of Mycobacterium increased in the tap water disinfected with ClO₂. Overall, this study provided the detailed variation in the bacterial community in the drinking water system.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Preparation of solar-enhanced AlZnO@carbon nano-substrates for remediation of textile wastewaters

Photoactive aluminum doped ZnO(AlZnO) was synthesized by sol-gel method.After that,AlZnO photocatalyst was deposited on five carbon-based materials(CBMs) using ultrasonic route followed by solid-state mixing using ball mill.The CBMs used were poly aniline(PANI),carbon nitride(CN),carbon nanotubes(CNT),graphene(G),and carbon nanofibers(CNF).The crystal phases,elemental compositions,morphological,and optical properties of the AlZnO@CBMs composites were investigated.Experimental results revealed that two of AlZnO@CBMs composites exhibited superior bleaching efficiency(100% removal) and photocatalytic stability(three cycles) for 50 μmol/L Methylene Blue(MB) contaminated water after 60 min irradiation in visible light at pH 6.5,0.7% H_2O_2,and 5 g/L inorganic salts.Under optimum conditions,AlZnO@CBMs nanocomposites were employed for the treatment of mixed dyestuffs composed of MB,Methyl Orange(MO),Astrazone Blue FRR(BB 69),and Rhodamine B(RhB) dyes under dark,ultraviolet,visible,and direct sunlight.For mixed dyestuffs,the AlZnO@G achieved the highest dye sorption capacity(60.91 μmol dye stuffs/g) with kinetic rate 8.22 × 10~(-3) min~(-1) in 90 min via multi-layer physisorption(Freundlich isotherm) on graphene sheet.In additions,AlZnO@CN offered the highest photo-kinetic rate(K_(photo)) of～54.1 × 10~(-3) min~(-1)(93.8% after 60 min) under direct sunlight.Furthermore,the selective radical trapping experiment confirmed that the holes and oxidative superoxide radicals are crucial on dyes photodegradation pathway.Owing to their superior performance,AlZnO@G and AlZnO@CN nanocomposites can offer an effective in-situ solar-assisted adsorption/photocatalytic remediation of textile wastewater effluents.     

Plasmonic silver/silver oxide nanoparticles anchored bismuth vanadate as a novel visible-light ternary photocatalyst for degrading pharmaceutical micropollutants

The degradation of pharmaceutical micropollutants is an intensifying environmental problem and synthesis of efficient photocatalysts for this purpose is one of the foremost challenges worldwide. Therefore, this study was conducted to develop novel plasmonic Ag/Ag₂O/BiVO₄ nanocomposite photocatalysts by simple precipitation and thermal decomposition methods, which could exhibit higher photocatalytic activity for mineralized pharmaceutical micropollutants. Among the different treatments, the best performance was observed for the Ag/Ag₂O/BiVO₄ nanocomposites (5 wt.%; 10 min's visible light irradiation) which exhibited 6.57 times higher photodegradation rate than the pure BiVO₄. Further, the effects of different influencing factors on the photodegradation system of tetracycline hydrochloride (TC-HCl) were investigated and the feasibility for its practical application was explored through the specific light sources, water source and cycle experiments. The mechanistic study demonstrated that the photogenerated holes (h⁺), superoxide radicals (?O₂^?) and hydroxyl radicals (?OH) participated in TC-HCl removal process, which is different from the pure BiVO₄ reaction system. Hence, the present work can provide a new approach for the formation of novel plasmonic photocatalysts with high photoactivity and can act as effective practical application for environmental remediation.     

UV/H2O2 oxidation of tri(2-chloroethyl) phosphate: Intermediate products, degradation pathway and toxicity evaluation

Tri(2-chloroethyl) phosphate (TCEP) with the initial concentration of 5 mg/L was degraded by UV/H₂O₂ oxidation process. The removal rate of TCEP in the UV/H₂O₂ system was 89.1% with the production of Cl^? and PO₄^3? of 0.23 and 0.64 mg/L. The removal rate of total organic carbon of the reaction was 48.8% and the pH reached 3.3 after the reaction. The oxidative degradation process of TCEP in the UV/H₂O₂ system obeyed the first order kinetic reaction with the apparent rate constant of 0.0025 min^?1 (R²=0.9788). The intermediate products were isolated and identified by gas chromatography-mass spectrometer. The addition reaction of HO? and H₂O and the oxidation reaction with H₂O₂ were found during the degradation pathway of 5 mg/L TCEP in the UV/H₂O₂ system. For the first time, environment risk was estimated via the “ecological structure activity relationships” program and acute and chronic toxicity changes of intermediate products were pointed out. The luminescence inhibition rate of photobacterium was used to evaluate the acute toxicity of intermediate products. The results showed that the toxicity of the intermediate products increased with the increase of reaction time, which may be due to the production of chlorine compounds. Some measures should be introduced to the UV/H₂O₂ system to remove the highly toxic Cl-containing compounds, such as a nanofiltration or reverse osmosis unit.     

Will polycentric cities cause more CO2 emissions? A case study of 232 Chinese cities

From 2000 to 2010 China experienced rapid economic development and urbanization. Many cities in economically developed areas have developed from a single-center status to polycentricity. In this study, we used exploratory spatial data analysis (ESDA) to identify the population centers, which identified 232 cities in China as having urban centers. COMP was used to represent urban agglomeration, and POLYD (representing how far is the city's sub-centers to the main center), POLYC (representing the number of a city's centers), and POLYP (representing the population distributed between the main center and the sub-centers) were used to indicate urban polycentricity. Night light data were used to determine the CO₂ emissions from various cities in China. A mixed model was used to study the impact of urban aggregation and polycentric data on the CO₂ emission efficiency in 2000 and 2010. The study found that cities with higher compactness were distributed in coastal areas, and the cities with higher multicentricity were distributed in the Yangtze River Delta and Shandong Province. The more compact the city was, the less conducive it was to improving CO₂ emission efficiency. Polycentric development of the city was conducive to improving the CO₂ emission efficiency, but the number of urban centers had no significant relationship with the CO₂ emission efficiency. Our research showed that the compactness and multicentricity of the city had an impact on the CO₂ emission efficiency and provided some planning suggestions for the low carbon development of the city.