乌鲁木齐市气溶胶光学厚度时空分布特征及潜在来源分析

依据2009年1月—2019年7月MODIS/AQUA C6.1 MYD04_L2 气溶胶光学厚度（Aerosol Optical Depth, AOD）日数据,在宏观视角下对乌鲁木齐市AOD时空分布特征进行分析,利用后向轨迹模式（Hybrid Single Particle Lagrangian Integrated Trajectory,HYSPLIT）和潜在源贡献作用分析方法（Potential Source Contribution Function, PSCF）讨论气溶胶运输的季节性变化,并揭示研究不同季节对AOD影响较为明显的潜在源空间分布.结果表明：①乌鲁木齐市AOD呈显著的季节性差异,四季均值依次为：春季（0.328） > 夏季（0.310） > 秋季（0.273） > 冬季（0.137）,AOD高值区主要集中在市区.②AOD年内呈双峰分布,峰值分别对应为4月（0.402）和8月（0.346）;10 a间AOD呈弱下降趋势,其中2014年最高（0.316）,2017年最低（0.235）,AOD均值为0. 276.③春季和冬季乌鲁木齐市气团输送主要来自中亚地区,夏季和秋季则来自于天山周边地区;AOD主要潜在源区为乌鲁木齐市及其周边地区,对乌鲁木齐市空气质量具有显著影响.     

高原高寒污水处理系统的微生物群落特征

为研究高原高寒污水处理系统活性污泥的微生物群落结构及多样性,以拉萨、云南、四川的3座高原污水厂作为实验组,同时以重庆2座非高原污水厂作为对照,采用PCR-DGGE技术对比分析了高原与非高原污水厂的微生物特性.研究表明：高原污水厂样品与非高原样品在聚类中展现出了较为疏远的关系,微生物群落区别明显.受强紫外线辐照的抑制,高原高寒污水处理系统微生物多样性的平均水平显著低于非高原污水厂,较低的微生物多样性是导致高原高寒地区污染物去除效果不佳的一项重要原因.群落构成方面,共鉴定出16个优势菌属,对应Proteobacteria、Bacteroidetes、Firmicutes、Verrucomicrobia 4个门.组间差异分析结果发现,高原组中丰度显著偏高的菌属只有Prosthecobacter,该菌在污水厂内分布广泛,且能够适应高原低温的条件.对于大多数活性污泥微生物而言,高原强紫外线是不利的生存条件.因此,减少高原露天污水处理系统的紫外辐照,是提升污水处理效能的一个潜在措施.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

Treatability studies of naphthalene in soil,water and air with persulfate activated by iron(Ⅱ)

Chemical oxidation was applied to an artificially contaminated soil with naphthalene (NAP). Evaluation of NAP distribution and mass reduction in soil, water and air phases was carried out through mass balance. Evaluation of NAP distribution and mass reduction in soil, water and air phases was carried out through mass balance. The importance of the air phase analysis was emphasized by demonstrating how NAP behaves in a sealed system over a 4 hr reaction period. Design of Experiments method was applied to the following variables: sodium persulfate concentration [SP], ferrous sulfate concentration [FeSO₄], and pH. The system operated with a prefixed solid to liquid ratio of 1:2. The following conditions resulted in optimum NAP removal [SP] = 18.37 g/L, [FeSO₄] = 4.25 g/L and pH = 3.00. At the end of the 4 hr reaction, 62% of NAP was degraded. In the soil phase, the chemical oxidation reduced the NAP concentration thus achieving levels which comply with Brazilian and USA environmental legislations. Besides the NAP partitioning view, the monitoring of each phase allowed the variabilities assessment over the process, refining the knowledge of mass reduction. Based on NAP distribution in the system, this study demonstrates the importance of evaluating the presence of semi-volatile and volatile organic compounds in the air phase during remediation, so that there is greater control of the system as to the distribution and presence of the contaminant in the environment. The results highlight the importance of treating the contaminant in all its phases at the contaminated site.     

Revealing the changes of bacterial community from water source to consumers tap: A full-scale investigation in eastern city of China

This study profiled the bacterial community variations of water from four water treatment systems, including coagulation, sedimentation, sand filtration, ozonation-biological activated carbon filtration (O₃-BAC), disinfection, and the tap water after the distribution process in eastern China. The results showed that different water treatment processes affected the bacterial community structure in different ways. The traditional treatment processes, including coagulation, sedimentation and sand filtration, reduced the total bacterial count, while they had little effect on the bacterial community structure in the treated water (before disinfection). Compared to the traditional treatment process, O₃-BAC reduced the relative abundance of Sphingomonas in the finished water. In addition, ozonation may play a role in reducing the relative abundance of Mycobacterium. NaClO and ClO₂ had different effects on the bacterial community in the finished water. The relative abundance of some bacteria (e.g. Flavobacterium, Phreatobacter and Porphyrobacter) increased in the finished water after ClO₂ disinfection. The relative abundance of Mycobacterium and Legionella, which have been widely reported as waterborne opportunistic pathogens, increased after NaClO disinfection. In addition, some microorganisms proliferated and grew in the distribution system, which could lead to turbidity increases in the tap water. Compared to those in the finished water, the relative abundance of Sphingomonas, Hyphomicrobium, Phreatobacter, Rheinheimera, Pseudomonas and Acinetobacter increased in the tap water disinfected with NaClO, while the relative abundance of Mycobacterium increased in the tap water disinfected with ClO₂. Overall, this study provided the detailed variation in the bacterial community in the drinking water system.     

Preparation of solar-enhanced AlZnO@carbon nano-substrates for remediation of textile wastewaters

Photoactive aluminum doped ZnO(AlZnO) was synthesized by sol-gel method.After that,AlZnO photocatalyst was deposited on five carbon-based materials(CBMs) using ultrasonic route followed by solid-state mixing using ball mill.The CBMs used were poly aniline(PANI),carbon nitride(CN),carbon nanotubes(CNT),graphene(G),and carbon nanofibers(CNF).The crystal phases,elemental compositions,morphological,and optical properties of the AlZnO@CBMs composites were investigated.Experimental results revealed that two of AlZnO@CBMs composites exhibited superior bleaching efficiency(100% removal) and photocatalytic stability(three cycles) for 50 μmol/L Methylene Blue(MB) contaminated water after 60 min irradiation in visible light at pH 6.5,0.7% H_2O_2,and 5 g/L inorganic salts.Under optimum conditions,AlZnO@CBMs nanocomposites were employed for the treatment of mixed dyestuffs composed of MB,Methyl Orange(MO),Astrazone Blue FRR(BB 69),and Rhodamine B(RhB) dyes under dark,ultraviolet,visible,and direct sunlight.For mixed dyestuffs,the AlZnO@G achieved the highest dye sorption capacity(60.91 μmol dye stuffs/g) with kinetic rate 8.22 × 10~(-3) min~(-1) in 90 min via multi-layer physisorption(Freundlich isotherm) on graphene sheet.In additions,AlZnO@CN offered the highest photo-kinetic rate(K_(photo)) of～54.1 × 10~(-3) min~(-1)(93.8% after 60 min) under direct sunlight.Furthermore,the selective radical trapping experiment confirmed that the holes and oxidative superoxide radicals are crucial on dyes photodegradation pathway.Owing to their superior performance,AlZnO@G and AlZnO@CN nanocomposites can offer an effective in-situ solar-assisted adsorption/photocatalytic remediation of textile wastewater effluents.     

Recent advances in catalytic decomposition of ozone

Ozone (O₃), as a harmful air pollutant, has been of wide concern. Safe, efficient, and economical O₃ removal methods urgently need to be developed. Catalytic decomposition is the most promising method for O₃ removal, especially at room temperature or even subzero temperatures. Great efforts have been made to develop high-efficiency catalysts for O₃ decomposition that can operate at low temperatures, high space velocity and high humidity. First, this review describes the general reaction mechanism of O₃ decomposition on noble metal and transition metal oxide catalysts. Then, progress on the O₃ decomposition performance of various catalysts in the past 30 years is summarized in detail. The main focus is the O₃ decomposition performance of manganese oxides, which are divided into supported manganese oxides and non-supported manganese oxides. Methods to improve the activity, stability, and humidity resistance of manganese oxide catalysts for O₃ decomposition are also summarized. The deactivation mechanisms of manganese oxides under dry and humid conditions are discussed. The O₃ decomposition performance of monolithic catalysts is also summarized from the perspective of industrial applications. Finally, the future development directions and prospects of O₃ catalytic decomposition technology are put forward.     

精神活性物质在北京市某污水处理厂中的污染特征与生态风险

为了解污水处理厂对精神活性物质的去除特征及总出水对受纳水体的生态风险,采用固相萃取-高效液相色谱-串联质谱法调查了北京市某污水处理厂中13种精神活性物质的浓度水平与负荷量变化,并运用RQ（risk quotient,风险熵）对总出水中精神活性物质进行风险评估.结果表明:①13种精神活性物质在总进水与总出水中均能检出,总质量浓度平均值分别为2 395.10和63.59 ng/L,其中ρ（EPH）（EPH表示麻黄碱）占比分别为93.9%和67.9%,其次为COD（可待因）与METH（甲基苯丙胺）.污水处理厂上游地表水中ρ（EPH）、ρ（METH）与ρ（KET）（KET为氯胺酮）均高于总出水及其下游地表水,说明上游沿河可能有新的污染源输入.②污水处理厂对NK（去甲氯胺酮）、BE（苯甲酰爱康宁）和MTD（美沙酮）均呈负去除,其他精神活性物质的去除主要发生在二级生物处理与三级处理（超滤膜与UV消毒）阶段.③污水处理厂服务区域内精神活性物质的周内负荷量存在一定波动,AMP（苯丙胺）、METH、MDA（3,4-亚甲二氧基苯丙胺）、MDMA（3,4-亚甲二氧基甲基苯丙胺）、KET与HER（海洛因）的负荷量均在周末升高.④污水处理厂总出水中精神活性物质的生态风险均较低（RQ < 0.10）.研究显示,污水处理厂不能完全去除污水中的精神活性物质,总出水中残留精神活性物质对受纳河流生态系统产生的长期混合效应不容忽视.      

On-going nitrification in chloraminated drinking water distribution system (DWDS) is conditioned by hydraulics and disinfection strategies

Within the drinking water distribution system (DWDS) using chloramine as disinfectant, nitrification caused by nitrifying bacteria is increasingly becoming a concern as it poses a great challenge for maintaining water quality. To investigate efficient control strategies, operational conditions including hydraulic regimes and disinfectant scenarios were controlled within a flow cell experimental facility. Two test phases were conducted to investigate the effects on the extent of nitrification of three flow rates (Q = 2, 6, and 10 L/min) and four disinfection scenarios (total Cl₂=1 mg/L, Cl₂/NH₃-N=3:1; total Cl₂=1 mg/L, Cl₂/NH₃-N=5:1; total Cl₂=5 mg/L, Cl₂/NH₃-N=3:1; and total Cl₂=5 mg/L, Cl₂/NH₃-N=5:1). Physico-chemical parameters and nitrification indicators were monitored during the tests. The characteristics of biofilm extracellular polymetric substance (EPS) were evaluated after the experiment. The main results from the study indicate that nitrification is affected by hydraulic conditions and the process tends to be severe when the fluid flow transforms from laminar to turbulent (2300<Re<4000). Increasing disinfectant concentration and optimizing Cl₂/NH₃-N mass ratio were found to inhibit nitrification to some extend when the system was running at turbulent condition (Q = 10 L/min, Re = 5535). EPS extracted from biofilm that was established at the flow rate of 6 L/min had greater carbohydrate/protein ratio. Furthermore, several nitrification indicators were evaluated for their prediction efficiency and the results suggest that the change of nitrite, together with total organic carbon (TOC) and turbidity can indicate nitrification potential efficiently.