池塘残饵对底泥氮、磷释放影响的模拟研究

运用室内静态模拟的方法,设置静态释放组(A组)和饲料添加组(B组),研究了池塘残饵分解对底泥氮、磷释放的影响.结果表明,A组DO高于B组(P<0.05),A组pH值为中性,B组pH值呈弱酸性.添加饲料后,B组硝态氮低于A组(P<0.05),而B组活性磷高于A组(P<0.05).实验第2~14 d,A组氨氮高于B组(P<0.05),此后B组氨氮升高,实验结束时B组氨氮高于A组(P<0.05).研究表明,添加饲料的B组,初期氨氮和硝态氮的释放都受到抑制.静态释放的A组,氮的释放变化是先上升,后降低的趋势,而饲料添加的B组,氮的释放变化趋势则是先降低,后升高.B组饲料分解向上覆水释放大量的磷,活性磷的变化呈现先上升后下降的趋势.     

滇西北剑湖沉积物磷形态、空间分布及释放贡献

采用连续分级提取法提取了剑湖沉积物中弱吸附态磷(NH_4Cl-P)、可还原态磷(BD-P)、铁铝氧化态磷(NaOH-rP)、有机质结合态磷(NaOH-nrP)、钙结合态磷(HCl-P)和残渣态磷(Res-P)6种形态的磷,并对表层(0~10 cm)沉积物磷形态水平空间分布、沉积柱芯(0~75 cm)磷形态垂向空间分布和释放贡献特征进行了分析.结果表明:表层沉积物6种磷形态平均含量差别较大,其含量由高到低排序为HCl-PRes-PNaOH-rPNaOH-nrPBD-PNH_4Cl-P;HCl-P含量是NH_4Cl-P的72倍,3种稳定磷形态(HCl-P、Res-P和NaOH-rP)含量是3种潜在可移动磷形态(NaOH-nrP、BD-P和NH_4Cl-P)含量的6.5倍.NH_4Cl-P、BD-P、NaOH-nrP和NaOH-rP含量的变异系数明显高于HCl-P和Res-P含量的变异系数.尽管表层沉积物6种磷形态的水平空间分布特征不尽相同,4条主要入湖河流入湖口区6种磷形态含量平均值之和是湖周浅水区的1.40倍,但能指示出入湖河流是外源磷污染物输入的主要通道.虽然沉积柱芯6种磷形态垂向空间分布特征各异,6种磷形态入湖口区表层平均含量分别是底层的1.60、1.87、1.87、1.61、1.18和1.15倍,其他湖区表层平均含量分别是底层的1.18、1.34、1.39、1.41、0.97和0.83倍,但除HCl-P和Res-P在其他湖区为随深度增加而缓慢递增外,基本上能反映出6种磷形态含量在入湖口区随深度增加而递减的程度都远强于其他湖区.外源磷输入和人为活动影响是3种潜在可移动磷形态和NaOH-rP的主要因素,流域地质背景是HCl-P和Res-P的主要影响因素.6种磷形态在入湖口区快释放贡献率多为负值,表示以滞留状态为主,慢释放贡献率全为正值,表示都为释放状态,滞留贡献最大和释放贡献最大的都是NaOH-rP;其他湖区快释放贡献率和慢释放贡献率多为正值,表示都以释放状态为主,NaOH-rP释放贡献最大,Res-P滞留贡献最大.     

南水北调对密云水库水位变幅带土壤磷释放量的影响

南水北调来水引起的水位上涨可能会导致密云水库水位变幅带土壤中磷的释放.过量的磷可能会引起水体富营养,因此,研究水库变幅带磷释放风险对密云水库水质安全保障具有科学指导意义.本研究采用连续浸提法测定密云水库变幅带土壤及沉积物中弱吸附态磷(NH_4ClP)、铁磷(BD-P)、铝磷(NaOH-P)及钙磷(HCl-P)等4种不同形态磷含量,探讨其分布特征;并在室内进行了磷释放模拟实验,估算了南水北调来水引起水库水位上升所致的易释放磷的释放量.结果表明,NH_4Cl-P、BD-P、NaOH-P、HCl-P广泛地分布于密云水库变幅带土壤及沉积物中.在白河、内湖及潮河3个库区,磷形态分布具有一致规律,即HCl-PNaOH-PBD-PNH_4Cl-P.因密云水库变幅带为中国典型的北方碱性土壤,变幅带无机磷主要为钙磷.NH_4Cl-P在3个库区变幅带土壤中含量相差不大,在受水动扰动力影响较小的内湖库区BD-P含量略高于其它2个库区.在3个不同库区中,潜在活性磷NH_4Cl-P和较稳定的NaOH-P在岸上和水陆交界面土壤及水下沉积物中含量相差不大,受氧化还原条件影响较大的BD-P在沉积物中的含量略高于岸上和水陆交界面土壤.磷释放模拟实验及释放量估算结果表明,水库水位上涨3 m的情况下,白河、潮河和内湖库区淹没变幅带土壤分别释放1.02、0.80、0.37 mg·m~(-2)易释放磷.白河和内湖库区变幅带被水淹没土壤中磷释放的风险可能更高,需加强防护.     

An overview of the latest development of microencapsulation for agricultural products

Abstract

For the production of controlled‐release agricultural formulations microencapsulation technologies are now the most used. Over the past two decades enormous progress has been made in order to develop the technologies which allow us to produce formulations tailor made to reach the target and fitting our toxicological requirements. This lecture is devoted to the definition of the criteria for selection of an active ingredient for microencapsulation and to a detailed review of the various techniques used today in commerçai microencapsulated formulations.

Resources are increasingly allocated into microencapsulation research & development by many agrochemical companies. Therefore the next 20 years should continue to yield innovative ideas including significant improvement of the physico‐chemical and toxicological properties of the actual formulations on the market. Some of this new ideas are applied by our company in order to modify or improve those properties playing the key role in the intent for targeted activity:

√ Recombination during production or upon storage.

New protective colloides

Dermal toxicity (LD 50) ‐ secondary protective colloides.

√ Release rate parameters.

Modification by the change of mobility of the active ingredient from the core (solvent or fluid type) affecting transit time and therefore LD 50 values.

√ Oral toxicity (LD 50).

Graft copolymers irreversibly adsorbed to the capsule surface.     

Accidental release: Fuzzy selection of adequate formal model

Risk assessment of a chemical process plant requires the application of a variety of consequence models in order to estimate the potential physical effects of accidental releases. The types of models required vary depending upon the substance under consideration and the circumstances of a release. The objective of this study was the development and application of a system based upon ‘fuzzy logic’, for the selection of a computer model to be used in consequence analysis in specific situations where only certain types of consequence models can be used. The collection of data for modelling purposes from different kinds of computer model and application of fuzzy methods were also important aims of the study.     

Investigation the effect of adding graphene oxide into diesel/higher alcohols blends on a diesel engine performance

ABSTRACT

This article aims to study the influence of the addition of graphene oxide nanoparticles (GO) to diesel/higher alcohols blends on the combustion, emission, and exergy parameters of a CI engine under various engine loads. The higher alcohols mainly n-butanol, n-heptanol, and n-octanol are blended with diesel at a volume fraction of 50%. Then, the 25 and 50 mg/L concentrations of GO are dispersed into diesel/higher alcohols blends using an ultrasonicator. The GO structures are examined using TEM, TGA, XRD and FTIR. The findings show that there is a reduction in p_max. and HRR when adding higher alcohols with diesel fuel. Regarding engine emission, there is a significant improvement in emissions formation with adding higher alcohols. The addition of GO into diesel/higher alcohols blends improves the brake thermal efficiency by 15%. Moreover, the p_max. and HRR are both enhanced by 4%. The CO, UHC and smoke formation are reduced considerably by 40%, 50 and 20%, respectively, while NO_x level is increased by 30% with adding GO. Finally, adding high percentages of n-butanol, n-heptanol, and n-octanol with diesel fuel with the presence of GO has the potential to achieve ultra-low CO, UHC, and smoke formation meanwhile keeping high thermal efficiency level.     

潮湿巷道风流温度与湿度变化规律分析

通过对矿井风流与围岩热湿交换理论的研究,提出理论上更可靠的风流温、湿度计算方法,编制了模拟解算矿井风流与围岩热湿交换的计算机程序,解算出潮湿巷道风流温度及湿度的变化规律,并分析通风时间、湿度系数等参数对风流温度及湿度变化规律的影响;沿风流流动方向,风流温度及湿度不断增加;巷道风流温度及湿度随着通风时间的增加而不断减小,通风时间越长减小的幅度越小;围岩壁面湿度系数对风流温度及湿度的影响较大,其他参数不变时,壁面湿度系数越大,风流温度越小,风流湿度越大。     

液化四氟乙烷小孔泄漏试验研究

采用高速摄影技术,考察了液化四氟乙烷发生小孔泄漏时,其水平泄漏和垂直泄漏的初始云团演化行为、泄漏的质量流率、喷射速度和喷射角,并与理论计算公式进行了对比。结果表明:水平喷射两相云团尾部出现涡流,涡流大幅加快了云团向空气中扩散的速率;垂直喷射的两相云团在地面形成液池,液池大幅增加了液化气体向空气中蒸发的速率。水平泄漏试验的喷射角与容器内超压变化规律相似,泄放初期喷射角逐渐增大,经历一段平坦期,到泄放末期喷射角减小。水平泄漏和垂直泄漏的初始喷射速度分别为25 m/s和20 m/s,与理论值26.6 m/s基本吻合。水平泄漏的质量流率的试验值和理论值分别为0.0598 kg/s和0.0684 kg/s,垂直泄漏的分别为0.0472 kg/s和0.059 6 kg/s,结果对比基本吻合,推荐的泄漏质量流率和小孔喷射速度公式可以用于液化四氟乙烷小孔泄漏。     

烧结砖中重金属释放特性研究

通过向黏土中添加重金属试剂,模拟煅烧试验制作烧结砖.采用酸消解试验研究烧结砖中重金属的总量,采用欧盟NEN7371方法测试烧结砖中重金属的有效释放量,采用NEN7375方法进行块状烧结砖浸出试验,研究烧结砖样品中Cr、Ni、As、Cd和Pb的释放特性.结果表明:烧结砖中重金属的有效释放量低于总量,释放率从大到小为Cd、As、Pb、Ni、Cr;在块状浸出过程中,Cr、Ni、As累积释放量达到平衡的时间为16 d,Pb为4d,而Cd的累积释放量一直有上升的趋势;Cr、Ni、As的释放机理主要为扩散控制,Cd为溶解作用,Pb为表面冲刷作用;5种重金属释放速率从大到小为Ni、Cr、Pb、As、Cd.     

不同pH值对磷矿废石磷素浸出特性影响的实验研究

采用EPA 1314pH酸碱预滴定实验和pH浸出实验,研究了pH对磷矿废石磷元素浸出特性的影响,以及磷矿废石的酸碱缓冲容量。实验结果表明:磷矿废石的碱缓冲容量小,pH从8.75上升到13.50消耗了0.1mmol/g的NaOH,磷矿废石酸的缓冲容量较大,pH从5.50到1.00,共消耗2.2mmol/g的H2SO4;浸提液的酸碱性是影响磷矿废石中磷元素浸出的重要参数,酸性条件下很大程度上促进了磷元素的浸出,随着H+离子浓度的增加,总磷浓度随之升高。相反在碱性条件下的反应过程中,OH-阻碍磷元素的浸出,消耗正磷酸根离子和羟基磷酸根离子,使其生成沉淀,有一定的固磷作用,为磷元素的固化提供了更多途径。