厌氧-好氧一体化反应器处理高浓度有机废水的运行特性研究

本实验采用新型厌氧—好氧一体化反应器处理高浓度有机废水,主要研究了系统的启动与运行性能,并对系统的NH3 N去除效果作了初步考察。实验结果表明:在16℃～24℃的自然温度下,采用递增负荷、厌氧和好氧分期启动的方式,系统可在38天内达到较好的启动效果;在系统负荷运行期内,当系统总进水COD浓度平均值为3601 8mg/L,总出水COD浓度平均值为384 0mg/L,系统容积负荷平均值为2 54kgCOD/(m3·d),系统总HRT平均值为35 1h时,系统总COD去除率平均值达90 6%。实验还发现:当进水NH3 N浓度为280 3～350 7mg/L,整个系统的NH3 N去除率在68 5%～91 7%,平均为81 0%。由此说明,本反应器具有很好的COD去除性能和NH3 N去除效果,适合于处理COD浓度高且含有中等NH3 N浓度的有机废水。     

垃圾焚烧飞灰中重金属的固化/稳定化处理实验研究

研究了城市生活垃圾焚烧-电灰的特性及飞灰中重金属的特性,对利用水泥作粘结剂进行飞灰固化/稳定化处理效果开展了系统的实验研究,分析了水泥固化/稳定化飞灰的工艺特点和最佳工艺参数,并讨论了粘结剂固化飞灰机理以及重金属浸出毒性,为进一步研究城市生活垃圾焚烧飞灰的无害化处理与利用提供了有重要价值的参考依据.     

Using multivariate regression modeling for sampling and predicting chemical characteristics of mixed waste in old landfills

Municipal solid waste landfills pose a threat on environment and human health, especially old landfills which lack facilities for collection and treatment of landfill gas and leachate. Consequently, missing information about emission flows prevent site-specific environmental risk assessments. To overcome this gap, the combination of waste sampling and analysis with statistical modeling is one option for estimating present and future emission potentials. Optimizing the tradeoff between investigation costs and reliable results requires knowledge about both: the number of samples to be taken and variables to be analyzed.This article aims to identify the optimized number of waste samples and variables in order to predict a larger set of variables. Therefore, we introduce a multivariate linear regression model and tested the applicability by usage of two case studies. Landfill A was used to set up and calibrate the model based on 50 waste samples and twelve variables. The calibrated model was applied to Landfill B including 36 waste samples and twelve variables with four predictor variables.The case study results are twofold: first, the reliable and accurate prediction of the twelve variables can be achieved with the knowledge of four predictor variables (Loi, EC, pH and Cl). For the second Landfill B, only ten full measurements would be needed for a reliable prediction of most response variables. The four predictor variables would exhibit comparably low analytical costs in comparison to the full set of measurements. This cost reduction could be used to increase the number of samples yielding an improved understanding of the spatial waste heterogeneity in landfills.Concluding, the future application of the developed model potentially improves the reliability of predicted emission potentials. The model could become a standard screening tool for old landfills if its applicability and reliability would be tested in additional case studies.     

生物滴滤塔处理氯苯废气的工艺性能

将活性污泥培养及驯化后接种于生物滴滤塔中，挂膜启动后处理模拟氯苯废气（简称氯苯废气），考察了生物滴滤塔在挂膜启动阶段及稳定运行阶段的性能。实验结果表明：接种41 d后生物滴滤塔成功挂膜，此时氯苯去除率稳定在90%以上；生物滴滤塔稳定运行阶段，随着进气中氯苯质量浓度由303.82 mg/m³逐渐增至1 489.05 mg/m³，氯苯去除率从85.1%降至70.1%。处理氯苯废气适宜的工艺条件为：空塔停留时间超过45 s，喷淋液流量31.8 mL/min，氯苯负荷23.97~128.01 g/（m³·h）。生物滴滤塔对喷淋液的酸性环境有较好的适应性，喷淋液pH的变化对氯苯去除率无显著影响。     

Selective collection as a pretreatment for indirect solid recovered fuel generation

Effective selective collection (SC) has been increasing in many countries of the European Union. As a consequence the composition of residual municipal solid waste (RMSW) is changing not only because of economic development, but also due to the collection system. The input of RMSW treatment plants is thus not homogeneous. This paper analyses two case studies involving a total of five SC scenarios and their impact on the generation of solid recovered fuel (SRF) with/without bio-drying, post-treatment and packaging take back programs (TBPs). These case studies are based on two types of SC: kerbside and drop-off. The latest regulation on SRF classification is taken into account: energy content, Cl and Hg concentrations are assessed and discussed. The role of the respirometric index (RI) is also analyzed. Results show that when SC is highly efficient RMSW can be classified directly as SRF, but only if the introduction of RI does not set stringent respirometric targets. The role of packaging TBPs is important as the residual waste remaining after the packaging has been processed, can be valorized increasing the lower heating value (LHV) of the residual RMSW and minimizing the streams that should be landfilled. The source separation of food waste has a significant impact on the suitability of bio-drying: when the SC of food waste is very efficient, its percentage in the RMSW may be too low for effective bio-drying.     

Determination of Au(III) and Pd(II) ions by flame atomic absorption spectrometry in some environmental samples after solid phase extraction

A simple and sensitive solid phase extraction method was developed for simultaneous separation and preconcentration of gold and palladium ions with N-(4-methylphenyl)-2-{[(4-phenyl-5-pyridine-4-yl-4H-1,2,4-triazol-3-yl)thio]acetyl}hydrazine carbo thioamide complex on Amberlite XAD-1180 resin before their determination by flame atomic absorption spectrometry. Some analytical parameters such as HNO₃ concentration of the sample solution, amount of complexing agent, sample volume, eluent type and volume, effects of foreign ions and adsorption capacity of the resin were investigated for quantitative recovery of gold and palladium ions. The effects of some anions and cations were also examined. Under optimum conditions, the detection limits for gold and palladium ions were found to be 0.29 and 0.19 μg L^?1, respectively. The preconcentration factor for gold and palladium was 250. After being validated by standard addition and analysis of standard reference material, the procedure was successfully applied to the analysis of sea and stream water, anodic slime, gold ore, soil and electronic waste.     

Pyrolysis technologies for municipal solid waste: A review

Pyrolysis has been examined as an attractive alternative to incineration for municipal solid waste (MSW) disposal that allows energy and resource recovery; however, it has seldom been applied independently with the output of pyrolysis products as end products. This review addresses the state-of-the-art of MSW pyrolysis in regards to its technologies and reactors, products and environmental impacts. In this review, first, the influence of important operating parameters such as final temperature, heating rate (HR) and residence time in the reaction zone on the pyrolysis behaviours and products is reviewed; then the pyrolysis technologies and reactors adopted in literatures and scale-up plants are evaluated. Third, the yields and main properties of the pyrolytic products from individual MSW components, refuse-derived fuel (RDF) made from MSW, and MSW are summarised. In the fourth section, in addition to emissions from pyrolysis processes, such as HCl, SO₂ and NH₃, contaminants in the products, including PCDD/F and heavy metals, are also reviewed, and available measures for improving the environmental impacts of pyrolysis are surveyed. It can be concluded that the single pyrolysis process is an effective waste-to-energy convertor but is not a guaranteed clean solution for MSW disposal. Based on this information, the prospects of applying pyrolysis technologies to dealing with MSW are evaluated and suggested.     

顶空固相微萃取-气相色谱法测定水中氯苯类化合物

采用顶空固相微萃取（HS －SPME）技术萃取水中6种氯苯类化合物，全面分析对目标物萃取效率的影响因素，并确定萃取试验的最佳条件。用顶空固相微萃取联合气相色谱法（HS －SPME －GC）测定水中6种氯苯类化合物，方法在0.500 ng／L～2.00×10^5 ng／L范围内线性良好，检出限为0.05 ng／L ～2000 ng／L，空白样品加标回收率为69.8％～121％， RSD为4.8％～18.3％。用该方法测定实际水样，平行双样的相对偏差低于20％。     

固体废物全过程管理中固体废物鉴别研究

对固体废物应进行全过程管理,固体废物鉴别是固体废物全过程管理的基础和关键,包括依据产生来源鉴别和过程鉴别两种方法,依据产生来源鉴别包括丧失原有利用价值的物质、在生产过程中产生的副产物、环境治理和污染控制过程中产生的物质、其他物质四类,在每一类中详细地列举了属于该产生来源的具体固体废物种类名称,便于理解和增强可操作性。过程鉴别包括在固体废物再生利用过程和处置过程中的固体废物鉴别两类,其中在再生利用过程的固体废物鉴别中明确指出了固体废物再生利用产物只有同时满足产品质量标准要求、国家污染控制标准要求以及有实际市场需求、固定用户等条件时,才不作为固体废物管理,在处置过程的固体废物鉴别中具体地列出了处置固体废物全过程中仍然作为固体废物管理的国际惯用处置方式。同时,给出了清晰的"原料—产品—固体废物—处置或产品"全过程中固体废物的产生节点和相应的固体废物类别图,为固体废物鉴别工作提供参考,使固体废物全过程管理有的放矢,有效防止固体废物对环境和人体健康造成的危害。     

Emergency shutdown of fluidized bed reaction systems

With several industrial applications of fluidized bed technology recently commercialized worldwide, it becomes essential to develop safe operation methods for fluidized bed reaction systems (FBRSs) to prevent any influence on their process values, which lead to accidents. To preventing any disaster or malfunction in an FBRS, an emergency shutdown system (ESD) is initiated, closing the reaction system in case of any abnormality by effectively isolating the flammable gas. However, an ESD is also prone to the “inactivation problem,” in which in the case of failure it initiates the emergency shutdown, even when the operating conditions of the reaction system are abnormal. It is also vulnerable to a “malfunction problem,” where the emergency shutdown is performed even when the operating conditions of the reaction system are normal. In this study, these problems were solved by investigating a reaction system through the monitoring of appropriate parameters and setting up of trigger levels, which reflect the uniqueness of an FBRS using an ESD. The parameters were identified by analyzing the scenario leading to an accident. The trigger levels were determined as the points at which the loss is smaller in the presence of an ESD, as compared to the value of the loss function in the presence or absence of an ESD. Furthermore, the ESD design model was applied as a case study in the ammoxidation process of propylene. The results showed that an ESD can prevent an approximately 8 billion yen of loss due to accidents in plant operations, against an investment of 200 million yen.