San copolymer membranes with ion exchangers for Cu(II) removal from synthetic wastewater by electrodialysis

Heterogeneous membranes were obtained by using styrene-acrylonitrile copolymer (SAN) blends with low content of ion-exchanger particles (5 wt.%). The membranes obtained by phase inversion were used for the removal of copper ions from synthetic wastewater solutions by electrodialytic separation. The electrodialysis was conducted in a three cell unit, without electrolyte recirculation. The process, under potentiostatic or galvanostatic control, was followed by pH and conductivity measurements in the solution. The electrodialytic performance, evaluated in terms of extraction removal degree (rd) of copper ions, was better under potentiostatic control then by the galvanostatic one and the highest (over 70%) was attained at 8 V. The membrane efficiency at small ion-exchanger load was explained by the migration of resin particles toward the pores surface during the phase inversion. The prepared membranes were characterized by various techniques i.e. optical microscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis and differential thermal analysis and contact angle measurements.     

Closing the water cycle for industrial laundries: An operational performance and techno-economic evaluation of a full-scale membrane bioreactor system

To reduce the consumption of freshwater in the laundry industry, a new trend of closing the water cycle has resulted in the reuse/recycling of water. In this study, the performance of a full-scale submerged aerobic membrane bioreactor (9 m³) used to treat/reuse industrial laundry wastewater was examined over a period of 288 days. The turbidity and total solids (TS) were reduced by 99%, and the chemical oxygen demand (COD) effluent removal efficiencies were between 70% and 99%. The levels of COD removed by the membrane were significantly greater than the levels of biodegraded COD. This enabled the bioreactor to sustain COD levels that were below 100 mg/L, even during periods of low wastewater biodegradation due to bioreactor sludge. An economic evaluation of the membrane bioreactor (MBR) system showed a savings of 1.13 € per 1 m³ of water. The payback period for this system is approximately 6 years. The energy and maintenance costs represent only 5% of the total cost of the MBR system.     

Removal of tetrabromobisphenol A by conventional activated sludge, submerged membrane and membrane aerated biofilm reactors

The goal of this study was to compare removal efficiencies of tetrabromobisphenol A (TBBPA) using typical wastewater treatment technologies, and to identify the most significant mechanisms of removal. Two types of municipal wastewater reactors were studied: a full-scale conventional activated sludge (CAS) reactor with tertiary treatment; and three pilot-scale membrane bioreactors (MBRs) having different sludge retention times (SRTs). All four reactors were fed the same influent. A third reactor type, a membrane aerated biofilm reactor (MABR) was fed tap water, ammonia, and TBBPA. TBBPA in municipal influent ranged from 1 to 41 ng L⁻¹ (n = 10). The CAS effluent had an average TBBPA concentration of 0.7 ± 1.3 ng L⁻¹ (n = 3). Effluent concentrations from the MBRs were an average of 6 ± 6 ng L⁻¹ TBBPA (n = 26). Significant TBBPA removal was observed in the MABR throughout the 5 week of study (p ? 0.05). Removal of TBBPA from wastewater treatment was found to be due to a combination of adsorption and biological degradation. Based on experimental results, nitrification is likely a key process therein. No significant relationship between removal of TBBPA and SRT was identified (p ? 0.05).     

Isolation and characterization of lead-tolerant Ochrobactrum intermedium and its role in enhancing lead accumulation by Eucalyptus camaldulensis

In this study, the potential of rhizospheric bacteria in promoting the growth and Pb accumulation by the woody plant Eucalyptus camaldulensis under hydroponic conditions was investigated for the first time. Three Pb-tolerant bacteria were isolated from the rhizosphere of E. camaldulensis grown in Pb-contaminated soils in the Bo Ngam Pb mine, Thailand. Based on analysis of partial 16S rRNA gene sequence, the three isolates were identified as Microbacterium paraoxydans BN-2, Ochrobactrum intermedium BN-3, and Bacillus fusiformis BN-4. Among these strains, O. intermedium BN-3 showed the highest tolerance to not only Pb but also Cd and Zn. After growth in the presence of Pb, the membranes of O. intermedium BN-3 cells exhibited an increase in unsaturated fatty acid levels but a decrease in fluidity. In hydroponic studies, inoculation of O. intermedium BN-3 significantly increased the biomass and Pb accumulation by E. camaldulensis compared to the uninoculated control. The results suggested the role of the natural rhizospheric bacteria localized to the root surface of E. camaldulensis in promoting Pb accumulation and plant growth. Our results indicate that O. intermedium BN-3 and other indigenous rhizospheric bacteria have the potential to improve the efficiency of phytoremediation of Pb-contaminated sites.     

Chitosan/albumin/CaCO3 as mimics for membrane bioreactor fouling: genesis of structural mineralized-EPS-building blocks and cake layer compressibility

Membrane bioreactor biofouling is usually described as an extracellular matrix in which biopolymers, inorganic salts and active microbes co-exist. For that reason, biomineralization (BM) models can be useful to describe the spatial organization and environmental constraints within the referred scenario. BM arguments were utilized as background in order to (1) evaluate CaCO₃ influence on flux decline; pore blocking and cake layer properties (resistance, permeability and compressibility) in a wide range of Chitosan/Bovine serum albumin (BSA) mixtures during step-pressure runs and, (2) perform membrane autopsies in order to explore the genesis of mineralized extracellular building blocks (MEBB) during cake layer build up. Using low molecular weight chitosan (LC) and BSA, 2 L of 5 LC/BSA mixtures (0.25-1.85 ratio) were pumped to an external ultra filtration (UF) membrane (23.5 cm², hydrophobic, piezoelectric, 100 kDa as molecular weight cut-off). Eight different pressure steps (40 ± 7 to 540 ± 21 kPa) were applied. Each pressure step was held for 900 s. CaCO₃ was added to LC/BSA mixtures at 0.5, 1.5 and 3 mM in order to create MEBB during the filtration tests. Membrane autopsies were performed after the filtration tests using thermo gravimetric, scanning microscopy and specific membrane mass (mg cm⁻²) analyses. Biopolymer-CaCO₃ step-pressure filtration created compressible cake layers (with inner voids). The formation of an internal skeleton of MEBB may contribute to irreversible fouling consolidation. A hypothesis for MEBB genesis and development was set forth.     

A novel sequence batch membrane carbonation photobioreactor developed for microalgae cultivation

A novel SBM-C-PBR was constructed for microalgae cultivation. Membrane fouling was greatly mitigated by membrane carbonation. NH₄⁺ and P removal rates were around 80% in SBM-C-PBR. Biomass was completely retained by membrane. In this study, a novel sequence batch membrane carbonation photobioreactor was developed for microalgae cultivation. Herein, membrane module was endowed functions as microalgae retention and CO₂ carbonation. The results in the batch experiments expressed that the relatively optimal pore size of membranes was 30 nm, photosynthetically active radiation was 36 W/m² and the CO₂ concentration was 10% (v/v). In long-term cultivation, the microalgal concentration separately accumulated up to 1179.0 mg/L and 1296.4 mg/L in two periods. The concentrations of chlorophyll a, chlorophyll b and carotenoids were increased about 23.2, 14.9 and 6.3 mg/L respectively in period I; meanwhile, the accumulation was about 25.0, 14.5, 6.6 mg/L respectively in the period II. Furthermore, the pH was kept about 5.5–7.5 due to intermittent carbonation mode, which was suitable for the growth of microalgae. Transmembrane pressure (TMP) was only increased by 0.19 and 0.16 bar in the end of periods I and II, respectively. The pure flux recovered to 75%–80% of the original value by only hydraulic cleaning. Scanning electron microscope images also illustrated that carbonation through membrane module could mitigate fouling levels greatly.     

微生物燃料电池的专利技术综述

检索了微生物燃料电池在中国的发明专利文献,综述了微生物燃料电池在废水处理中的应用及与现有技术中其他水处理技术耦合的专利进展,并对其实际应用的前景进行了展望。     

MBR-PAC系统影响因素的研究

向膜生物反应器内投加40 g·L-1粉末活性炭处理尾水,运行效果良好.排泥和水力停留时间对处理效果有很大影响,流量和曝气量在一定程度上决定了膜污染的进程,粉末活性炭吸附降解了一些易引起膜污染的有机物,改变了污泥的性质,使膜通量得到改善.气洗和反冲洗能很好的维持膜通量,离线清洗可使膜通量基本恢复.     

普通活性污泥膜生物反应器处理洗车废水的应用研究

膜生物反应器是近年来发展起来的一种新型高效水处理设备。它将分离工程中的膜技术应用于好氧活性污泥处理系统，由膜组件取代传统生化处理技术中的二次沉淀池和砂滤池，由膜分离技术代替传统方法中的重力式沉淀泥水分离技术方式，具有简洁、高效等优点。采用普通活性污泥膜生物反应器工艺对天津某一洗车点洗车废水进行处理，并将处理出水回用于洗车。     

曝气强度对膜污染的影响

混合液浓度的高低及其粒度分布特性是影响膜生物反应器膜污染的重要因素。在一定污泥浓度下,主要考察了曝气强度对污泥絮体粒度分布的影响,以及不同粒度下的膜污染特性。试验结果表明,曝气强度提高,可以起到减缓污泥颗粒在膜表面的沉积作用,但高的错流流速产生的剪切效应使得污泥颗粒变得琐碎,导致细小胶体粒子和溶解性部分增多,增加了膜孔吸附和堵塞的机会,加剧了膜污染的进程。膜污染速率在曝气强度提高初期阶段迅速降低,接着又随曝气强度增加而缓慢升高,在污泥质量浓度为8 g/L的试验条件下,对应的最适曝气强度为84 m3/(m2.h)。