颗粒冲蚀对注射法制备C/C-ZrC-SiC复合材料 抗烧蚀性能的影响研究

目的采用ZrC和SiC复相陶瓷对C/C复合材料进行改性,研究改性后的复合材料受到颗粒冲蚀破坏的烧蚀行为。方法采用注射法将ZrC和SiC复相陶瓷前驱体引入到等温化学气相渗透法(ICVI)制备的低密度C/C复合材料中,再通过高温热处理、ICVI的方法制备出ZrC和SiC复相陶瓷改性的C/C(C/C-ZrC-SiC)复合材料,随后对制备的复合材料进行高速颗粒冲击实验破坏,并对破坏后的试样进行氧乙炔火焰烧蚀,研究其烧蚀行为。结果改性后的复合材料线冲蚀率和质量冲蚀率分别为253.1μm/s和79.8 mg/s,相较于同孔隙率的C/C复合材料分别降低了49.2%和61%。颗粒冲蚀破坏后C/C-ZrC-SiC复合材料的线烧蚀率和质量烧蚀率分别为4.26μm/s和1.44 mg/s,相比于同孔隙率的C/C复合材料,分别降低了37%和39%。结论由于引入的ZrC和SiC陶瓷相的硬度大于碳基体,C/C-ZrC-SiC复合材料在受到高速颗粒的冲击时,能通过硬质陶瓷相起到抗冲击作用,使得改性后的复合材料抗冲蚀性能大幅度提高。受到颗粒冲蚀破坏后的C/C-ZrC-SiC复合材料内部仍存在超高温陶瓷相,烧蚀过程中能够形成ZrO2骨架结构和SiO2球形颗粒,进而有效保护碳纤维和热解碳基体。     

Processing and Characterization of Short-Fiber Reinforced Jute/Poly Butylene Succinate Biodegradable Composites: The Effect of Weld-Line

Fabrication of complex injection molded parts often involves the use of multiple gates. In such situations, polymer melts from different gates meld to form the molded part (weld line). This paper reports on the fabrication and characterization of the mechanical and morphological properties of short fiber reinforced jute/poly butylene succinate (PBS) biodegradable composites. The effect of a dual gated mold in the fabrication of welded specimens was a key focus of the investigation. It was observed that incorporation of jute fiber (10 wt%) conferred drastic changes on the stress–strain properties of the matrix as the elongation at break (EB), dropped from 160% in the matrix to just 10% in the composite. The tensile strength of the composite was lower than that of the matrix. However, it is noteworthy that the tensile modulus of the composite increased. Bending test also revealed that both bending strength and modulus increased with the incorporation of jute. Morphological studies of the tensile fracture surface using SEM revealed two types of failure mode. Ductile failure was indicated by plastic deformation at the initiation of fracture followed by brittle failure. The good interfacial bonding indicated between jute and PBS was attributed to positive interaction between the two polar polymers. A comparison of the non-weld and weld-line samples revealed that the weld-line composites have better mechanical integrity than the corresponding polymer matrix with weld line. The results also revealed that elongation at break and toughness are most sensitive to the presence of the weld-line whereas flexural properties are least sensitive.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

气-固复合粉体在高原地区灭火性能的试验研究

为满足高原地区低压低氧环境对火灾防治的特殊需求,在拉萨进行模拟试验,研究由溴氟丙烯和13X沸石所组成的气-固复合粉体灭火剂对汽油火的灭火性能,并与平原地区的合肥的灭火效果进行对比。试验结果表明,在拉萨低压低氧的环境下,复合粉体灭火剂对汽油火具有很好的灭火性能。在同样的试验条件下,其灭火时间和灭火剂用量比合肥减少20%以上,说明该复合粉体灭火剂在高原地区有很好的适用性。     

高锰酸盐复合剂强化饮用水除污染生产性研究

采用依时间序列进行对比的方法，考察了高锰酸盐复合剂(PPC)对饮用水源的强化除污染效能。生产性实验结果表明，PPC具有优良的强化混凝和强化过滤效能，能显著降低水厂沉后水和滤后水的浊度、COD_Mn、UV₂₅₄等水质指标。与未投加时相比较，水厂投加PPC后沉后水和滤后水浊度分别降低了25%和33.3%，沉后水和滤后水COD_Mn去除率分别提高了15.3%和11.5%，UV₂₅₄去除率分别提高了16.3%和9.5%。同时，GC/MS分析表明PPC能有效去除水源水中的多种微量有机污染物，显著提高饮用水的化学安全性。PPC通过高锰酸钾的氧化作用，水合二氧化锰的吸附作用，以及各组分间的协同强化作用，显著提高了对水中污染物质的去除效率。     

高锰酸盐复合药剂预氧化缓解超滤膜藻类污染的中试研究

通过中试试验考察了高锰酸盐复合药剂(PPC)预氧化强化混凝/沉淀/超滤的组合工艺的除藻效能以及PPC预氧化对藻类引起的膜污染的缓解作用,并对其机理进行了探讨.试验结果表明,投加0.6mg·L-1PPC能使预处理阶段对藻类的平均去除率提高约28%.组合工艺处理高藻水时,PPC预氧化通过强化预处理,降低膜表面的污染负荷,对藻源污染物引起可逆和不可逆污染均具有一定的缓解作用.化学清洗试验结果表明,碱洗对超滤膜TMP恢复效果远远强于酸洗,因而有机物是超滤膜处理高藻水时的主要污染物质.     

RGO/TiO2光催化降解2,4-二氯苯氧乙酸研究

通过Hummers法及紫外光/热还原工艺制得还原氧化石墨烯(RGO),采用溶胶-凝胶-煅烧法,以RGO和钛酸酊脂为前驱体制备出RGO/TiO2光催化复合材料,并利用XRD、FT-IR等对其进行了表征.对RGO/TiO2光催化降解性能的研究发现,复合光催化剂RGO/TiO2对2,4-二氯苯氧乙酸(2,4-D)的光催化降解活性显著优于纯TiO2,并且发现负载量和pH值对光催化降解性能有较大的影响:RGO/TiO2投加量为1.2g·L~(-1)、RGO负载量2%、pH为3、初始浓度为50 mg·L~(-1)反应12 h,2,4-D去除率达到98.75%;2,4-D降解率随着RGO/TiO2投加量的增大先增大后减小;RGO/TiO2对2,4-D的降解为脱氯还原和催化氧化过程,产生氯酚、苯酚等中间产物.     

Cf/SiC 复合材料表面 HfO2涂层的制备及其抗热冲击性能研究

目的研究等离子喷涂条件下Cf/SiC复合材料表面HfO_2涂层的物相、显微组织及其抗热冲击性能。方法通过水热合成和喷雾造粒制备出HfO_2粉体,并利用等离子喷涂在Cf/SiC复合材料表面制备HfO_2涂层,研究涂层的物相、显微组织和抗热冲击性能。结果水热合成的纳米HfO_2为单斜相结构,颗粒的平均粒径为10~15nm;等离子喷涂制备的HfO_2涂层组织中存在微裂纹和孔隙,涂层为单斜相结构,且经1350℃热处理后涂层的相结构未发生改变。等离子喷涂的HfO_2涂层与Cf/SiC复合材料基体结合良好,未观察到涂层、基体间界面分离的现象。经1350℃、50周次的空冷热冲击试验后,涂层未发生破坏失效;在1350℃水冷热冲击条件下,热循环20次时涂层表面出现剥落,27次时脱落面积50%。结论通过等离子喷涂制备的HfO_2涂层与Cf/SiC复合材料基体结合良好,涂层能够抵御1350℃空冷、50周次热冲击,且未发生破坏失效,涂层的1350℃水冷热循环寿命达27次。     

基于复配改性木质素磺酸铵的环保型木质材料的生命周期评价

利用改性木质素制备的木质材料其生产过程对生态环境有重要的影响.为探讨该环保型木质材料的可行性,利用Ga Bi 6.0软件,对基于复配改性木质素磺酸铵的环保型木质材料(HMIL/WF)进行生命周期评价,比较分析生命周期各生产环节的非生物资源耗竭、酸化效应、富营养化、全球变暖潜值、臭氧层破坏潜能以及光化学臭氧生成潜力等主要环境影响类型.结果表明:在HMIL/WF材料生命周期的3个子系统中,纤维制造子系统对各环境影响贡献值最大,此次是产品成型子系统,后期加工子系统对环境影响最小.全球变暖潜值是HMIL/WF材料环境影响的主要类型,占总环境影响值的73.09%,环境影响大小依次为全球变暖潜值、酸化效应、光化学臭氧生成潜力、富营养化、非生物资源耗竭和臭氧层破坏潜能.热能消耗的环境影响最为严重,占HMIL/WF材料生命周期总环境影响的44.77%.各生产环节的环境影响大小顺序依次为热能消耗、电能消耗、H_2O_2生产、木质素磺酸铵(AL)制备和运输阶段.热能消耗环节的全球变暖潜值、酸化效应、光化学臭氧生成潜力、富营养化和非生物资源耗竭的影响值为HMIL/WF材料生产各环节的最高值;运输阶段产生了最高的臭氧层破坏潜能.与传统中密度纤维板的生命周期环境影响潜值总值(4.71×10~(-9))相比,HMIL/WF材料的环境影响总值(4.22×10~(-9))减少了10.4%.     

石墨基复合材料负载零价纳米铁吸附重金属离子的研究进展

工业废水中重金属的存在威胁着环境和人类健康,有效去除环境中的重金属离子具有重要意义.论文简要介绍了近年来石墨基复合材料负载纳米零价铁(nZVI)去除废水中重金属离子的研究,探讨了多种石墨基负载nZVI复合材料对重金属离子的吸附特性和环境条件对吸附性能的影响因素,并对其未来的研究和应用进行了总结和展望.