雷达吸波复合材料外观失效机理分析及控制方法研究

目的 解决多层泡沫夹芯结构的雷达吸波复合材料在环境效应下产生外观失效的问题。方法 制备3种类型的雷达吸波复合材料,开展典型自然环境试验。观察试验样品外观状态,并检测变形量。通过观察泡沫的微观组织形貌,检测热膨胀量变化及泡沫与树脂间的粘黏强度,用气相色谱质谱联用仪GCMS检测复合材料裂解气体成分,分析复合材料外观失效成因,并提出解决技术途径。结果 6个月自然环境试验后,1#、2#样品外观失效,而3#样品无明显变化。复合材料100℃裂解气体成分为氮气、二氯一氟乙烷、甲基膦酸二甲脂。4种泡沫在22～85℃的最大热膨胀量分别为–0.18%、–0.37%、–0.30%、–0.45%。环氧树脂与4种泡沫的粘黏强度在41～52N,而聚氨酯树脂达到了54～81N。结论 雷达吸波复合材料泡孔内残留气体的释放,是导致外观失效的根本原因。通过热处理工艺,减少样品残留气体量,并提升胶黏剂与泡沫的粘黏复合强度,是提升复合材料环境适应性的有效技术途径。     

Use of recycled plastics in wood plastic composites – A review

The use of recycled and waste thermoplastics has been recently considered for producing wood plastic composites (WPCs). They have great potential for WPCs manufacturing according to results of some limited researches. This paper presents a detailed review about some essential properties of waste and recycled plastics, important for WPCs production, and of research published on the effect of recycled plastics on the physical and mechanical properties of WPCs.     

Renewable Cellulose Derived Carbon Nanospheres as Nucleating Agents for Polylactide and Polypropylene

Nucleation of polylactide and polypropylene using novel renewable resource biobased carbon nanospheres (CNS) is investigated using differential scanning calorimetry and polarized optical microscopy. Isothermal studies near the optimal crystallization temperature demonstrate at least a five-fold increase in crystallization rate in PP but only a 1.4 times faster crystallization in PLA. Non-isothermal studies reveal an asymptotic relationship of the maximum crystallization temperature with increasing CNS weight loading in PP and no relationship in PLA. Microscopy indicates some aggregation in the solution blended samples and that average spherulite size is reduced 10-fold due to faster nucleation in the composites as compared to the neat polymer. The fractional crystallinity achieved during non-isothermal crystallization increases by about 7% with addition of a small amount of CNS and decreases with weight loading higher than 1%. The crystallization rates obtained in polypropylene are competitive with widely used mineral talc nucleating agents.     

基于ABAQUS的复合材料低速冲击损伤分析

目的分析不同冲击能量对复合材料层合板的损伤情况,验证有限元模型的合理性和有效性。方法以CCF300/10128H型碳纤维树脂基复合材料层合板为研究对象,采用落锤冲击试验机对层合板进行冲击实验,然后对冲击后的试验件进行超声C扫描。建立有限元模型,运用ABAQUS软件对冲击过程进行模拟。结果有限元模拟结果与实验结果吻合良好。结论复合材料层合板内部损伤随着冲击能量的增大而快速变大。出现穿透损伤以后,损伤趋于平缓,有限元模型能够较好地预测复合材料低速冲击损伤。     

g-C3N4/Bi2S3复合物的制备及可见光催化降解MO

采用简单溶剂热方法成功合成可见光催化剂g-C_3N_4/Bi_2S_3.合理地利用X射线衍射(XRD)、傅立叶红外光谱分析仪(FTIR)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM、HRTEM)、紫外可见漫反射光谱(UV-vis DRS)等表征手段对合成的样品进行了表征.与纯g-C_3N_4和Bi_2S_3相比,g-C_3N_4/Bi_2S_3复合物对甲基橙(MO)的可见光催化降解具有更高的降解效率.根据能带分析结果,电子-空穴对的有效分离增强了光催化效率.此外,提出了g-C_3N_4/Bi_2S_3对MO的光催化降解过程以阐明降解机制.提供了一种经济简单并易于规模化扩大开发可见光响应催化剂的方法,并在废水处理中具有潜在的应用价值.     

热/自然交变环境下玻璃纤维增强SiO2气凝胶复合材料模拟使役工况试验研究

目的 研究装备动力舱在热/自然交变环境下玻璃纤维增强SiO2气凝胶复合材料性能随模拟使役工况试验时间的退化规律,提升装备动力舱热/自然交变环境效应控制水平。方法 以玻璃纤维增强SiO2气凝胶复合材料为研究对象,以湿热、盐雾和高温试验为热/自然交变环境试验谱,以振动试验为加速因子,开展5个周期的实验室模拟使役工况加速试验,对比分析样件初始状态和每一个周期试验后的性能。结果 经模拟使役工况试验后,玻璃纤维增强SiO2气凝胶复合材料的颜色由白色逐渐变成黄色,SiO2气凝胶含量逐渐减少,纤维元素组成变化不明显,导热系数升高,隔热性能下降,且均在4周期模拟使役工况试验后出现明显变化。结论 玻璃纤维增强SiO2气凝胶复合材料经5个周期的模拟使役工况试验后,其常温导热系数仅为0.026 4 W/(m.K),热面温度为200 ℃时,冷面平均温度仅为68.5 ℃,热/自然交变温差为43.5 ℃,具有良好的环境适应性。     

生物硫铁生成菌的选育及其在重金属废水处理中的应用

为开发高效经济、环境友好的重金属废水处理技术,采用亨盖特(Hungate)厌氧技术分离出一株产生物硫铁复合材料的硫酸盐还原菌(Sulfate reducing bacteria,SRB),命名为SRB2,并对该菌株进行了生理特性、培养工艺和废水处理研究.菌体杆状稍有弯曲,革兰氏阴性菌,最佳碳源为乳酸钠.pH范围5.0～9.0,最适pH 7.0,最适温度为35℃,培养3 d生物硫铁量和硫化物含量能达最大值,分别为2.85 g L-1、358.048 mg L-1.正交试验结果表明,乳酸钠9.0 g L-1+组合氮源1.5 g L-1+硫酸亚铁10.0 g L-1时生物硫铁产量最高.16S rDNA序列分析表明,菌株与脱硫弧菌属Desulfovibriodesulfuricans strain 734同源性为99%.采用生物硫铁处理重金属Cu2+、Pb2+、Cd2+废水,结果表明生物硫铁能快速处理含Cu2+、Pb2+、Cd2+废水,2 min去除率达99.8%以上.因此,生物硫铁在各类重金属废水处理与重金属废水污染事故应急处理中具有较好的应用前景.     

玻璃纤维增强聚对苯二甲酸乙二醇酯/次磷酸铈复合材料的制备及其阻燃性能研究

首先合成并表征了一种新的阻燃剂-次磷酸铈（CHP）;然后采用熔融共混的方法制备了玻璃纤维（GF）增强聚对苯二甲酸乙二醇酯（PET）/CHP（PET/GF/CHP）复合材料;探讨了CHP对PET/GF复合材料热稳定性和燃烧性能的影响。材料的热稳定性是由热失重分析（TGA）进行表征的,燃烧性能是通过氧指数（LOI）、垂直燃烧（UL-94）以及锥形量热仪进行测试的,炭渣形貌由扫描电子显微镜（SEM）进行表征。结果表明：CHP的引入保持了PET/GF的热稳定性。含有15wt%CHP的PET/GF材料（PET/GF/CHP15）,其LOI为30%,且能达到UL-94V-0级别。此外,与PET/GF相比,PET/GF/CHP15热释放速率峰值和热释放总量分别下降了67%和27%。SEM分析表明CHP的加入使得材料在燃烧后有大量致密的炭渣覆盖在玻璃纤维的表面,这些炭渣不仅降低了玻璃纤维的导热性,而且切断了可燃物质的传送通道,从而提高了材料的阻燃性能。     

Bioabsorbable soy protein plastic composites: Effect of polyphosphate fillers on water absorption and mechanical properties

The use of synthetic and natural bioabsorbable plastics has been severely limited due to their low stiffness and strength properties as well as their strong tendency to absorb moisture. This research focused on the development of bioabsorbable polyphosphate filler/soy protein plastic composites with enhanced stiffness, strength, and water resistance. Bioabsorbable polyphosphate fillers, biodegradable soy protein isolate, plasticizer, and adhesion promoter were homogenized and compression-molded. Physical, mechanical, and water absorption testing was performed on the molded specimens. Results showed improvements in stiffness, strength, and water resistance with increasing polyphosphate filler content up to 20% by weight. Application of a coupling agent produced further mechanical property enhancements and a dramatic improvement in water resistance, interpreted by an interfacial chemical bonding model. Examination of the fracture surfaces of the materials revealed that the addition of the polyphosphate fillers changed the failure mode from brittle to pseudo-ductile. These results suggest that these materials are suitable for many load-bearing applications in both humid and dry environments where current soy protein plastics are not usable.     

环境友好新型聚乳酸复合材料的研究及应用

聚乳酸(PLA)复合材料是一类重要的环境友好新型可降解材料。该材料通常是以PLA高分子为基体,以无机钙质成分(如羟基磷灰石、磷酸钙、珊瑚、珍珠层)、碳纤维、生物活性成分、有机物等为增强材料复合而成。概述了近年来国内外通过共聚、共混、复合等改性方法获得PLA复合材料的研究进展;论述了PLA复合材料的制备方法、生物相容性、力学性能、开发现状及应用等;指出使用新型的复合工艺、采用超细的无机粒子或纳米增强材料或加入特殊填料,同时开发新型增强物质是PLA复合材料的发展趋势;展望了PLA复合材料的应用前景。