超临界水氧化技术处理有机废水的研究

超临界水是处理难氧化有机污染物的一种很好媒介,因为在超临界状态下有机污染物和氧化剂能够互溶而加快反应速度,具有去除率高,反应时间短且无污染等特点,因而受到了越来越多的关注。本文主要概述了超临界水氧化的特点、机理、工艺流程和存在的问题,介绍了当前超临界水氧化处理难降解污染物的效果、动力学、催化剂研究等情况,并展望了其应用前景。     

Unregulated emissions from diesel engine with particulate filter using Fe-based fuel borne catalyst

The alteration and formation of toxic compounds and potential changes in the toxicity of emissions when using after-treatment technologies have gained wide attention. Volatile organic compound（VOC）, carbonyl compound and particle-phase polycyclic aromatic hydrocarbon（PAH） emissions were tested at European Steady State Cycle（ESC） to study unregulated emissions from a diesel engine with a fuel-borne catalyst and diesel particulate filter（FBC–DPF）. An Fe-based fuel-borne catalyst was used for this study. According to the results, brake specific emissions of total VOCs without and with DPF were 4.7 and4.9 mg/kWh, respectively, showing a 4.3% increase. Benzene and n-undecane emissions increased and toluene emission decreased, while other individual VOC emissions basically had no change. When retrofitted with the FBC–DPF, total carbonyl compound emission decreased 15.7%, from 25.8 to 21.8 mg/kWh. The two highest carbonyls, formaldehyde and acetaldehyde, were reduced from 20.0 and 3.7 to 16.5 and 3.3 mg/kWh respectively. The specific reactivity（SR） with DPF was reduced from 6.68 to 6.64 mg/kWh. Total particle-phase PAH emissions decreased 66.4% with DPF compared to that without DPF. However, the Benzo[a]pyrene equivalent（BaPeq） with DPF had increased from 0.016 to 0.030 mg/kWh.Fluoranthene and Pyrene had the greatest decrease, 91.1% and 88.4% respectively. The increase of two- and three-ring PAHs with DPF indicates that the fuel-borne catalyst caused some gas-phase PAHs to adsorb on particles. The results of this study expand the knowledge of the effects of using a particulate filter and a Fe-based fuel-borne catalyst on diesel engine unregulated emissions.     

浅析废烟气脱硝催化剂环境管理

随着"十二五"期间国家对氮氧化物排放的控制越来越严格,选择性催化还原(SCR)烟气脱硝技术被广泛应用于火电厂的脱硝工程。本文介绍我国目前废烟气脱硝催化剂的产生情况、存在的环境风险以及发达国家的管理经验,从而提出我国将废烟气脱硝催化剂纳入危险废物管理,推行危险废物经营许可证制度,加强产生和经营单位的日常监督管理,从而促进行业的健康可持续发展。     

云母钛珠光颜料的应用研究

介绍了一种不使用有机溶剂获得云母钛珠光颜料、水性金属效果云母钛珠光浆、珠光涂料的环保型制备工艺和性能.采用液相沉积法获得了不同厚度的纳米TiO2薄膜包覆层而显示银白、金、红、紫、蓝、绿等各种色彩的系列珠光云母颜料;应用珠光云母颜料与分散剂等水性助剂混合,获得了水性金属效果云母钛珠光浆的制备工艺;应用云母钛珠光浆与乳液配合,获得了云母钛珠光涂料的制备工艺.制备的云母钛珠光涂料系列多彩,白度高、反射率大、珠光效果好,硬度、附着力、耐候性等指标优异.     

氮氟掺杂二氧化钛(N,F-TiO2)的制备及可见光催化活性的研究

以氨水为氮源,氢氟酸为氟源,采用溶胶-凝胶法制备了氮氟掺杂二氧化钛(N,F-TiO2)光催化剂,并通过X-射线衍射(XRD)和扫描电镜(SEM)技术对其晶型和形态进行表征.最后以酸性红B为模型污染物,探讨了N和F加入量、焙烧温度、焙烧时间、照射时间、催化剂用量、溶液初始浓度和照射功率等因素对N,F-TiO2可见光催化活性的影响.结果表明,制备的N,F-TiO2以锐钛型为主,N和F的掺杂对TiO2的晶相没有明显改变,但可以扩大TiO2的可见光响应范围.当N和F的加入量均为2.0%,且在500℃下焙烧40 min时,得到的N,F-TiO2的可见光催化活性明显高于单N或单F掺杂的TiO2(N-TiO2或F-TiO2).对于50 mL浓度为10.0 mg·L-1的酸性红B溶液,当催化剂加入量为1.5 g·L-1,128W光照3.0 h,溶液pH=5.6时,去除率为85.40%.适当延长光照时间至4.0 h,降解率几乎可达100%.另外,研究还证明了N,F-TiO2催化可见光降解过程中有.OH自由基生成.     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

锰铈脱硝催化剂的制备及其再生性能研究

采用等体积浸渍法制备了一系列Mn-Ce-Ox复合氧化物脱硝催化剂用于NH3选择性催化还原(NH3-SCR)NO。考察了Mn/Ce摩尔比、焙烧温度、H2O和SO2对Mn-Ce-Ox复合氧化物脱硝催化剂活性的影响及催化剂中毒再生性能。结果表明:当NH3:NO=1:1,空速为5 000 h-1,550℃焙烧制得的Mn/Ce摩尔比为5∶1的Mn-Ce-Ox复合脱硝催化剂活性最佳,活性温度窗口为100~260℃,在此温度区间内催化剂活性大于90%。200℃时,Mn-Ce-Ox复合催化剂活性最高为97.84%;在10%(V/V)H2O蒸汽和300×10-6SO2共存条件下,200℃时,催化剂活性在开始反应2.5 h内迅速下降至53%左右,并在之后的6 h内没有明显变化;中毒催化剂经常温水洗再生处理、质量分数为3%的硝酸溶液再生处理和550℃焙烧2 h再生处理后200℃活性均能恢复到90%以上,其中中毒催化剂经质量分数为3%硝酸处理后活性恢复率最高。     

Bi2O3-TiO2复合光催化剂协同处理铬-邻苯二甲酸酯复合污染

以硝酸铋和钛酸丁酯为前驱体,采用水热法制备了Bi_2O_3-TiO_2复合半导体材料,并利用X射线衍射(XRD)、紫外-可见吸收光谱(UVVis)、能谱分析(EDS)、X射线光电子能谱(XPS)等手段对复合材料的结构进行了表征.同时,考察了Bi_2O_3-TiO_2复合材料对重金属Cr(Ⅵ)和难降解邻苯二甲酸二丁酯(DBP)复合污染的处理性能,并探讨了复合催化剂协同处理复合污染的作用机制.结果表明:该复合催化剂在可见光下能同时降低重金属Cr(Ⅵ)和有机物DBP的浓度,抑制电子和空穴复合,表现出比对单一Cr(Ⅵ)及DBP污染物更高的处理效率.当Bi_2O_3含量为4%时,复合催化剂表现出最佳的光催化活性.     

Glucose production from hydrolysis of cellulose over a novel silica catalyst under hydrothermal conditions

A novel silica catalyst was synthesized by evaporation-induced self-assembly (EISA) method and tested for the catalytic selective hydrolysis of cellulose to glucose. This silica catalyst exhibited a higher catalytic activity than other oxides prepared by the same method, such as ZrO₂, TiO₂, and Al₂O₃. Using silica as a catalyst, cellulose was selectively hydrolyzed into glucose with a glucose yield as high as 50% under hydrothermal conditions without hydrogen gas. The silica catalyst was characterized by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results of temperature-programmed desorption of ammonia (NH₃-TPD) and textural properties indicated that the synergistic effect between strong acidity and a suitable pore diameter of the silica catalyst may be responsible for its high activity. In addition, the catalyst was recyclable and showed excellent stability during the recycle catalytic runs.