γ-Al_2O_3负载Ni、Fe催化剂同时脱硫脱硝

采用浸渍法制备了不同负载量的Ni(x)Fe(y)/γ-AL2O3催化剂,通过XRD、H2-TPR、BET和SEM对催化剂进行表征,使用微型催化反应装置考察催化剂在以CO作为还原气时,同时脱硫脱硝的催化活性。结果表明,Ni O和Fe2O3做为活性组分可以很好地分散在γ-Al2O3载体上,并且不破坏其结构;Ni(8)Fe(2)/γ-Al2O3催化剂有最佳的脱硫脱硝活性,脱硫率达到96.55%,脱硝率达到97.92%。     

异养硝化细菌Alcaligenes sp.S3除氮特性及动力学

从湘江生活污水排污口分离纯化的一株菌Alcaligenes sp.S3,在氨氮浓度为400 mg/L时,经过192 h的降解,氨氮的去除率达到88%,并且NH2OH和NO2--N并没出现积累。在对不同浓度的氨氮进行一级动力学拟合时发现,只有氨氮浓度较高时才很好地符合,浓度为500 mg/L时R2达到0.9923。酸性环境对Alcaligenes sp.S3生长有抑制作用,在pH7.5～10生长较好。摇床转速对Alcaligenes sp.S3除氮影响不大,C/N过低或过高对Alcaligenes sp.S3除氮都有影响。     

废水COD 4种物化表征方法的比较与评估

为了确定废水COD组分表征的物化分析方法,对0.1μm滤膜过滤、0.45μm滤膜过滤、絮凝和絮凝+0.45μm滤膜过滤4种方法进行了实验比较和评估。结果表明:某些材料的滤膜会因"COD溶出"而影响表征结果;4种方法分离废水的重现性都很好,相互没有明显区别;物化分离对废水快速可生物降解COD(SS)没有影响,但4种方法得到的处理液中可生物降解COD仍含降解速率明显不同的组分,其中SS仅占35%～45%。因此,物化方法不能合理表征SS;絮凝+0.45μm滤膜过滤速度快、干扰少、分离机理与活性污泥系统类似,更适用于废水溶解性惰性COD组分(SI)表征。     

阳(阴)离子复配修饰两性磁性膨润土的表面特征差异及对苯酚吸附的影响

以膨润土(BT)为基质,采用共沉淀法制备负载Fe3O4的磁性膨润土(MBT),在两性表面活性剂十二烷基二甲基甜菜碱(BS-12)修饰(BS-MBT)的基础上,以阳离子表面活性剂十六烷基三甲基溴化铵(CTMAB)/阴离子表面活性剂十二烷基磺酸钠(SDS)为复配修饰剂,通过湿法分别制备2种两性复配修饰磁性膨润土(BS-CT-MBT/BS-SDS-MBT),采用扫描电镜、X-射线衍射、热重、红外光谱对样品进行表征,测定磁性、比表面积和孔容等性质,通过批处理实验法对比两性复配修饰磁性膨润土对苯酚的吸附.结果表明,两性复配修饰膨润土具有良好的磁分离性能.与BS-MBT相比,BS-CT-MBT的C、N质量分数增大,复配修饰剂质量分数增加,孔容和比表面积减小,BS-SDS-MBT的C、N质量分数减小,复配修饰剂质量分数减少,孔容减小,比表面积增大.在pH 6.0的0.1 mol·L~(-1)Na Cl溶液中各修饰剂的解吸率低于9%.各土样对苯酚的等温吸附数据符合Henry模型,以分配吸附为主,吸附量顺序为BS-CT-MBTBS-MBTBS-SDS-MBTBTMBT,修饰剂质量分数是影响苯酚吸附的决定性因素,CTMAB提升土样吸附苯酚能力的效果高于SDS.     

Chemical characterization and source apportionment of PM1 and PM2.5 in Tianjin, China: Impacts of biomass burning and primary biogenic sources

The submicron particulate matter (PM₁) and fine particulate matter (PM_2.5) are very important due to their greater adverse impacts on the natural environment and human health. In this study, the daily PM₁ and PM_2.5 samples were collected during early summer 2018 at a sub-urban site in the urban-industrial port city of Tianjin, China. The collected samples were analyzed for the carbonaceous fractions, inorganic ions, elemental species, and specific marker sugar species. The chemical characterization of PM₁ and PM_2.5 was based on their concentrations, compositions, and characteristic ratios (PM₁/PM_2.5, AE/CE, NO₃^?/SO₄^2?, OC/EC, SOC/OC, OM/TCA, K+/EC, levoglucosan/K⁺, V/Cu, and V/Ni). The average concentrations of PM₁ and PM_2.5 were 32.4 µg/m³ and 53.3 µg/m³, and PM₁ constituted 63% of PM_2.5 on average. The source apportionment of PM₁ and PM_2.5 by positive matrix factorization (PMF) model indicated the main sources of secondary aerosols (25% and 34%), biomass burning (17% and 20%), traffic emission (20% and 14%), and coal combustion (17% and 14%). The biomass burning factor involved agricultural fertilization and waste incineration. The biomass burning and primary biogenic contributions were determined by specific marker sugar species. The anthropogenic sources (combustion, secondary particle formation, etc) contributed significantly to PM₁ and PM_2.5, and the natural sources were more evident in PM_2.5. This work significantly contributes to the chemical characterization and source apportionment of PM₁ and PM_2.5 in near-port cities influenced by the diverse sources.     

KMnO4-PAC对高原喀斯特湖库DOM的DBPsFP控制

以云贵高原典型喀斯特湖库红枫湖取水口溶解性有机质（DOM）为研究对象,调查不同组合方式下高锰酸钾-聚合氯化铝（KMnO₄-PAC）对消毒副产物的生成潜能（DBPsFP）变化和平均组成分布,并通过红外光谱（FTIR）和三维荧光光谱（3D-EEM）对部分样品进行化学表征,推断其影响机制.结果表明：在0.1,0.2,0.4mg/L KMnO₄投加量下,DBPsFP降低17.5~73%,DOM的卤代活性化学结构和官能团部分被有效钝化;PAC的网捕和卷扫效应使DBPsFP进一步减少27.9~86.1%,组合工艺对DBPs的生成潜能影响大小为：三卤甲烷（THM₄） > 卤乙酸（HAA₉） > 卤乙腈（HAN₄）/卤代酮（HK₂）/三氯硝基甲烷（TCNM）.FTIR的结果表明预氧化后3300cm^-1处的透过率降低,指纹区1000~1300cm^-1处的峰频提升,表明分子中的O-H、COOH和C-O官能团增加,共轭不饱和结构在KMnO₄作用下部分消失.3D-EEM验证了外源有机物（腐殖酸）在DOM中占比随KMnO₄浓度梯度升高而下降,同时类蛋白结构的吸收峰强度增加,说明最终DBPs贡献可能源于DOM中剩余的小分子类蛋白（氨基酸）.     

Chemical characterization and source apportionment of atmospheric submicron particles on the western coast of Taiwan Strait, China

Taiwan Strait is a special channel for subtropical East Asian Monsoon and its western coast is an important economic zone in China. In this study, a suburban site in the city of Xiamen on the western coast of Taiwan Strait was selected for fine aerosol study to improve the understanding of air pollution sources in this region. An Aerodyne high-resolution time-of-flight aerosol mass spectrometer(HR-To F-AMS) and an Aethalometer were deployed to measure fine aerosol composition with a time resolution of 5 min from May 1to 18, 2015. The average mass concentration of PM1 was 46.2 ± 26.3 μg/m~3 for the entire campaign. Organics(28.3%), sulfate(24.9%), and nitrate(20.6%) were the major components in the fine particles, followed by ammonium, black carbon(BC), and chloride. Evolution of nitrate concentration and size distribution indicated that local NOx emissions played a key role in high fine particle pollution in Xiamen. In addition, organic nitrate was found to account for 9.0%–13.8% of the total measured nitrate. Positive Matrix Factorization(PMF)conducted with high-resolution organic mass spectra dataset differentiated the organic aerosol into three components, including a hydrocarbon-like organic aerosol(HOA) and two oxygenated organic aerosols(SV-OOA and LV-OOA), which on average accounted for 27.6%,28.8%, and 43.6% of the total organic mass, respectively. The relationship between the mass concentration of submicron particle species and wind further confirmed that all major fine particle species were influenced by both strong local emissions in the southeastern area of Xiamen and regional transport through the Taiwan Strait.     

麦秸焚烧导致的北京市大气污染时空分布和化学组成特征分析

为了全面评价农田秸秆焚烧产生的污染事件,并为制定有效的管理措施提供依据,于2006年6月20日监测了西南风下北京南部农田麦秸焚烧产生的污染物向北京传输的过程.获得了SO2、CO、NOx以及可吸入颗粒物(PM10)质量浓度的数据.颗粒物的化学组分数据.数据分析结果表明,污染输送对北京市西南部地区空气质量影响最大(PM10小时浓度超过600μg·m-3),对北部山区影响较小(PM10浓度峰值在110μg·m-3).高浓度污染在市区持续时间最长.麦秸焚烧通过输送增加了PM10(尤其是PM1)、CO、NO2以及NMHC等污染物质,这使得与前一日相比污染物之间的相关关系发生了变化:SO2与其它污染物的相关性不显著,而CO与NO2、CH4与NO显著相关.因子分析进一步揭示,气象条件对污染物浓度变化具有主导作用,而由麦秸焚烧所产生的外来污染源属于次要地位.污染输送过程中,PM25中的硝酸盐类和有机碳、碳黑质量浓度增大.麦秸焚烧所输送的气态污染物和细小颗粒物对人体健康存在威胁,在不利扩散的气象条件下在大气中存留时间加长.研究结果表明,气象条件不利于污染扩散时必须禁止农田秸秆焚烧.     

具菲降解特性植物内生细菌的分离筛选及其生物学特性

从长期受石油污染的植物体内分离到内生细菌36株,通过平皿促生和定殖试验筛选出1株能高效降解菲并明显促进小麦生长、能在小麦体内良好定殖的内生细菌7J2菌株.同时,对菌株7J2的生物学特性进行了研究.结果表明,菌株7J2在菲含量为30 mg·L-1的条件下,28℃振荡培养6d,菲的降解率达到99.81%.菌株7J2能够产生吲哚乙酸(IAA)(3.4±0.2)mg·L-1)和铁载体(2,3-二羟基苯甲酸)(4.3±1.6) mg·L-1).振荡培养3d,接活菌的培养基中有效磷浓度比接灭活菌的处理增加了32.5%.另外,菌株7J2对重金属Pb2 、Cr2 、Cu2 、Ni2 、Zn2 、Cd2 均有较强的抗性.通过16SrDNA序列测定,菌株7J2属于肠杆菌属.     

苯基改性的介孔分子筛SBA-15的合成与表征

采用一步法在酸性条件下以聚乙氧基聚丙氧基聚乙氧基三嵌段共聚物(P123)为模板剂,用正硅酸乙酯(TEOS)和苯基三甲氧基硅烷(PTMS)直接缩合制备了苯基改性介孔分子筛Ph-SBA-15,并用红外光谱(FTIR)、小角X射线衍射(SAXRD)、热重分析(TGA)、透射电镜(TEM)和氮气吸附-脱附对样品进行了表征。结果表明,制备的样品不仅保持了高度有序的SBA-15的二维六角结构,而且具有较高的热稳定性,较大的比表面,孔容和孔径。