Ecological plasticity of nest-building behavior of the redwing (<Emphasis Type="Italic">Turdus iliacus</Emphasis> L.) in Karelia according to individual marking data

The placement of 1918 redwing nests has been analyzed, including 214 nests of 90 marked females (2–8 known nests per female). A high level of intraspecific and individual variation in utilization of different types of nest supports is described. It is shown that redwings choose nest sites without regard to previous experience (either positive or negative) or to the placement of their parent nest. Under conditions of the northern taiga, such behavior provides for significant reduction of chick mortality by the end of the season. This is con- firmed by comparison with the song thrush (T. philomelos), which nests mainly on spruce trees.     

酸性洗涤塔-生物滤塔-生物曝气池组合工艺处理恶臭气体NH3和H2S

采用酸性洗涤塔、生物滤塔和生物曝气池的组合工艺处理NH3、H2S恶臭混合气体,研究表明,该组合工艺对NH3和H2S有很好的去除效果,在进气流量为35 L/min,喷淋量45 L/h时,NH3进气浓度50.15~525.4 mg/m3,H2S进气浓度10.23~110.36 mg/m3时,NH3单一进气去除率稳定在99%以上,H2S单一进气去除率90%以上。混合进气后,NH3去除率几乎为100%,H2S的去除率提高至98%以上。在一定的浓度范围内,NH3和H2S之间的相互作用对两者的去除效果没有明显的影响,而且起到了相互促进降解的作用。同时,进气流量和填料层高度都会影响NH3、H2S的去除率。系统对进气容积负荷变化的缓冲能力强,在偶尔超负荷条件下运行并不能使系统崩溃,并且微生物对高负荷逐渐表现出适应性。大部分溶于水的氨由生物曝气池去除,去除率达到96.9%。     

On causes of gigantism in herbaceous plants

Landscape-geochemical features providing for manifestation of gigantism in herbaceous plants have been revealed in natural habitats in the south of Sakhalin and Kunashir islands. Tall herb assemblages have proved to be associated with geochemical landscapes characterized by reducing (gley or hydrogen sulfide) conditions and increased contents of petroleum hydrocarbons and some trace elements (total and movable forms). A hypothesis is put forward that gigantism in herbaceous plants is manifested in zones of active faults, which serve as a kind of conduits supplying endogenous heat, matter, and water to the root systems.     

生物法-人工湿地组合工艺处理小城镇混合污水研究

为适应小城镇污水处理高效、低耗、管理简单的要求,开展了生物法(水解酸化/生物接触氧化)-人工湿地组合工艺(A/BCO-CW)处理小城镇片区混合污水的研究。结果表明,A/BCO系统在停留时间为3～6 h条件下,对悬浮物和有机物有高的去除效率,COD、BOD5和TSS去除率分别达到63.1%、67.7%和66.2%,避免了人工湿地堵塞和提高处理效率,减少了所需湿地面积44%。全年运行结果表明,在0.30～0.59 m/d水力负荷率下,垂直流-表面流-水平潜流人工湿地组合系统对COD、BOD5和TSS平均去除负荷达9.4、5.1和7.2 g/(m2.d)(42%、71.2%和85.2%);COD、BOD5去除速率常数为74.6±12.1 m/y、166±30.5 m/y,这些数值均处于文献中k值范围的高量程内。A/BCO-人工湿地系统对COD、BOD5和TSS具有好的处理效果,出水水质能够稳定达到《地表水环境质量标准》(GB 3838-2002)的IV类水标准,2种处理方法有效组合起来,所开发的低成本、高效率、可持续运行的城镇废水处理组合系统,将会在实际应用尤其是高有机负荷污水处理中发挥良好效用。     

微波强化Fenton/活性炭工艺处理制药废水的影响因素

为了研究微波强化Fenton/活性炭工艺处理高浓度制药废水的影响因素,以阜新某集团公司生产制药原料排出的废水为研究对象,利用静态实验,采用混凝-微波强化Fenton/活性炭工艺对高浓度制药废水进行实验。实验用水为100 mL、COD为576~1 440 mg/L的制药废水,当活性炭投加量为2 g,H2O2投加量为3/4Qth,pH值为5,微波辐照功率和时间分别为500 W和7 min时,COD去除率可达到92.6%,出水COD在42.6~106.6 mg/L范围内。实验结果表明,活性炭的投加量、H2O2的投加量、pH值、微波辐照功率和辐照时间对微波强化Fenton/活性炭工艺的处理效果影响都较显著。     

污水低氧脱氮机制及其应用研究进展

阐述了污水低氧脱氮的基本原理,即抑制或去除亚硝酸盐氧化菌(NOB),同时保留氨氧化菌(AOB),并保持其活性;探讨了污水低氧脱氮实现途径;详细介绍了几种典型的污水低氧脱氮工艺(短程硝化(SHARON)工艺、厌氧氨氧化(ANAMMOX)工艺、好氧反氨化(DEMON)工艺、低氧自养硝化反硝化(OLAND)工艺、甲烷营养型硝化反硝化工艺和亚硝酸盐型完全自养脱氮(CANNON)工艺)的应用研究进展;最后对污水低氧脱氮处理工艺的工程运用进行了展望.     

壬基酚降解菌产酶条件的优化

通过单因素试验和正交试验确定了实验室保藏的壬基酚降解菌株沙雷氏菌(Serratiasp.LJ)的最佳产酶条件:以壬基酚、硫酸铵为碳源、氮源,培养基初始pH为6.8,培养温度为30℃,种子活化时间为24h,接种量为3%(体积分数)。在此条件下培养72h后,最高酶活力为1.314IU/mL,是优化前的1.77倍。     

Fenton氧化-序批式膜生物反应器耦合处理干法腈纶废水

采用Fenton氧化-序批式膜生物反应器(SBMBR)组合工艺处理干法腈纶废水。结果表明,在废水初始pH值为3.0,H2O2投加量为90.0 mmol/L,Fe2+投加量为20.0 mmol/L,反应时间为2.0 h的条件下,Fenton氧化预处理对腈纶生产废水的COD去除率达到47.0%以上,COD由1 091 mg/L降至560 mg/L,废水的BOD5/COD由0.32升至0.69,废水的可生化性得到显著提高。Fenton处理出水与丙烯腈废水等比例混合后,采用SBMBR进行生化处理,在水力停留时间为24 h,90 min缺氧/150 min好氧交替运行的条件下,COD、NH4+-N和TN的平均去除率分别为71.7%、97.2%和47.4%,碳源不足是限制TN去除效果的主要影响因素。在无外加碳源的条件下,组合工艺处理后出水COD和NH4+-N浓度分别为117 mg/L和1.7 mg/L,出水水质可以稳定达到国家一级排放标准(GB8978-1996)。     

Choice of parameters for passive shielding of power-frequency magnetic fields

Epidemiological studies suggesting the possibility of harmful effects on human (specifically children’s leukaemia) due to long-term exposure to magnetic fields of extremely low frequency (e.g. 50/60 Hz) and relatively low values (i.e. over the microtesla range) have stirred high activity in the topic of magnetic field mitigation. To reduce these fields, it is common to use passive metal screens (e.g. plates made of aluminium or steel). To design them, effective and fast numerical computations are highly desirable. In this article, a method is presented, which computes various parameters of screens in a given shielding problem and yields magnetic field distribution and shielding factors. The method takes into consideration the 3D field distribution and is able to solve systems with large aspect ratios (thin thickness in comparison with its other dimensions); this is a common problem where other methods such as finite elements often experience difficulties. The presented method computes separately the field inside and outside the screens. Afterwards, the solutions are “stitched” together along the border of the subregions. Two practical examples are given of the developed numerical method.