石灰调质污泥的燃烧特性及动力学分析

采用热重-差示扫描量热同步分析仪,在空气气氛下对石灰调制污泥进行燃烧失重实验.通过分析获得的曲线,可以将调质污泥的热反应过程分为4个阶段:自由水和化学结合水析出阶段;易挥发有机质析出和燃烧阶段;难挥发有机质析出分解和燃烧阶段;无机质的分解阶段.添加石灰后,污泥的着火温度小幅上升,综合燃烧特性指数随添加量增加而减小.采用Coats-Redfern积分法对挥发分析出和燃烧阶段进行了热反应动力学求解,发现添加量小于30％时,石灰可以减少污泥燃烧的活化能,促进污泥挥发分的析出和燃烧.     

我国废炼油催化剂的产生量、危害及处理方法

根据我国每年的石油消费量估算了当年的废炼油催化剂产生量,预测2015年我国废炼油催化剂的产生量将达到2.07×105 t。介绍了废炼油催化剂的主要成分、含量与危害,分别论述了废流化催化裂化催化剂、废催化加氢催化剂和废催化重整催化剂的处理和利用方法,指出废炼油催化剂的再生及资源化和无害化应是未来的重点研究方向。     

Fe_2O_3和K_2CO_3对钙基添加剂脱硫脱硝的影响

在研究焦炭燃烧过程中使用钙基添加剂固硫的基础上,探讨了Fe_2O_3或K_2CO_3对CaO脱硫脱硝的影响。实验结果表明:添加剂的种类对焦炭燃烧过程中排放的SO_2和NO的浓度及总量均有一定的影响;加入Fe_2O_3或K_2CO_3替代部分CaO后,焦炭燃烧过程中排放的SO_2和NO比单独加入CaO时均有所下降;向焦炭中分别混合3.0%(w)CaO),1.5%(w)CaO+1.5%(w)Fe_2O_3,1.5%(w)CaO+1.5%(w)K_2CO_3的添加剂时,焦炭的SO_2排放总量分别降低了69.93%,75.98%,79.98%,NO排放总量分别降低了64.38%,79.73%,84.14%;加入Fe_2O_3或K_2CO_3后,钙基添加剂的表面性质发生了变化,同时增加了反应的活性中心数,因而复合添加剂能更有效地进行脱硫脱硝。     

磁性活性炭催化臭氧氧化降解水中甲基橙

通过浸渍法制备了钕铁硼磁性活性炭(Nd Fe B/AC),采用SEM和VSM技术对其进行了表征,并将其作为非均相催化剂用于臭氧氧化降解水中甲基橙(MO)。表征结果显示:Nd Fe B/AC具有硬磁特性;当m(Nd Fe B)∶m(AC)=1∶2时,其比饱和磁化强度和比剩余磁化强度分别为15.9 A·m2/kg和6.0 A·m2/kg,矫顽力可达104.5k A/m。实验结果表明:在Nd Fe B/AC投加量为3.0 g/L、初始溶液p H为5.0、初始MO质量浓度为20 mg/L、臭氧质量浓度为15.0 mg/L、室温的条件下反应40 min,MO降解率达93.9%,显著优于投加AC的64.4%;AC和Nd Fe B/AC催化臭氧氧化降解MO的反应过程均遵循一级动力学规律,且Nd Fe B/AC的反应速率常数为AC的近3倍。     

Studies on the use of low-volatile non-edible oils in a thermal barrier-coated diesel engine

Owing to the ever-increasing vehicle population, the consumption of diesel fuel in the transportation, agricultural and industrial sectors has increased at an alarming rate. This has led to rapid fossil fuel depletion, ozone depletion and environmental degradation, which have become a serious concern. Search for alternative renewable and clean energy fuel sources to mitigate the emissions of greenhouse gases is continuing, and attempts to find different techniques for efficient utilization of these fuels are also undertaken. Biodiesel being an oxygenated fuel obtained from vegetable oils has received greater attention over the years as a promising alternative to diesel fuel. However, vegetable oils exhibit high viscosity, poor volatility and poor cold-flow characteristics. These characteristics can cause the following problems in the engine when run for a longer duration: injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication. These problems can be eliminated or minimized by adopting suitable fuel processing techniques to obtain biodiesels from vegetable oils. The fuel processing techniques vary widely, which include transesterification, supercritical methanolysis, ultrasonic and continuous microwave-assisted transesterification methods. In the present study, the transesterification method is effectively used to obtain biodiesels from non-edible oils of honne and cotton seed. The biodiesels obtained from these oils were used in the unmodified diesel engine to check their feasibility as diesel engine alternatives. Different thermal barrier coatings (TBCs) were applied on the piston, cylinder head, and inlet and exhaust valve surfaces of the diesel engine in order to make it a fully adiabatic engine. The engine with such TBCs is called a low heat rejection engine. For the present study, the TBC of partially stabilized zirconia (PSZ) and aluminium oxide (Al₂O₃) were selected. Finally, the performance of the diesel engine fuelled with different biodiesels in both conventional and thermal barrier-coated modes was compared. The thermal barrier-coated engine with the PSZ version showed better performance with increased nitric oxide emissions when compared with the Al₂O₃ coating.     

1000 MW机组SCR脱硝系统运行中的问题及措施

针对某电厂1000 MW机组SCR脱硝系统运行中出现的突出问题,分析原因并提出治理措施,经实践检验,通过优化燃烧调整、对氨喷射系统及导流板进行优化、更换液氨蒸发器、脱硝催化剂层增加声波吹灰器、空预器进行相应技改后,效果明显,脱硝系统及下游设备空预器运行正常,为同类机组脱硝系统的技改和运行提供了参考。     

适用循环流化床锅炉的脱硝技术

循环流化床锅炉由于NOx 排放浓度低在我国应用十分广泛,但如果不采取任何环保措施已不能满足目前的环保要求。简要分析了NOx的产生机理,通过几种脱硝技术的对比,指出循环流化床采用低氮燃烧＋SNCR脱硝技术是较好的选择。     

WSH-2型催化剂在环氧丙烷/苯乙烯装置废气处理中的工业应用

介绍了WSH-2型催化剂在环氧丙烷（PO）/苯乙烯（SM）装置废气处理中的应用。工业化装置的运行结果表明,在废气处理量86 000 Nm³/h、设定反应器进口温度250~300 ℃、设定进口非甲烷总烃（NMHC）质量浓度1 000~2 200 mg/m³的条件下,无论单系列还是双系列运转,采用WSH-2型催化剂均可对废气进行有效处理。处理后气体中的NMHC、苯、甲苯、乙醛、SM等的含量均符合GB 16297—1996《大气污染物综合排放标准》和GB 14554—1993《恶臭污染物排放标准》中的相关规定。NMHC去除率达到92.9%以上,装置运行稳定。按照目前的废气排放工况推算,预计催化剂的使用寿命可达5 a。     

碱熔融活化固硫灰制备地聚合物

采用碱熔融活化法,由固硫灰制备地聚合物。在前期开展的单因素实验的基础上,采用正交实验,考察了NaOH和固硫灰的质量比、煅烧温度、煅烧时间3个因素对固硫灰基地聚合物的抗压强度的影响。采用XRD,SEM,IR等手段分析固硫灰碱熔融活化前后的物相、微观形貌以及硅铝化学键的变化。实验结果表明,以在NaOH与固硫灰的质量比为0.60、煅烧温度为550 ℃、煅烧时间为60 min的条件下制备的碱熔融固硫灰为原料,制备的固硫灰基地聚合物的抗压强度为38.00 MPa。表征结果显示：通过碱熔融活化固硫灰制备的地聚合物的XRD谱图中出现了地聚合物的特征衍射峰;碱熔融固硫灰的结构松散,在颗粒表面及内部存在大量孔隙;经碱熔融处理后固硫灰的硅酸盐和铝酸盐发生了解聚。     

TiO2光催化法降解空气中的苯

以紫外灯为光源,采用P25型TiO₂光催化降解空气中的苯。为保证TiO₂的高分散性、增加其在铝板上的附着牢固性,加入了聚乙烯醇和硅溶胶,这在一定程度上增加了催化剂对光能的利用率,但也造成了催化剂活性的降低。实验结果表明：苯的光催化降解反应属一级动力学反应;苯降解率随初始苯质量浓度的增加而减小,随反应面积的增大而增大,在253.7 nm波长光源下的降解效果优于365.0 nm;苯降解所得的气相产物主要为CO₂和CO;随使用次数的增加,催化剂失活现象逐步显现;双氧水对催化剂的再生效果优于去离子水。