二段生物接触氧化工艺在中水回用中的特性研究

以规模小区生活污水为水源，对采用聚丙烯网状填料和强化炉渣组合填料的二段生物接触氧化工艺（以下简称二段法）进行了试验研究，试验针对本工艺的各项技术指标、影响因素以及各相关参数进行了较系统的试验测试。结果表明，反应器在第一接触氧池HRT为20 min、气水比为6∶1和第二接触氧池HRT为25 min、气水比为5∶1条件下，接触氧化池达到最佳降碳条件；反应器在第一接触沉池上升流速5.5 m/h和第二接触沉池上升流速4.5 m/h条件下，接触沉淀池达到最佳处理条件。     

Facilitating substance phase‐out through material information systems and improving environmental impacts in the recycling stage of a product

The amount of electrical and electronic products is increasing rapidly, and this inevitably leads to the generation of large quantities of waste from these goods. Some of the generated e‐waste ends up in regions with sub‐standard recycling systems and may be processed under poor conditions. During uncontrolled incineration, halogenated dioxins and furans can be generated from brominated and chlorinated compounds in the products. In order to reduce the health and environmental risks involved in the recycling stage of the life cycle of electronics, an effective design‐for‐environment process must be established during the product development phase. Knowledge of the chemical substances in the product is crucial to being able to make informed decisions. Through full knowledge of the material content of procured components, phase‐outs of unwanted substances, such as halogenated substances, can be performed in an effective manner. Therefore, information is the key to success in phasing‐out substances; facilitating compliance of legal provisions for manufacturers of electrical and electronic devices; and improving the environmental footprint of products as they reach the end of the life cycle. After an introduction to the challenges of electronics waste management, this paper describes supply chain information systems and how they are used to facilitate substance phase‐outs in the electronics industry. Sony Ericsson has been working with phase‐outs of unwanted substances since it was founded in 2001. Through the introduction of a material declaration system that keeps track of all substances in the components used in the company's products, Sony Ericsson has been able to replace unwanted substances to improve environmental impacts at the recycling stage of a product.     

废LCD面板有机材料水热资源化产乙酸

LCD面板主要由附着偏光片及液晶等有机材料的玻璃面板构成。有机材料的去除及资源化利用是废LCD面板处理的第一步。在水热条件下对废LCD面板进行了降解产酸研究。研究考察了反应温度、反应时间、氧化剂用量、水用量及pH值等对水热产乙酸产率及选择性的影响。通过正交实验确定了水热产乙酸的最佳操作条件：反应温度325℃，反应时间5min，氧化剂（30％H2O2）0．6mL，用水量2mL，近中性环境（pH6-6．5去离子水）。此条件下，乙酸产率及选择性分别为68．83％及70．56％。结果表明，以废LCD面板有机材料为原料，采用水热技术进行产乙酸反应，可实现其资源化再利用。     

地下水PRB原位生物修复中一种释氧材料的改进技术及效果分析

释氧材料经济有效的释氧是地下水原位生物修复的关键因素。实验通过在释氧材料中加入膨润土、磷酸二氢钾和硫酸铵等,改进释氧材料的性能。柱实验结果显示,该释氧材料释氧速率缓慢,释氧时间长,可以使溶液中DO长期保持在5 mg/L以上;另外,释氧材料中添加的缓冲剂及天然含水层介质对pH值有较好的缓冲作用,可以使pH值达到后续生物修复的要求。     

酸雨对建筑材料的影响及防治研究综述

综合分析了酸雨对建筑外墙的涂料、石材、混凝土等主要建筑构件的腐蚀原理，并提出了防治措施，来预防酸雨对建筑材料的侵害。     

Energy efficacy used to score organic refuse pretreatment processes for hydrogen anaerobic production

The production of hydrogen through Anaerobic Digestion (AD) has been investigated to verify the efficacy of several pretreatment processes. Three types of waste with different carbon structures have been tested to obtain an extensive representation of the behavior of the materials present in Organic Waste (OW). The following types of waste were selected: Sweet Product Residue (SPR), i.e., confectionary residue removed from the market after the expiration date, Organic Waste Market (OWM) refuse from a local fruit and vegetable market, and Coffee Seed Skin (CSS) waste from a coffee production plant. Several pretreatment processes have been applied, including physical, chemical, thermal, and ultrasonic processes and a combination of these processes. Two methods have been used for the SPR to remove the packaging, manual (SPR) and mechanical (SPRex). A pilot plant that is able to extrude the refuse to 200 atm was utilized. Two parameters have been used to score the different pretreatment processes: efficiency (ξ), which takes into account the amount of energy produced in the form of hydrogen compared with the available energy embedded in the refuse, and efficacy (η), which compares the efficiency obtained using the pretreated refuse with that obtained using the untreated refuse. The best result obtained for the SPR was the basic pretreatment, with η = 6.4, whereas the thermal basic pretreatment gave the highest value, η = 17.0 for SPRex. The best result for the OWM was obtained through a combination of basic/thermal pretreatments with η = 9.9; lastly, the CSS residue with ultrasonic pretreatment produced the highest quantity of hydrogen, η = 5.2.     

燃煤电厂袋式除尘器滤料耐氧化性能试验研究

燃煤电厂锅炉烟气中含有SOx和NOx,会氧化腐蚀滤料。试验研究了燃煤电厂布袋除尘器滤料断裂强力与运行时间的关系。结果表明,滤料在酸性环境中会被氧化同时断裂强力下降,但断裂强力下降后均会出现反弹,后处理工艺可提高滤料的抗氧化性能,但会降低滤料的断裂强力。     

环境生物样品预处理中的微波溶样技术

微波溶样是近年产生的一种崭新的有前途的样品预处理技术，本文评述这一技术在环境、生物样品消解方面的近期应用。     

长年关水稻田耕作改制的选择

试验研究表明,当早稻收获时间作晚稻才开始幼穗分化,即适宜早、晚稻出穗开花之间有60多天的时间,种植双杂间作稻就可获得好的收成,效果、效益都很显著。1992年用D 优287间汕优63,在达县永进乡的示范田中个别田块产量已达15t/ha,而盆地丘陵区适宜早、晚稻出穗开花之间的时间多数地区不到70天,种植双杂连作稻有困难。且双杂间作稻在抗灾增产,合理利用农村劳动力,提高稻田复种等方面优于双杂连作稻。因此,四川盆地丘陵区的中稻→冬水田在耕作改制中发展部分双杂间作稻是恰当的,其范围在巴中、盐亭、简阳一线以南海拔400m 以下的广大丘陵区。     

粉料无尘装车机工作原理及其在冶金厂矿的应用

介绍集装车与防尘统一于一体的无尘装车技术及具有设备本质安全化特点的无尘装车机在解决粉状物料装车作业时的扬尘问题,保护作业工人健康,维护厂区环境方面的重要优越性。