加氯消毒过程中纯细菌物质生成消毒副产物研究

按照UFC方法对水体中3种常见细菌Acinetobacter junii、Staphylococcussciuri和Escherichia coli进行纯细菌加氯消毒处理,同时考察水中溴离子对纯细菌物质生成DBPs的影响.结果表明,3种细菌均为DBPs前体物,加氯消毒生成的DBPs除水合三氯乙醛(CHD)外,生成的三卤甲烷(THMs)物质主要为氯仿(TCM),卤乙腈(HANs)物质主要为二氯乙腈(DCAN).氯仿的生成量与细菌物质TOC浓度无明显关系,但HANs和CHD生成量均随细菌TOC浓度增大而增加.其中革兰氏阳性细菌Staphylococcus sciuri生成的DCAN和CHD比革兰氏阴性细菌Acinetobacter junii和Escherichia coli生成的要高,说明细胞壁的化学组分可能是DCAN和CHD生成的影响因素之一.Escherichia coli细菌反应液中溴离子(Br-)存在时,除生成CHD、TCM及DCAN外,THMs和HANs中的溴代种类CHBr3随Br-增多而持续增加,相反TCM持续减少.当Br-浓度为4mg.L-1时,TBM浓度增至最高127.9μg.L-1;HANs和CHD生成量随Br-浓度增加先有所增加,随后持续降低至低于检测限;Br离子存在时THMs为主要DBPs种类.     

沈阳市地铁疏干水的利用探析

针对沈阳市地铁疏干水利用的现状,综合考虑沈阳市的实际情况,总结出地铁疏干水利用的几种方法,主要包括作为运河、湖泊的补换水源,用于修复、重建湿地,农业灌溉用水以及作为水源热泵的水源等。提出沈阳市地铁疏干水利用的指导思想和法律保障。     

黑箱加速大气暴露试验热强化效应和相关性研究

利用温湿度测量仪监测黑箱内的温湿度变化,分析黑箱自然加速试验装置的热强化效应。以3种不同配方的丙烯酸涂料为试验对象,在江津地区高温高湿环境下开展了黑箱加速大气暴露试验和朝南45°角大气暴露试验,从模拟性和加速性2个方面研究了2种试验方法的相关性。分析结果表明,黑箱加速大气暴露试验方法与朝南45°角大气暴露试验方法之间的相关性相当高。     

野战弹药储存防热现状及温度指标论证

分析了野战弹药的储存防热现状,论证了野战弹药储存防热的温度指标。通过对火炸药储存性能参数的计算并结合我国的实际气候状况,确定了野战弹药的储存防热指标为环境温度应控制在40℃以下。最后,提出了今后野战弹药储存防热的研究方向。     

活性炭孔结构和表面化学性质对吸附硝基苯的影响

通过对活性炭HNO3氧化及随后的N2:气氛中热处理,研究了活性炭性质对其吸附硝基苯性能的影响.以低温液氮(N2/77K)吸附测定活性炭的比表面积和孔容、孔径分布,以SEM观测活性炭表面形貌,以Boehm滴定、FTIR、零电荷点pHpzc测定及元素分析定量表征活性炭表面含氧官能团变化.结果表明, HNO3氧化可以显著改变活性炭表面化学性质,增加活性炭表面酸性含氧官能团数量,对活性炭孔隙结构影响不大.随后N2:气氛中热处理可以造成活性炭表面酸性含氧官能团分解,外表面积增大,微孔烧蚀为中孔.硝基苯在活性炭上的吸附基本符合Langmuir方程,改性后活性炭对硝基苯的吸附容量明显改变, ACNO-T、ACraw、ACNO吸附容量分别为1011.31、483.09、321.54 mg·g-1.较大的外表面积、适宜数量的中孔以及较少的酸性含氧官能团是ACNO-T对硝基苯表现出较高吸附容量的主要原因.     

Experimental investigation of open core downdraft biomass gasifier for food processing industry

This paper deals with field related experience of a low temperature industrial heat application through biomass gasification. The gasification system is essentially consists of an open top down draft reactor lined with ceramic. The experiment reveals that 6.5 kg of liquefy petroleum gas (LPG) is fully replaced by 38 kg of sized wood on hourly basis. The maximum temperature attained was 367°C in 130 min at 100.7 Nm³ h⁻¹ gas flow rate. This system has resulted a saving of about 19.5 tons of LPG over 3,000 h of operation, implying a saving of about 33 tons of CO₂ emission, thus a promising candidate for clean development mechanism. Fuel economic analysis of gasifier system showed that the saving was about 13,850 US$ for 3,000 h of baking operation.     

Waste‐to‐energy recovery potential: A case study at Jaipur railway station

A study was conducted at the Jaipur railway station in Jaipur, India, to give the perspectives of the actual waste management practices there. Required information was collected from the stakeholders by means of semi‐structured questionnaires, individual and group interviews, and recorded, official data regarding waste generation, collection, transportation, and disposal. Further quantitative and compositional analyses were performed by means of surveys and measurements. Field visits were made for collection of waste samples for quantification and for the study of its management. The field data were compiled and analyzed by sorting the waste into different components. It was found that 1.8 tons of solid waste is collected per day, and a considerable percentage of it comprises paper, plastic, and glass. Excluding the inerts, which are irrelevant from the point of view of energy saving and recovery potential, the average moisture content was found to be 3.38%. From the perspective of life cycle analysis, the option of composting or recycling would give savings of 28.33 gigajoules (GJ) per day over landfilling, while combustion would give savings of 2.97 GJ per day in comparison to landfilling. Analysis based on a compositional model gives a heat value of 8,157.87 kilojoules per kilogram, which amounts to 14.68 GJ of energy per day.     

双向微槽道多孔复合结构沸腾传热研究

目的研究出新型的表面结构,以提高沸腾传热强化。方法在紫铜板上烧结铜粉多孔层,然后利用线切割对多孔层进行开槽。研究槽道参数包括槽数、槽宽、槽间距和槽向等对沸腾传热效果的影响。结果开槽增大了传热的表面积,有利于气体逸出,减少气体的逸出阻力,从而多孔表面开槽强化了沸腾传热效果,传热系数与光滑表面相比可提高2~3倍。与单向微槽道相比,双向交叉槽道有着更好的传热效果,能够形成一个稳定的液体补充和气体逸出网络。结论在多孔表面加工微型复合结构,能够大幅度提高沸腾传热强化。     

环境实验箱气流组织与围护结构耦合传热研究

目的研究环境实验箱在升、降温过程中气流组织与围护结构的耦合传热行为,为环境实验箱制冷/加热能力的确定提供精确的设计方法。方法首先利用UC240环境实验箱搭建实验平台,测量环境箱送风口速度分布,以及升、降温过程中室内及壁面的温度曲线,然后对环境箱进行建模,以实测的送风速度、温度作为边界条件,利用CFD方法进行仿真,最后对比分析实验值与CFD仿真的结果。结果利用CFD方法计算得到的环境箱升、降温曲线与实测值吻合较好,尤其是壁面温度曲线,误差不超过4℃。送风温度可以根据蒸发器理论或加热功率和回风温度而动态地确定。结论利用CFD方法分析环境实验箱气流组织与围护结构的耦合传热是可行的,FLUENT的UDF功能可根据需要扩展,以协助设计蒸发器和控制策略。     

方舱传热试验方法研究

阐述了方舱传热系数的意义,介绍了美国材料与试验学会标准ASTM E 1925《刚性壁再配置结构的工程和设计标准规范》和GJB 2093《军用方舱通用试验方法》中方舱传热试验方法,从传热学理论和实际试验2方面对方舱传热试验进行了研究.结果表明,按照GJB 2093中热电偶的布置要求,在舱内整个立体空间内并不能真正达到温度...