Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

不同浓度锌处理下水稻幼苗对镉的累积效应

为探究锌（Zn）对水稻镉（Cd）累积的影响及其根表铁膜所发挥的作用,选取Cd高累积型水稻品种中9优547（简称"Z547"）和Cd低累积型水稻品种金优402（简称"J402"）,采用温室水培试验,研究0、2、5、10、15和20 μmol/L等6个Zn浓度下水稻幼苗对Cd的累积效应,以及不同浓度Zn处理对根表铁膜生成量的影响.结果表明:①随着c（Zn）的增加,Z547和J402水稻幼苗生物量均呈先增后减的趋势,分别在c（Zn）为2和10 μmol/L时达到最大值.②Z547和J402水稻幼苗中w（Cd）均呈先降后增的趋势,分别在c（Zn）为5和2 μmol/L时达到最小值;当水稻幼苗中w（Cd）达到最小值时,Z547根和地上部中w（Cd）分别为31.65和11.47 mg/kg,J402根和地上部中w（Cd）分别为22.58和14.36 mg/kg.③不同浓度Zn处理下水稻幼苗各部位中w（Cd）均与根表铁膜中w（Mn）、w（Fe）、w（Fe+Mn）呈显著正相关,高铁膜处理水稻幼苗中w（Cd）显著高于低铁膜处理,表明根表铁膜生成量的增加会促进Cd在水稻幼苗中的累积.研究显示,当c（Zn）较低时,c（Zn）的增加会抑制水稻幼苗对Cd的累积;当c（Zn）较高时,c（Zn）的增加会促进水稻幼苗对Cd的累积,而Zn可通过控制根表铁膜的生成来影响水稻幼苗对Cd的累积.      

2019年10~12月京津冀及周边“2+26”城市重污染减排效果评估

为评估京津冀及周边区域重污染过程期间应急减排措施的效果,基于情景模拟的方法,采用NAQPMS模式和多种观测资料,分析了2019年10~12月期间京津冀及周边区域环境空气质量、重污染过程和气象条件概况,评估了模式24、72和144 h的PM_2.5预报效果,并对应急减排措施的效果和不确定性进行了讨论.结果表明,2019年10~12月京津冀及周边"2+26"城市PM_2.5平均浓度64 μg ·m^-3,同比降低了10 μg ·m^-3;区域性重污染过程4次,受影响城市重污染过程期间PM_2.5平均浓度156 μg ·m^-3."2+26"城市PM_2.5气象条件评估指数（EMI）变化值范围为-15.6%~16.8%,EMI显示北京、天津和石家庄等12个城市气象条件与同期相比变差,变差程度范围为3.2%~16.8%.减排情景模拟分析显示应急减排措施有效减少了区域性重污染过程的发生,污染物峰值浓度降幅明显,未出现区域性严重污染过程.典型重污染期间,北京、石家庄、保定和唐山等城市PM_2.5日均浓度削减2%~9%.区域应急减排措施促使"2+26"城市PM_2.5季度均值分别降低1~3 μg ·m^-3左右,区域性减排效果明显.     

德州市夏季臭氧敏感性特征及减排方案

近年来德州市臭氧污染频发,2018年夏季（6~8月）,德州市发生了严重臭氧污染事件,臭氧日最大8 h浓度值超标天数达60 d,超标率65%,3个月平均值为176 μg ·m^-3,最高达262 μg ·m^-3.本研究利用WRF-CAMx耦合的HDDM模块,分析期间德州臭氧敏感性特征及减排方案.结果表明,在空间上,德州市中心城区为VOCs控制区,而郊区为NO_x与VOCs协同控制区.在时间上,VOCs敏感值每日为正值,但dO₃_V₅₀在6月（城区18.7 μg ·m^-3,郊区19.7 μg ·m^-3）和8月（城区15.3 μg ·m^-3,郊区16.4 μg ·m^-3）高于7月（城区13.0 μg ·m^-3,郊区11.8 μg ·m^-3）,NO_x敏感值城区呈正负交错,郊区大部分为正值,并与VOCs敏感值接近.对于城区减排方案应考虑以仅VOCs削减为优先,而郊区由于NO_x和VOCs对臭氧减排效果相当,建议以NO_x：VOCs=1：1为优.     

CeO2形貌结构对催化湿式空气氧化苯酚性能的影响

采用水热法、沉淀法和溶胶凝胶法制备了3种不同形貌的CeO₂催化材料,并将其用于湿式空气氧化苯酚水溶液过程中,探讨了CeO₂形貌结构对催化湿式氧化苯酚水溶液性能的影响.采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）、程序升温还原（TPR）等手段对CeO₂催化材料进行了表征.结果表明,水热法制备的CeO₂催化材料表现出较好催化性能,主要原因是水热法合成的CeO₂呈现交错的纳米棒状结构,主要暴露（220）晶面,且沿着（220）晶向生长.在反应温度为200℃、空气压力为2MPa、苯酚初始浓度500mg/L的条件下,最终（240min）COD的去除率为95.5%.     

氮掺杂二氧化钛负载钒磷氧催化氧化NO的实验研究

以VPO为活性组分,N掺杂TiO 2为载体,采用浸渍法制备了VPO/TiN催化剂,基于单因素实验研究了其对NO的选择性催化氧化(SCO)性能以及抗硫抗水性能。研究表明:当P/V为1/5、N/Ti为1、活性组分负载量为10%、焙烧温度为350℃时,催化剂的SCO活性最好,NO氧化率达到61%;光致发光光谱(PL)表征显示N掺杂TiO 2在催化剂表面形成的氧空位可增强催化剂对O 2的吸附;VPO/TiN催化剂抗硫抗水性能较强,反应后的催化剂表面未发现硫酸根的特征峰,水蒸气主要通过与NO竞争吸附占据活性位点来抑制催化剂的SCO活性。     

土壤胡敏素对铜离子的吸附作用及其机理研究

以暗棕壤为供试土壤,研究了不同溶液pH值、离子强度、接触时间、反应温度和初始铜离子(Cu~(2+))浓度条件下,胡敏素对Cu~(2+)的吸附作用;利用扫描电子显微镜(SEM)、X-射线能量色散谱(EDS)、傅立叶变换红外光谱(FTIR)和X-射线光电子能谱(XPS),对胡敏素/胡敏素-Cu~(2+)复合物的表面形貌、元素分布和官能团组成进行了分析;应用延展X-射线吸收精细结构谱(EXAFS),对吸附态Cu~(2+)的局域配位结构进行了表征.结果表明:胡敏素对Cu~(2+)的吸附量随pH值、接触时间、反应温度和Cu~(2+)浓度的增加而增加,但随离子强度的增加而下降;吸附动力学符合准二级动力学方程,而吸附等温线用Langmuir方程的拟合效果较好;吸附过程需要能量,是自发、吸热和自由度增加的缔合反应;吸附Cu~(2+)之后,胡敏素表面产生了团聚现象,表面羧基、羟基、吡啶氮和N—O基团参与了Cu~(2+)的吸附作用,同时吸附态Cu~(2+)是以内层配位形式与胡敏素表面的O/N和C原子结合.     

MgO低温催化臭氧降解氨氮的机制研究

研究了低温条件下单独臭氧及MgO催化臭氧化降解水中氨氮的效率和特征,并对其反应机制分别进行了探讨.结果表明,pH是影响臭氧和催化臭氧化除氨的重要因素,不仅影响溶液中NH_3与NH~+_4的比例和臭氧氧化氨氮的速率,还影响氧化产物种类,从而影响脱氮效果.10℃时,单独臭氧对水中氨氮的氧化降解效率随pH的升高而增大,pH≤9时整体降解效率不高,pH=9时仅为16.39%,而pH=10时达到41.77%.臭氧和·OH共同参与降解氨氮的过程.单独臭氧氧化氨氮生成氮气的选择性具有pH依赖性,并与Cl~-密切相关.pH低(≤9)时,氨氮多以NH~+_4形态存在,O_3与Cl~-反应生成ClO~-_x(x=1、3),再氧化NH~+_4,从而生成气态产物N_2或N_2O.MgO在低温条件下具有很强的催化臭氧化降解氨氮的能力且温度升高有利于反应的进行,0、10、20℃时,MgO催化臭氧化氨氮的效率分别为77.53%、80.17%、91.26%.此过程中,·OH参与反应的程度低,一部分氨氮降解依靠ClO~-_x氧化NH~+_4,而氨氮降解的主要途径为O_3对NH_3的直接氧化.     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.