生物法处理含油钻井废水的影响因素研究

以含油钻井废水原浆为处理对象,研究了生物法处理过程中的相关影响因素.实验结果表明,氮、磷源是影响钻井废水中石油烃降解的重要因素,最佳氮、磷源及其加入量分别为(NH4)2SO4100 mg/L和KH2PO460 mg/L.在30～36℃,接种量15%,pH=6～8条件下处理72 h后可使钻井废水中的石油烃含量由805.6 mg/L下降到17.6 mg/L.     

废水污染物总量监测中采样方法的研究

通过对21家有代表性的废水污染源进行现场采样、排放曲线分析、采样频率优化的研究,确定总量监测中采样频率优化结果,为污染源总量控制监测提供技术指导。     

电絮凝技术处理洗车废水试验

采用电絮凝技术处理洗车废水,以保证处理后出水能够循环利用。考察电流密度、初始pH值、NaCl浓度及电解时间等操作因素对COD与浊度去除效果的影响。结果表明,在最佳处理条件下,出水达到生活杂用水水质标准;另外,去除COD过程符合一级动力学模型,去除单位浓度COD产生4.02×10-3kg湿污泥、3.10×10-4kg干污泥。     

稻田土菌群驯化对稻秆两步发酵产甲烷效果的影响

为提高稻秆的降解率及其厌氧发酵甲烷产量,采用高氨氮畜禽废水作为氮源以驯化稻田土壤微生物,优化其降解稻秆的初始pH值,并评估水解产物液体发酵产甲烷性能.结果表明,混合组驯化的微生物产纤维素酶活性及对稻秆木质素的降解率高于其它组及先前文献报道,分别达到4.01 IU和51.96%,且后期水解液中总有机碳（Total organic carbon, TOC）及还原糖含量最高.随着初始pH值的提高,稻秆中纤维素、半纤维素和木质素的降解率显著增加,稻秆水解液中的挥发性脂肪酸（Volatile fatty acids, VFAs）和TOC含量均显著增加,并在第7 d达到最高值.将水解稻秆7 d的水解液进行厌氧发酵显示,在初始pH=9.0条件下累积甲烷产量达到最大,为37.60 mL·mL^-1水解液.本实验结果表明, 驯化的稻田土微生物在碱性条件下可以更有效地降解稻秆,提高水解液中TOC及VFAs含量,从而提高厌氧发酵的甲烷产量.     

产酸脱硫反应器中碳硫比对群落生态特征的影响

通过产酸脱硫反应器处理高浓度含硫酸盐废水的连续流试验,从群落动态的角度研究碳硫比(COD/SO₄^2-)从4.2降低到2.0的过程中,pH值、氧化还原电位(ORP)、碱度(ALK)和末端产物(VFAs)组成、优势种群分布等群落生态特征的变化规律试验证明,在此过程中ORP和ALK提高,而pH值和VFAs中乙酸的分布比例降低,群落类型由高碳硫比稳定型转化为低碳硫比亚稳定型,但仍未改变乙酸型顶极群落的典型特征.     

聚丙烯酰胺对聚合物驱含油污水中油珠沉降分离的影响

研究发现阴离子聚丙烯酰胺(HPAM)对聚合物驱含油污水处理有正反2方面影响.聚合物能增加污水粘度,降低油珠上浮速度,而且聚合物能增加油水界面水膜强度,延缓油珠聚并时间,这是聚合物对油珠沉降分离的不利影响;同时,聚丙烯酰胺具有絮凝性,能将水中油珠连接到一起,有利于油珠聚并.当聚丙烯酰胺相对分子质量为2.72×10⁶,浓度小于800mg/L时,絮凝作用大于粘度作用,有利于油珠的沉降分离.初始油珠粒径小是聚合物驱含油污水难处理的主要原因.横向流除油器可以加速油珠聚并,缩短沉降时间,适合处理聚合物驱含油污水.     

地下渗滤处理村镇生活污水的中试

以红壤土作为填充土壤,在2cm/d的水力负荷下,进行了地下渗滤系统处理村镇生活污水的现场中试.结果表明,地下渗滤系统对COD、氨氮、总磷和总氮有着良好的去除效果,去除率分别达到84.7%、70.0%、98.0%和77.7%,出水COD、氨氮、总磷和总氮的平均浓度分别为11.7mg/L、4.0mg/L、0.04mg/L、4.7mg/L,达到建设部颁发的生活杂用水水质标准对总氮去除机理的分析表明,由硝化/反硝化实现生物脱氮是地下渗滤系统去除总氮的主要途径.在本中试系统中,反硝化效果良好但硝化效果不够理想,改善土壤环境以促进硝化作用是提高总氮去除率的关键.对土壤中氧化还原电位的测定结果表明,土壤内部的还原性质是阻碍硝化反应进行的主要原因.     

Recovery of Ni(II) from real electroplating wastewater using fixed-bed resin adsorption and subsequent electrodeposition

Resin adsorption and subsequent electrodeposition were used for nickel recovery. Treated wastewater can meet the Electroplating Pollutant Discharge Standard. The spent resin is completely regenerated by 3 BV of 4% HCl solution. 95.6% of nickel in concentrated eluent was recovered by electrodeposition. Effective recovery of high-value heavy metals from electroplating wastewater is of great significance, but recovering nickel ions from real electroplating wastewater as nickel sheet has not been reported. In this study, the pilot-scale fixed-bed resin adsorption was conducted to recover Ni(II) ions from real nickel plating wastewater, and then the concentrated Ni(II) ions in the regenerated solution were reduced to nickel sheet via electrodeposition. A commercial cation-exchange resin was selected and the optimal resin adsorption and regeneration conditions were investigated. The resin exhibited an adsorption capacity of 63 mg/g for Ni(II) ions, and the average amount of treated water was 84.6 bed volumes (BV) in the pilot-scale experiments. After the adsorption by two ion-exchange resin columns in series and one chelating resin column, the concentrations of Ni(II) in the treated wastewater were below 0.1 mg/L. After the regeneration of the spent resin using 3 BV of 4% (w/w) HCl solution, 1.5 BV of concentrated neutral nickel solution (>30 g/L) was obtained and used in the subsequent electrodeposition process. Using the aeration method, alkali and water required in resin activation process were greatly reduced to 2 BV and 3 BV, respectively. Under the optimal electrodeposition conditions, 95.6% of Ni(II) in desorption eluent could be recovered as the elemental nickel on the cathode. The total treatment cost for the resin adsorption and regeneration as well as the electrodeposition was calculated.     

Comparison of CNT-PVA membrane and commercial polymeric membranes in treatment of emulsified oily wastewater

CNT-PVA membrane was fabricated and compared with polymeric membranes. The separation performance was evaluated by homemade and cutting fluid emulsions. The three membranes show similar oil retention rates. CNT-PVA membranes have higher permeation fluxes compared with polymeric membranes. CNT-PVA membrane shows higher fouling resistance. Membrane separation is an attractive technique for removal of emulsified oily wastewater. However, polymeric membranes which dominate the current market usually suffer from severe membrane fouling. Therefore, membranes with high fouling resistance are imperative to treat emulsified oily wastewater. In this study, carbon nanotube-polyvinyl alcohol (CNT-PVA) membrane was fabricated. And its separation performance for emulsified oily wastewater was compared with two commercial polymeric membranes (PVDF membrane and PES membrane) by filtration of two homemade emulsions and one cutting fluid emulsion. The results show that these membranes have similar oil retention efficiencies for the three emulsions. Whereas, the permeation flux of CNT-PVA membrane is 1.60 to 3.09 times of PVDF membrane and 1.41 to 11.4 times of PES membrane, respectively. Moreover, after five consecutive operation circles of filtration process and back flush, CNT-PVA membrane can recover 62.3% to 72.9% of its initial pure water flux. However, the pure water flux recovery rates are only 24.1% to 35.3% for PVDF membrane and 6.0% to 26.3% for PES membrane, respectively. Therefore, CNT-PVA membrane are more resistant to oil fouling compared with the two polymeric membranes, showing superior potential in treatment of emulsified oily wastewater.     

工业废水毒性评估与致毒物质鉴别技术进展

综述了工业废水毒性的化学评估方法、生物毒性评估方法、毒性鉴定评估(TIE)程序以及效应引导的毒物鉴别分析(EDA)中污染物提取、分离、毒性测试、致毒物质识别等技术。指出,工业废水毒害风险评估方法正逐渐向化学分析与生物毒性测试相结合的关键致毒物质鉴别方法转变,便捷、高通量是致毒物质鉴别技术的发展方向,质谱技术及替代定性监测技术的发展将提供更为准确、便捷的致毒物质鉴别方法,为工业废水潜在风险防控提供依据。