膜蒸馏去除水中砷的研究

采用新型膜蒸馏技术对水中As（III）与As（Ⅴ）的去除展开了研究。实验结果表明,膜蒸馏对水中As (III)及As (Ⅴ)具有较高的去除能力：当产水中砷含量超过10 μg/L时,原水中As (III)与As (Ⅴ)的浓度可分别高达40 mg/L和2 000 mg/L。局部润湿现象的存在导致As (III)及As (Ⅴ)跨膜至产水侧,PVDF微孔膜在溶液中的负电性以及As (III)与 As (Ⅴ)在溶液中存在形式的不同导致膜蒸馏对两者去除能力的差异。360 h连续运行过程中产水通量及电导率稳定,且整个过程中As (III)均低于检测限,说明PVDF微孔膜具有良好的疏水性和稳定的除砷性能。     

好氧硝化颗粒污泥膜生物反应器性能和膜污染研究

实验研究了好氧硝化颗粒污泥膜生物反应器AGMBR的处理性能,并将其与活性污泥膜生物反应器ASMBR进行对比,考察了颗粒污泥在减缓膜污染中所起的作用.好氧硝化颗粒污泥膜生物反应器AGMBR连续稳定运行102 d,系统具有良好的去除有机物和同时硝化反硝化能力,在进水COD和NH+4-N浓度分别为500和200 mg/L时,COD、NH+4-N和TN的去除率分别稳定在86%、94%和45%以上.颗粒污泥有效减缓了膜污染,延长了膜清洗的周期,AGMBR中的膜污染以膜孔堵塞为主,占总阻力的64.81%;滤饼层的阻力为2.1×1012m-1,远小于ASMBR中的16.07×10"m-1;膜清洗周期是相同条件下ASMBR的2.43倍以上;而且AGMBR内不断有新颗粒生成,维持了AGMBR系统性能和运行的稳定.     

微曝气Fenton氧化法处理模拟双酚A废水的效果及其生物验证

研究了微曝气Fenton氧化法关键工艺参数对模拟双酚A（BPA）废水处理效果的影响,并从活性污泥性质和污染物去除率两方面,采用膜生物反应器(membrane bioreactor, MBR)对微曝气Fenton氧化法的处理效果进行了实验验证,为实现BPA废水的生物处理奠定基础。结果表明,初始pH值、反应时间、H₂O₂/COD(质量浓度比)、H₂O₂/Fe²⁺ (摩尔浓度比)、反应温度及曝气量均对预处理效果有较大影响,在最佳条件下,COD去除率可达70%,BOD/COD值则由原废水的0.02提高到0.50以上。MBR处理上述出水的结果表明,经微曝气Fenton氧化处理BPA的废水,可较好地适应后续的生化处理。     

SRT对MBR污泥性质的影响

以浸没式膜-生物反应器(SMBR)处理模拟赖氨酸废水为研究体系,考察SRT在10、20和40 d条件下,SMBR中的胞外聚合物(EPS)组分和含量、污泥沉降性能和污泥相对疏水性等污泥性质的变化及其对膜污染的影响。结果表明,随着SRT的延长,混合液中EPS总量呈递减趋势,TBEPS中蛋白质与多糖的比值呈上升趋势,污泥的沉降性能变差,相对疏水性增强;膜通量下降速率变大,膜污染加重。污泥性质与膜污染的相关性表明,膜污染与蛋白质和多糖的比值、污泥沉降性能和相对疏水性呈正相关关系,而与EPS呈负相关关系。     

氯酚与富里酸的缔合作用

本文用超滤膜方法证实氯酚与富里酸之间存在缔合作用,并计算出表观缔合常数在２．７＊１０＾３－－１２１＊１０＾３ｍｌ．ｇ＾－１范围内。实验结果表明”ＰＨ、富里酸含量,氯酚取代氯原子个数都能够影响Ｋ值的大小。     

Dynamic contact angle effects on gas-liquid behaviors in the cathode of proton exchange membrane fuel cell with stirred tank reactor design

Liquid water management is still a critical issue in the improvement of proton exchange membrane fuel cell (PEMFC) performance. In this work, for the first time, the liquid water behavior and transport inside the cathode of a PEMFC with a stirred tank reactor (STR) design, rather than the conventional PEMFC flow channel design, are numerically studied. The dynamic contact angle (DCA) is applied to multiple wall boundaries in the numerical model through a user-defined-function (UDF) code, i.e., STR-DCA model. Another numerical model with the static contact angle (SCA) and same operating conditions, i.e., STR-SCA model, is also developed for comparison. The volume of fluid (VOF) method is employed in the simulation to track the gas-liquid interface. The results show that the liquid water distribution and transport are significantly different between these two models, indicating the remarkable effects of DCA on the simulation results. It is also verified the capability of STR-PEMFC to reduce the liquid water flooding, showing the potential of this channel-less type fuel cell in the further development.     

Review: recent advances in biogas purifying technologies

Biomethane production through biogas upgrading is a promising renewable energy for some industries which could be part of the equilibrium needed with fossil fuels consumption to achieve a sustainable society. This paper presents a comprehensive list of biogas upgrading technologies focused on carbon dioxide removal as well as recent advances reported by researcher with wide expertise in this topic. Additionally, an extensive costs–performance comparison among the technologies studied is discussed. Among the different alternatives, chemical scrubbing stood out to achieve high biomethane purities while cryogenic technologies proved to be effective against methane losses. Regarding the different costs, water scrubbing and membrane separation seem to be the most affordable techniques.     

集成膜法水处理工艺的研究与应用

集成膜法除盐系统具有连续产水、出水质量好、易控制、占地少、不需酸碱、利于环保等优点。文章通过对集成膜法水处理技术进行研究与应用,将原有的化学除盐水处理方式改为集成膜法水处理工艺,该方法产水水质高且水质稳定,每年可节约酸碱200 t,阴、阳离子交换树脂10 t,切实解决电厂所面临的产水水质不稳定、酸碱废液排放等问题,有力推动了清洁生产。     

PM2.5在线监测技术概述

针对PM2.5颗粒物监测技术和PM2.5的监测网络的建设,重点介绍了美国多年来对PM2.5的监测状况,以及采用的Beta射线法、Beta射线光浊度法、微量振荡天平法等监测技术的方法和原理;指出综合国内外多年的监测经验,PM2.5的在线监测需要经过大量手工经典方法数据作为比对和校验,才能给出有效而高质量的PM2.5监测数据。     

Simulation studies of ammonia removal from water in a membrane contactor under liquid–liquid extraction mode

Simulation studies were carried out, in an unsteady state, for the removal of ammonia from water via a membrane contactor. The contactor had an aqueous solution of NH₃ in the lumen and sulphuric acid in the shell side. The model equations were developed considering radial and axial diffusion and convection in the lumen. The partial differential equations were converted by the finite difference technique into a series of stiff ordinary differential equations w.r.t. time and solved using MATLAB. Excellent agreement was observed between the simulation results and experimental data (from the literature) for a contactor of 75 fibres. Excellent agreement was also observed between the simulation results and laboratory-generated data from a contactor containing 10,200 fibres. Our model is more suitable than the plug-flow model for designing the operation of the membrane contactor. The plug-flow model over-predicts the fractional removal of ammonia and was observed to be limited when designing longer contactors.