Rapid detection of multiple class pharmaceuticals in both municipal wastewater and sludge with ultra high performance liquid chromatography tandem mass spectrometry

This work described the development, optimization and validation of an analytical method for rapid detection of multiple-class pharmaceuticals in both municipal wastewater and sludge samples based on ultrasonic solvent extraction, solid-phase extraction, and ultra high performance liquid chromatography-tandem mass spectrometry quantification. The results indicated that the developed method could effectively extract all the target pharmaceuticals （25） in a single process and analyze them within 24 min. The recoveries of the target pharmaceuticals were in the range of 69%-131% for wastewater and 54%-130% for sludge at different spiked concentration levels. The method quantification limits in wastewater and sludge ranged from 0.02 to 0.73 ng/L and from 0.02 to 1.00μg/kg, respectively. Subsequently, this method was validated and applied for residual pharma- ceutical analysis in a wastewater treatment plant located in Beijing, China. All the target pharmaceuticals were detected in the influent samples with concentrations varying from 0.09 ng/L （tiamulin） to 15.24 μg/L （caffeine）; meanwhile, up to 23 pharmaceuticals were detected in sludge samples with concentrations varying from 60 ng/kg （sulfamethizole） to 8.55 mg/kg （ofloxacin）. The developed method demonstrated its selectivity, sensitivity, and reliability for detecting multiple-class pharmaceuticals in complex matrices such as municipal wastewater and sludge.     

工艺过程源和溶剂使用源挥发性有机物排放成分谱研究进展

工艺过程源和溶剂使用源是我国大气挥发性有机物(VOCs)最主要的工业来源,近年来源成分谱的研究逐步受到重视.本文总结梳理了2000年以来国内外有关工艺过程源和溶剂使用源排放VOCs特征的相关研究,对比分析了不同研究结果的差异,结合不同研究的对象和方法,探讨了影响溶剂使用和工艺过程源排放成分谱研究的主要影响因素.结果表明,工艺过程源下分的32个三级子类(参照国家《大气挥发性有机物源排放清单编制技术指南》源分类方法)中,有相关研究报道的包括八类;溶剂使用源下分的10个三级子类中,有相关研究报道的包括四类.总体而言,细化的行业研究种类比较少,不同行业排放VOCs组成差异大,可比性较差.污染源采集测试方法对同一行业源排放成分谱研究结果有较大影响.此外,成分谱中VOCs物质名录的不统一也不利于不同研究结果的比较;含氧VOCs是上述两类污染源排放的重要组分,需要纳入测量范围.未来,有必要建立开放交互式的工艺过程源和溶剂使用源排放VOCs成分谱库平台,鼓励并形成不同研究结果的共享及录入机制;并建立相关研究成果数据入库规范,包括研究的对象、方法、地区、时段以及样本量等详细信息,以便开展不同VOCs源成分谱不确定性评判.     

加速溶剂萃取/气相色谱质谱法测定鱼类样品中的多环麝香

建立了鱼类样品中5种多环麝香的分析方法.采用加速溶剂萃取(ASE)提取,经凝胶渗透色谱(GPC)以及中性氧化铝层析柱净化后,浓缩并定容洗脱液,用GC-SIM-MS进行检测.本方法对替代物标样荧蒽-d10.的回收率为92.7%-112.9%.以六氯苯(13C)为内标,5种合成麝香的线性范围为1.0-1000.0 ng·g...     

载磷Mg/Al/Fe-LDO的微波辅助溶剂解吸方法特性

针对载磷Mg/Al/Fe-LDO再生利用与解吸液富集回收磷的问题,通过对比直接溶剂解吸法与微波辅助溶剂解吸法在解吸条件、吸附性能与材料层状结构恢复方面的差异,考察了微波辅助溶剂解吸方法的技术特性,并分析了其解吸机制.结果显示,与直接溶剂解吸法相比,微波辅助溶剂解吸法解吸时间由4 h缩短为10～30 min,解吸效果提高15%以上;在同等解吸效果前提下,组合解吸剂(Na_2CO_3+NaOH)浓度降低2倍;解吸剂用量减少10倍.载磷Mg/Al/Fe-LDO经微波辅助溶剂解吸-焙烧再生后,吸附性能得到较好地恢复,3次吸附-解吸-焙烧后再生率接近90%,比直接溶剂解吸-焙烧再生提高40%.由于微波能够强化溶剂离子热运动、促进离子传质与扩散过程,加快离子交换速率,有利于材料层状结构的有效恢复,因此,微波辅助溶剂解吸法能够在较低解吸剂浓度与用量条件下,实现对载磷Mg/Al/Fe-LDO的高效、快速解吸,有利于污水中磷的富集回收.     

A new procedure combining GC-MS with accelerated solvent extraction for the analysis of phthalic acid esters in contaminated soils

An optimized procedure based on gas chromatography-mass spectrometry (GC-MS) combined with accelerated solvent extraction (ASE) is developed for the analysis of six phthalic acid esters (PAEs), which are priority soil pollutants nominated by United States Environmental Protection Agency (USEPA). Quantification of PAEs in soil employs ultrasonic extraction (UE) (USEPA 3550) and ASE (USEPA 3545), followed by clean up procedures involving three different chromatography columns and two combined elution methods. GC-MS conditions under selected ion monitoring (SIM) mode are described and quality assurance and quality control (QA/QC) criteria with high accuracy and sensitivity for target analytes were achieved. Method reliability is assured with the use of an isotopically labeled PAE, di-n-butyl phthalate-d4 (DnBP-D4), as a surrogate, and benzyl benzoate (BB) as an internal standard, and with the analysis of certified reference materials (CRM). QA/QC for the developed procedure was tested in four PAE-spiked soils and one PAE-contaminated soil. The four spiked soils were originated from typical Chinese agricultural fields and the contaminated soil was obtained from an electronic waste dismantling area. Instrument detection limits (IDLs) for the six PAEs ranged 0.10–0.31 μg·L^-1 and method detection limits (MDLs) of the four spiked soils varied from a range of 20–70 μg·kg^-1 to a range of 90– 290 μg·kg^-1. Linearity of response between 20 μg·L^-1 and 2 mg·L^-1 was also established and the correlation coefficients (R) were all>0.998. Spiked soil matrix showed relative recovery rates between 75 and 120% for the six target compounds and about 93% for the surrogate substance. The developed procedure is anticipated to be highly applicable for field surveys of soil PAE pollution in China.     

温和湿热预处理对稻秸理化特性及生物产沼气的影响

为考察温和湿热预处理提高秸秆产气速率的可行性,以水稻秸秆为原料,在湿热预处理温度80℃、物料含水率60%条件下,通过分析湿热处理前后稻秸理化特性及厌氧生物产气特性的变化,研究不同湿热预处理时间对秸秆预处理及产沼气效果的影响.结果表明,温和湿热预处理促进了稻秸有机物的溶出,预处理后稻秸水浸提液pH值有较大幅度下降,而COD、TVFA和乙酸含量均大幅度增加,与对照组相比,T1、T2和T3处理秸秆水浸提液COD浓度分别增加了47.19%、55.18%和60.62%,TVFA浓度分别增加了22.34%、33.98%和50.12%,乙酸浓度分别增加了19.52%、34.02%和49.37%,并且乙酸占TVFA百分比均超过85%以上,差异显著性分析表明,处理T1水浸提液各理化特性指标与对照组相比呈极显著差异,而不同温和湿热预处理之间无显著差异;对稻秸纤维素组分破坏效果明显,但不同预处理时间对秸秆木质纤维组分破坏效果影响不大;厌氧发酵产气的结果表明,温和湿热预处理可明显提高稻秸厌氧生物产沼气,发酵20 d平均容积产气率可提高12.53%以上,累积TS产气率可提高36.17%以上.可见,温和湿热预处理提高秸秆厌氧生物产沼气效果是可行的,考虑到工程应用中预处理能耗成本因素,湿热预处理时间以T1处理(即6 h)为宜.     

温和水热预处理促进秸秆产沼气的条件优化研究

以水稻秸秆为原料,在前期单因素试验基础上,通过正交试验研究不同水热预处理条件对稻秸理化特性及产沼气效果的影响.结果表明,预浸时间、初始含水率和热处理时间3个因素对稻秸厌氧发酵20d累积TS产气率的影响程度各不相同,各因素对厌氧发酵累积TS产气率的影响大小顺序为初始含水率 >预浸时间 >热处理时间;得出的最佳水热预处理条件为：初始含水率为55%,预浸时间为2h,热处理时间为6h;与处理CK相比,最佳预处理条件下稻秸20d容积产气率提高29.79%,产气量达总产气量60%和80%时间可提前5d;结合预处理前后稻秸理化特性变化规律分析,表明温和水热预处理促进了纤维素和半纤维素的降解溶出,并促使其更多转化为挥发性脂肪酸（VFA）,从而有利于稻秸快速产沼气.     

北京地区地表水中OCPs和PCBs的污染分析

在夏、冬两季对北京地区密云,潮白河,玉渊潭和通惠河等地表水中17种有机氯农药（OCPs）和84种多氯联苯（PCBs）的含量进行了分析及来源解析.实验结果表明,OCPs总量在7.86～53.1ng/L之间,平均值为（16.9±14.6）ng/L.PCBs总量在2.99～32.7ng/L之间,平均浓度为（10.9±10.4）ng/L.HCHs,硫丹,DDTs和HCB是主要的OCPs污染物,其含量分别为（13.9±11.5）ng/L,（2.20±2.01）ng/L,（0.63±1.51）ng/L和（0.12±0.14）ng/L.α-HCH/γ-HCH平均比值为1.53,小于工业HCH中比值4～7,表明北京地区地表水中存在林丹的使用.而DDT/（DDD+DDE）比值<1.22,表明北京地区并无新的DDTs污染源输入环境.PCBs以低氯代联苯为主,其中二氯,三氯,四氯和五氯联苯总和占∑₈₄PCBs总量的79.2%.北京地区地表水中不同氯取代数PCBs组成与我国历史PCB产品组成相符,均以低氯代联苯为主,表明北京地区地表水中PCBs污染来源为历史使用.相比于国内其他区域水质而言,北京地区地表水OCPs和PCBs污染水平较低.     

干化罐底油泥的溶剂萃取-海水洗涤工艺

为节约淡水资源、拓展海水的直接利用途径,采用热化学水洗处理技术开展了基于海水洗涤的罐底油泥处理试验研究. 结果表明:干化罐底油泥(水含量为9.8%、油含量为25.6%、固含量为64.6%,均以w计)不宜直接进行热化学洗涤,需采用轻油(120#溶剂油)进行萃取预处理,萃取后残油量(干基,以w计)为18.8%. 适宜的洗涤液为海水溶液,其ρ(TX-10)(TX-10为壬基酚聚氧乙烯醚)为10 g/L. 液固质量比为5、洗涤温度为60 ℃、搅拌速率为180 r/min、搅拌时间为30~40 min是洗涤萃取残泥的适宜条件,该条件下萃取后的残油量为2.80%. 二级海水洗涤可使残油量降至0.23%,满足GB 4284—1984《农用污泥中污染物控制标准》. 在洗涤废水再利用试验中,为维持洗涤废水的脱油能力,可在每L洗涤废水中补加1 g TX-10. 研究显示,溶剂萃取-海水洗涤工艺可有效处理干化罐底油泥.      

铜镍电镀退镀废液资源化处理工艺

针对硝酸型铜镍退镀废液,确定了蒸馏法回收硝酸、溶剂萃取法分离提取铜、沉淀分离法回收镍的工艺路线.探讨了采用P507煤油体系萃取分离硝酸介质中的铜和镍及用硫酸反萃铜的条件及影响规律,确定了最佳工艺参数.结果表明,硝酸回收率可达97.8%;当最佳萃取工艺条件为:料液浓度Cu 15～20mg/mL,Ni 5～10 mg/mL,料液pH为1～2,萃取剂体积分数35%,皂化度60%,相比为1∶1,振荡时间2min,温度20℃～25℃,铜的一级萃取率达90%以上,铜镍分离系数为75,经过三级逆流萃取废液中的铜镍已达到完全分离;以NaOH作沉淀剂,溶液的pH为10～11,镍的回收率可达99.9%.经上述处理后,使排放液达到国家工业废水排放标准要求.