土壤溶解性有机质荧光特征及其与铜的络合能力

选取4种不同类型土壤和腐熟鸡粪,透析提取溶解性有机质(DOM),通过凝胶色谱、三维荧光光谱测定并分析了DOM的相对分子质量(M_r)分布、化学结构特征及其与铜的结合能力.结果表明,鸡粪DOM相对分子质量积分面积远高于其他样品,表现出其具有较高的有机物含量,泥炭土次之.暗棕壤、褐土和黑土较低,仅为鸡粪积分面积的4.5%~5%.鸡粪在中分子量段积分面积约占总物质的34.1%,低分子量段和高分子量段分别约占41.7%和24.2%.荧光光谱分析表明,各样品均出现类蛋白荧光峰(E_x/E_m=240~270/300~350 nm),在中、高分子量段(M_r500)暗棕壤存在的荧光峰消失.泥炭土出现了较为独特的可见光区类富里酸荧光峰(E_x/E_m=325/420 nm),该荧光峰和黑土的荧光峰在中、高分子量段(M_r500)都产生了红移现象.鸡粪分别出现了和黑土类似的紫外区类富里酸荧光峰,以及和泥炭土类似的可见光区类富里酸荧光峰,以及一类独特的类蛋白荧光峰(E_x/E_m=280/350 nm),但这种类蛋白荧光峰在中分子量段(500M_r12 000)消失.分析表明泥炭土与Cu的络合常数(lg K)为4.13,其他3种土壤与Cu的络合常数较小且差别不大,集中在2.10~3.10之间.鸡粪与Cu的结合能力最大,络合常数达到6.66.     

紫色水稻土颗粒有机质对重金属的富集特征

在重庆合川区和铜梁区随机采集了20个紫色水稻土,将其分成颗粒有机质(0.053~2 mm,POM)、砂粒(0.053~2mm)和细土(0.053 mm)这3个组分,通过比较不同组分的有机碳及重金属(Cu、Zn、Pb、Cd)含量和分布状况,研究了紫色水稻土中POM对重金属的富集特征及其与土壤理化性质如pH、CEC、黏粒和土壤有机碳(SOC)等的关系.结果表明,采样区紫色水稻土的POM含量范围为7.31~44.76 g·kg~(-1),平均值为19.20 g·kg~(-1),有机碳含量为96.61~263.17 g·kg~(-1),平均值为151.34 g·kg~(-1),显著高于原土及其他组分,对土壤有机碳的贡献率为8.63%~48.62%,代表了一大部分土壤有机碳库.POM中的Cu、Zn、Pb和Cd平均富集系数分别为3.35、1.14、2.88和2.14,显著高于其他组分,表现出一定的富集作用,对上述重金属的贡献率分别为6.02%、2.22%、5.24%和3.21%,POM对Cu、Pb的富集能力和贡献率均显著大于Zn和Cd.相关分析结果表明,POM含量与SOC、pH、CEC、黏粒(0.002 mm)呈显著或极显著正相关,SOC是主要因素.POM-C含量与总量分别与黏粒含量、SOC呈显著相关.POM中重金属总量与SOC、pH、POM-C总量呈显著或极显著正相关,SOC是最关键因子;与其他重金属相比,Zn在POM中的总量与土壤性质的回归系数最高,关系最为密切.     

上海一次典型雾霾过程中不同天气现象的气溶胶光学特性及转化机制

以上海市2013年冬季一次持续雾霾过程为例,根据能见度和相对湿度的地面观测资料将雾霾过程划分为干霾、湿霾、雾3种不同天气现象,对不同天气现象的气溶胶光学特性垂直分布特征进行了研究,并初步分析不同天气现象的转化机制.结果表明,3种不同天气现象的发生顺序为湿霾→干霾→湿霾及湿霾→雾→干霾→湿霾,相对湿度对能见度的影响最大,温度次之,再次是风速,而PM_(2.5)对能见度的影响最小.CALIPSO(Cloud Aerosol Lidar and Infrared Pathfinder Satellite Observation)探测期间,存在2~3 km明显气溶胶层,且不同天气现象的气溶胶层厚度不同(雾湿霾干霾);雾霾发生期间,1.0 km以下高度气溶胶消光能力最大;在干霾、湿霾到雾的转化过程中,球形、大粒径气溶胶增多,非球形、小粒径气溶胶减少.     

生活垃圾源头沥水的减量提质效应研究

针对我国生活垃圾厨余组分含量高、含水率高和热值低的特点,提出以降低厨余组分含水率为主要手段,实现生活垃圾源头减量和提质为主要目标的源头沥水和选择性分质收集模式.在苏州市两个居民小区进行了为期10个月的项目试点,监测结果显示,居民家庭采取源头沥水措施后,生活垃圾产生量减少6.47%,含水率降低2.23%,低位热值提高10.94%.生活垃圾源头沥水的减量提质效应良好,有助于提高后续焚烧及填埋处理设施运行效率和二次污染控制水平,降低运输及处理成本.     

纤维素降解菌Arthrobacter oryzae HW-17的纤维素降解特性及纤维素酶学性质

采用单一碳源选择性培养基和纤维素平板水解圈法筛选到一株具有较强纤维素分解能力的菌株Arthrobacter oryzae HW-17.此外,高通量测序发现,不同驯化条件下微生物群落结构有明显差异,低温条件下优势属为类芽孢杆菌属(Paenibacillus)和伯克氏菌属(Burkholderia).本文同时对菌株Arthrobacter oryzae HW-17的微生物特性和纤维素降解特性进行了初步研究,结果发现,KNO_3、30或35℃、pH=7分别为菌株产纤维素酶的最佳氮源、温度和pH.菌株HW-17的最高纤维素酶活为18.55 U·m L~(-1),且对磨碎加工处理的纤维素样品和含鸡粪的纤维素混合样品有更好的降解效果.此外,菌株HW-17产生的纤维素酶在中温(≤50℃)和偏酸性(pH=5~7)条件下能保持较高的酶活.Cu(Ⅱ)和Pb(Ⅱ)等金属离子能够抑制该酶的活性.     

Mercury pollution in a mining area of Guizhou,China: Fluxes over contaminated surfaces and concentrations in air,biological and geological samples

A dynamic flux chamber has been used to estimate fluxes of mercury over different types of surfaces in an abandoned open‐cut mine of Tongren prefecture, Guizhou province, China during spring and summer of 1996. The highest fluxes were obtained over cinnabar slag and contaminated soils, whereas the emissions above cinnabar ore were substantially lower. These fluxes was scaled up to estimate the contribution of mercury emissions to air from mercury wastes, compared to anthropogenic activities in the province of Guizhou, China. Atmospheric mercury concentrations measured were enhanced in the mining area (<1.3 μg m^‐3) compared to regional background sites (1.8–5.1 ng m^‐3). The spreading of mercury was estimated by using biological and geological samples. Moss bags have been employed to estimate long‐time dry‐ and wet‐deposition to this area.     

Utilization of cement kiln dust (CKD) in cement mortar and concrete—an overview

Solid waste management is one of the major environmental concerns around the world. Cement kiln dust (KKD), also known as by-pass dust, is a by-product of cement manufacturing. The environmental concerns related to Portland cement production, emission and disposal of CKD is becoming progressively significant. CKD is fine-grained, particulate material chiefly composed of oxidized, anhydrous, micron-sized particles collected from electrostatic precipitators during the high temperature production of clinker. Cement kiln dust so generated is partly reused in cement plant and landfilled. The beneficial uses of CKD are in highway uses, soil stabilization, use in cement mortar/concrete, CLSM, etc.Studies have shown that CKD could be used in making paste/mortar/concrete. This paper presents an overview of some of the research published on the use of CKD in cement paste/mortar/concrete. Effect of CKD on the cement paste/mortar/concrete properties like compressive strength, tensile strength properties (splitting tensile strength, flexural strength and toughness), durability (Freeze–thaw), hydration, setting time, sorptivity, electrical conductivity are presented. Use of CKD in making controlled low-strength materials (CLSM), asphalt concrete, as soil stabilizer, and leachate analysis are also discussed in this paper.     

Radiation Effects on Blends of Poly(ε-Caprolactone) and Diatomites

Poly(-caprolactone) (PCL) was blended with diatomaceous earth (diatomite) and irradiated with -rays to introduce cross-linking between PCL molecules or both components. The unwashed diatomite containing a little of a volatile component showed high efficiency of introduction of cross-linking, whereas that with no volatile component showed low efficiency of introduction of cross-linking. Elongational viscosity, melt viscosity, and modulus of PCL/diatomite blend irradiated at various doses were significantly improved. Enzymatic degradation of the PCL/diatomite blend became faster than that of the PCL, though that of the blend irradiated became slower.     

Influences of Magnesium <Emphasis Type="Italic">tri-</Emphasis>Silicate on the Physical,Mechanical, and Degradable Properties of Ultraviolet (UV) Radiation Cured Plain Board Surface

A series of formulations were prepared with different percentages of oligomer, epoxy diacrylate (EA-1020 ), monomer, 1,6 Hexane diol diacrylate,(HDDA) and different percentages of filler (Magnesium tri-silicate, Mg₂Si₃O₈). Irgacure 369 [2-Benzyl-2-dimethyl-amine-1 (4-morpholinophenyl) butanone-1] was used in the formulations as photoinitiator. Ultraviolet (UV) cured thin polymer films were prepared from these formulating solutions on clean glass plates. Pendulum hardness (PH), gel content and macro scratch hardness (MSH) of the UV cured films were studied. One percent Mg₂Si₃O₈ containing formulation showed the premium properties. The substrates (plain board) were coated by these formulating solutions and cured under the same UV lamp at different intensities of radiation. Various properties of the coated surface such as PH, gloss, adhesion, abrasion and MSH were investigated. The base coat containing 1% Mg₂Si₃O₈ and top coat containing 48% HDDA produced the best performance among all the formulations inspected. The degradable properties in different weathering conditions on PH, gloss, adhesion, abrasion and MSH were measured. The surface cured with the optimized formulation (E) again yielded the minimum loss of the properties.