吸力式桶形基础多桶组合结构承载力特性研究

海洋采油平台结构中一般采用多桶组合基础型式,然而迄今对多桶组合结构尚缺乏理论分析和实验研究。本文针对我国第一座吸力式桶形基础采油平台CB20B,基于单桶基础在复合加载模式下的承载力特性,建立了双桶、四桶组合基础的三维有限元数值计算模型,探讨了对称多桶基础结构与单桶基础结构的承载力特性之间的相互关系,阐述了不同桶间距的多桶组合结构地基破坏机制,为工程设计提供参考依据。     

The Contribution of Marsh Zones to Water Quality in Dutch Shallow Lakes: A Modeling Study

Many lakes have experienced a transition from a clear into a turbid state without macrophyte growth due to eutrophication. There are several measures by which nitrogen (N) and phosphorus (P) concentrations in the surface water can be reduced. We used the shallow lake model PCLake to evaluate the effects of three measures (reducing external nutrient loading, increasing relative marsh area, and increasing exchange rate between open water and marsh) on water quality improvement. Furthermore, the contribution of different retention processes was calculated. Settling and burial contributed more to nutrient retention than denitrification. The model runs for a typical shallow lake in The Netherlands showed that after increasing relative marsh area to 50%, total phosphorous (TP) concentration in the surface water was lower than the Maximum Admissible Risk (MAR, a Dutch government water quality standard) level, in contrast to total nitrogen (TN) concentration. The MAR levels could also be achieved by reducing N and P load. However, reduction of nutrient concentrations to MAR levels did not result in a clear lake state with submerged vegetation. Only a combination of a more drastic reduction of the present nutrient loading, in combination with a relatively large marsh cover (approximately 50%) would lead to such a clear state. We therefore concluded that littoral marsh areas can make a small but significant contribution to lake recovery.     

不同条件下高炉渣吸附水中无机磷的研究

高炉渣(BFS)是在冶炼生铁过程中产生的固体废弃物,开展高炉渣的资源化研究具有重要意义.为了对水淬高炉渣净化含磷污水的应用提供理论依据,采取等温吸附的实验方法,比较了不同水淬炉渣的吸附磷效果,研究了不同pH和不同温度下水淬炉渣吸附磷的特点,结果如下:利用Langmuir等温吸附方程炉渣吸附磷的过程进行拟合,其相关系数均能达到显著水平.炉渣的碱度越高,吸附磷的效果越好;炉渣对磷的吸附能力随溶液pH的增加而降低,且初始为酸性(pH=2、4)的溶液在吸附达到平衡后pH有所上升,而初始为碱性的溶液(pH=10、12)在吸附达到平衡后pH有所下降;炉渣对磷的吸附是一个自发放热过程.     

水力负荷对厌氧氨氧化反应器运行影响的研究

采用一套有效容积为4.46 L的UASB-ANAMMOX反应器,通过对水力负荷进行3个阶段的调节,研究水力停留时间对ANAMMOX反应器处理效果的影响.3个阶段的水力负荷分别为0.20～0.25、0.38～0.43、0.16～0.20 L/(Ld).在试验过程中,水力负荷的冲击对NH 4-N、NO-2-N的去除率影响明显.其中水力负荷为0.20～0.25 L/(L·d)时,NH 4-N、NO-2-N去除率都能达到99%以上;当水力负荷为0.38～0.43 L/(L·d)时,NH 4-N、NO-2-N去除率分别降至64%和62%;当水力负荷为0.16～0.20 L/(L·d)时,NH 4-N、NO-2-N去除率立刻分别回升至94%和97%.ANAMMOX反应过程中,NO-2-N和NH 4-N的去除量比值基本在1.3∶1.0左右变化,ANAMMOX反应的优势菌种代谢在运行过程中会将一部分NO-2-N转化为NO-3-N,水力负荷的改变对NO-3-N的出水浓度影响不大;但NO-3-N日生成量与水力负荷的大小成正比.试验表明,UASB-ANAMMOX反应器对水力负荷冲击有较强的抵抗力,但是仍会造成一定量的ANAMMOX反应的优势菌流失,使该反应器在短时间内不能恢复最佳的去除效果.     

Potential environmental impact of dissolution of raw phosphate in sea water of the Gulf of Aqaba

Dissolution of raw phosphate (apatite) in sea water of the Gulf of Aqaba was investigated through lab incubation experiments. Three types from three different sources (Al-Hasa, Al-Abyad and Esh-Shydiya) have been used for these experiments. Impact of quantity, grain size, and source (type) of raw phosphate on dissolution rate were studied. Statistical analysis shows significant differences between the results obtained from comparing each two weights; as weight of apatite increased, dissolved inorganic phosphate-phosphorus (DIP) and fluoride in sea water solution increased. The differences between the dissolution rates of raw phosphate from the three sites were not significant while the differences between the different grain size fractions were significant. Dissolution rates were inversely related to particle size. Using a worst-case scenario, a conservative estimate of the maximum increase in DIP in seawater of the Gulf of Aqaba due to the apatite particles lost to the sea during ship loading resulted in DIP concentrations of 0.03 μM per year. As the residence time of the water in the Gulf of Aqaba is about one year, the DIP concentration will not increase by more than 0.03 μM under the estimated annual quantity of exported phosphate. Fluoride will not increase by more than 0.03 mg/l under the same conditions.     

有效磷含量对硝酸铵溶液热安全性的影响

为了了解硝酸磷肥生产过程中,硝酸铵溶液中加入磷酸一铵的安全性,通过自制实验装置,研究了有效磷含量对质量分数为85%的硝酸铵溶液热分解的影响。结果表明,质量分数为85%的硝酸铵和磷酸一铵混合溶液的临界爆炸温度高于纯质量分数为85%的硝酸铵溶液,稳定性更好;磷酸一铵抑制硝酸铵的热分解,随着有效磷含量的增加,硝酸铵混合溶液临界爆炸温度升高;升温速率对硝酸铵混合溶液的临界爆炸温度影响很大,随着升温速率由2℃/min升高到3℃/min,质量分数为85%的硝酸铵混合溶液的临界爆炸温度升高,不易发生爆炸,安全性更好。研究结果对硝酸磷肥的生产安全有一定的指导意义。     

磷酸银/树脂复合物的制备及其对亚甲基蓝的光催化降解

以聚乙烯吡咯烷酮(PVP)为稳定剂,采用化学沉积法制备了磷酸银/树脂复合物,降解亚甲基蓝,研究其光催化活性,并对样品进行了XRD和SEM表征。探讨了不同的光源、催化剂投加量、PVP含量、p H值等因素对亚甲基蓝降解率的影响。结果表明,在太阳光(夏天早上9点到11点的阳光)下,偏酸介质中,催化剂用量为0.8 g/L,PVP质量分数为0.01%的磷酸银/树脂复合物,液面高度为15 cm的条件下对亚甲基蓝有最佳降解效果。     

Injuries in Full-Scale Vehicle Side Impact Moving Deformable Barrier and Pole Tests Using Postmortem Human Subjects

Objective: To conduct near-side moving deformable barrier (MDB) and pole tests with postmortem human subjects (PMHS) in full-scale modern vehicles, document and score injuries, and examine the potential for angled chest loading in these tests to serve as a data set for dummy biofidelity evaluations and computational modeling.

Methods: Two PMHS (outboard left front and rear seat occupants) for MDB and one PMHS (outboard left front seat occupant) for pole tests were used. Both tests used sedan-type vehicles from same manufacturer with side airbags. Pretest x-ray and computed tomography (CT) images were obtained. Three-point belt-restrained surrogates were positioned in respective outboard seats. Accelerometers were secured to T1, T6, and T12 spines; sternum and pelvis; seat tracks; floor; center of gravity; and MDB. Load cells were used on the pole. Biomechanical data were gathered at 20 kHz. Outboard and inboard high-speed cameras were used for kinematics. X-rays and CT images were taken and autopsy was done following the test. The Abbreviated Injury Scale (AIS) 2005 scoring scheme was used to score injuries.

Results: MDB test: male (front seat) and female (rear seat) PMHS occupant demographics: 52 and 57 years, 177 and 166 cm stature, 78 and 65 kg total body mass. Demographics of the PMHS occupant in the pole test: male, 26 years, 179 cm stature, and 84 kg total body mass. Front seat PMHS in MDB test: 6 near-side rib fractures (AIS = 3): 160–265 mm vertically from suprasternal notch and 40–80 mm circumferentially from center of sternum. Left rear seat PMHS responded with multiple bilateral rib fractures: 9 on the near side and 5 on the contralateral side (AIS = 3). One rib fractured twice. On the near and contralateral sides, fractures were 30–210 and 20–105 mm vertically from the suprasternal notch and 90–200 and 55–135 mm circumferentially from the center of sternum. A fracture of the left intertrochanteric crest occurred (AIS = 3). Pole test PMHS had one near-side third rib fracture. Thoracic accelerations of the 2 occupants were different in the MDB test. Though both occupants sustained positive and negative x-accelerations to the sternum, peak magnitudes and relative changes were greater for the rear than the front seat occupant. Magnitudes of the thoracic and sternum accelerations were lower in the pole test.

Conclusions: This is the first study to use PMHS occupants in MDB and pole tests in the same recent model year vehicles with side airbag and head curtain restraints. Injuries to the unilateral thorax for the front seat PMHS in contrast to the bilateral thorax and hip for the rear seat occupant in the MDB test indicate the effects of impact on the seating location and restraint system. Posterolateral locations of fractures to the front seat PMHS are attributed to constrained kinematics of occupant interaction with torso side airbag restraint system. Angled loading to the rear seat occupant from coupled sagittal and coronal accelerations of the sternum representing anterior thorax loading contributed to bilateral fractures. Inward bending initiated by the distal femur complex resulting in adduction of ipsilateral lower extremity resulted in intertrochanteric fracture to the rear seat occupant. These results serve as a data set for evaluating the biofidelity of the WorldSID and federalized side impact dummies and assist in validating human body computational models, which are increasingly used in crashworthiness studies.     

新型纳米结构铈锰复合氧化物的磷吸附行为与机制研究

采用共沉淀法制备了一种新型铈锰复合氧化物吸附剂,对其进行了表征,并对磷吸附行为与机制进行了研究.表征结果分析表明,此氧化物由纳米级颗粒组成;铈锰复合氧化物中的铈氧化物有类似水合氧化铈的无定形结构;BET比表面积为157 m2·g-1,等电点为6.5.吸附实验结果表明,Langmuir吸附等温线模型可以更好地拟合铈锰复合氧化物对磷的吸附,最大吸附量为28.6 mg·g-1(p H=7.0);铈锰复合氧化物对磷具有较高的吸附速率,更符合准二级动力学模型;溶液p H对铈锰复合氧化物吸附磷的影响较为明显,随p H升高,吸附量降低;离子强度则影响不大;共存阴离子对吸附影响的大小顺序为Si O2-3CO2-3Cl-≥SO2-4.通过对铈锰复合氧化物吸附磷前后Zeta电位和红外谱图(FTIR)分析,可以推断磷在铈锰复合氧化物表面发生了特性吸附,磷酸根主要通过取代复合氧化物表面的金属羟基而被吸附去除.     

Effect of commercial pesticides on plant growth-promoting activities of Burkholderia sp. strain L2 isolated from rhizosphere of Lycopersicon esculentum cultivated in agricultural soil

The in vitro study was carried out to examine the toxicity of four commercially used pesticides (phorate, mancozeb, chlorpyrifos, and endosulfan) at the recommended dose (1X) and higher field doses (1.5X, 2X, 2.5X, and 3X) on plant growth-promoting activities of Burkholderia sp. strain L2, isolated from pesticide-treated rhizosphere of Lycopersicon esculentum. At the recommended dose, level of toxicity of all the pesticides to phosphate solubilization activity and indole-3-acetic acid (IAA) production was less detrimental as compared to exceeding doses. At maximum dose rate of each pesticide, the percentage decrease in phosphate solubilization and IAA production over control was found in order of chlorpyrifos < mancozeb < endosulfan < phorate. Present study proves that Burkholderia sp. strain L2 could be used as a potential microbial inoculant in the agricultural soil having persistent pesticide residues.