Thermal and mechanical properties of poly(lactic Acid) and poly(ethylene/butylene Succinate) blends

In this study, blends of poly (lactic acid) (PLA) with poly(ethylene/butylene succinate) (Bionolle) have been investigated for their thermal and mechanical properties as a function of the concentration of Bionolle. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and tensile tests were used to characterize the blends. From the results of the DMA and DSC, it was found that this blend system was not miscible within the compositions studied. DSC results showed that adding Bionolle aids in crystallization of PLA. It was observed that increasing the Bionolle concentration led to a slight increase in the strain-at-break of the blends but a decrease in the Young’s modulus and ultimate tensile strength. Biaxially oriented films showed an increase in tensile strength, modulus, and strain-at-break.     

刺激性气体HCl在不同尺度火灾实验中的释放行为

火灾是一种灾害性燃烧现象 ,给人员和财产安全带来极大损失。氯化氢 (HCl)是火灾烟气中阻碍人员逃生的最重要的刺激性气体之一。以典型的小尺度和大尺度实验为例 ,分析了加热程度和通风供氧对常用有机材料起火后释放HCl的影响 ,发现不论小尺度还是大尺度 ,HCl的形成只与燃烧过程有关 ,与氧化过程无关 ,HCl的生成率不随通风情况不同而改变。实验中影响HCl释放的主要因素是热 (辐射加热热流密度或温度 )。当超过CCl键发生断裂的温度后 ,继续升温HCl释放速率不发生改变 ,出现稳定释放阶段。在反映HCl释放过程不同尺度间存在共性 ,因此 ,利用小尺度的结果进行释放规律内在机理的探索是合理的方法     

Mechanical and Barrier Properties of Biodegradable Films Made from Chitosan and Poly (Lactic Acid) Blends

Biodegradable film blends of chitosan with poly(lactic acid) (PLA) were prepared by solution mixing and film casting. The main goal of these blends is to improve the water vapor barrier of chitosan by blending it with a hydrophobic biodegradable polymer from renewable resources. Mechanical properties of obtained films were assessed by tensile test. Thermal properties, water barrier properties, and water sensitivity were studied by differential scanning calorimeter analysis, water vapor permeability measurements, and surface-angle contact tests, respectively. The incorporation of PLA to chitosan improved the water barrier properties and decreased the water sensitivity of chitosan film. However, the tensile strength and elastic modulus of chitosan decreased with the addition of PLA. Mechanical and thermal properties revealed that chitosan and PLA blends are incompatible, consistent with the results of Fourier transform infrared (FTIR) analysis that showed the absence of specific interaction between chitosan and PLA.     

Lightweight Concrete Containing an Alkaline Resistant Starch-Based Aquagel

Starch aquagel-based lightweight concrete has properties similar to those of other lightweight concrete products. However, starch aquagels are unstable in the strongly alkaline conditions typical of Portland Cement-based concrete and may interfere with the setting process. The effect of alkali treatments on the physical, mechanical, and functional properties of starch aquagels and aquagels from starch/polymer blends was investigated. Starch was blended at 100–115°C in a twin-screw extruder with five different polymers to determine whether the blends improved alkaline resistance. Polymer blends containing 5%, 15%, and 30% of the polymer hydrated and formed aquagels when equilibrated in water for 24 h. However, equilibrium moisture content was lower for the blends compared to the starch control. Aquagels equilibrated in 0.15 N NaOH swelled, lost compressive strength and had greater than 90% moisture. The blend of starch and 30% PVOH absorbed less moisture and was more resistant to alkaline dissolution in 1 N NaOH than the other blends tested making it a more suitable material for aquagel-based concrete. The moisture content of starch-based aquagels and mixing time were critical factors in determining setting times. The size of aquagel blends had a minor effect on density and compressive strength.     

亚甲蓝湿式氧化影响因素研究

以湿式氧化技术对亚甲蓝水溶液进行处理,用水样COD去除率评价处理效果.考察了反应时间、温度、氧分压、搅拌速度、进水pH值以及进水浓度对处理效果的影响,并进行机理分析.实验确定的最佳操作工艺条件为:反应温度210℃、氧分压2.0 MPa、搅拌速度880 r/min、进水pH=11.30.在此条件下,COD为2 000mg/L的亚甲蓝水溶液,反应90min时COD去除率达93.2%.     

二安替比林甲烷分光光度法测定氯化镁中钛的含量

用盐酸溶解氯化镁样品,以抗坏血酸和焦磷酸钠共同作掩蔽剂,在酸性介质中用二安替比林甲烷分光光度法测定氯化镁中钛的含量,给出了合理的实验条件.     

基于改性凹凸棒土的强化混凝处理高藻低浊原水工艺

针对水厂低浊高藻水的处理难题,研究了改性凹凸棒土(改性凹土)联合聚合氯化铝(PAC)强化混凝的除藻除浊效果。设计实验原水条件为叶绿素a(chl-a)浓度为98.58~110.35μg/L,浊度(5.6±0.5)NTU。考察了PAC和改性凹土的复配投加量、混凝沉淀时间、pH、投加顺序、搅拌速率等工艺参数对Chl-a和浊度耦合去除效果的影响。结果表明,"PAC+改性凹土"对Chl-a和浊度的去除效果明显优于单投PAC的效果。当PAC投药量12 mg/L,改性凹土投药量10 mg/L,沉淀时间20 min时,对Chl-a和浊度的去除率可分别达到92.5%和89.2%,可至少减少40%的PAC投量,且形成的矾花密实,沉降速度快,去除效率高。最适pH范围为7~8。投加顺序应为先投加改性凹土,混合搅拌转数宜慢速,可控制为50 r/min。     

臭氧氧化法降解聚氯乙烯离心母液废水中3种有机物

以聚氯乙烯离心母液废水中含量较高的3种有机物(聚乙烯醇、异辛醇和α-甲基苯乙烯)作为目标物,考察臭氧氧化工艺对3种有机物的去除效果,同时考察反应时间、臭氧投加量和初始pH对处理效果的影响。实验结果表明,臭氧氧化处理3种废水的最佳反应时间和臭氧投加量分别为:聚乙烯醇25 min,136 mg/L;异辛醇60min,312 mg/L;α-甲基苯乙烯60 min,32 mg/L。在此条件下,3种有机物的去除率分别为98%、85%和95%。此外,碱性条件有助于臭氧氧化工艺对3种有机物的降解。产物分析结果表明,经臭氧氧化,聚乙烯醇断链后进一步反应生成了草酸单乙酯,异辛醇和α-甲基苯乙烯分别生成了和苯乙酮。     

二氧化钛脱除高温烟气中的氯化氢

HCl是城市垃圾焚烧产生的主要气体污染物之一。将一种新型脱氯剂TiO2引入到垃圾焚烧系统中,并与其他脱氯剂的性能进行比较。研究了不同脱氯剂使用量、不同反应温度和不同HCl气体浓度对TiO2、CaO和CaTiO3脱氯效果的影响。结果显示,TiO2能在高温(800~1 000℃)、高HCl浓度(1 303.6~1 629.5 mg/m3)下获得较好的脱氯效果。与传统的脱氯剂CaO相比,TiO2更适合于高温烟气脱氯,其在1 000℃时的氯容(36.3 mg HCl/g TiO2)几乎是相同情况下的CaO氯容(9.3 mg HCl/g CaO)的4倍。而CaTiO3的脱氯效果不但受到自身分解效率的影响,还受到TiO2和CaO脱氯效果的影响,其脱氯效果较差。     

膜电解技术处理含氯及重金属的废酸

采用离子交换膜电解技术处理铜冶炼过程产生的含氯及重金属的废酸。考察了废酸处理工艺、电解温度、电解时间、电流密度和催化剂的添加等条件对处理效果的影响。实验结果表明：采用先沉淀重金属后脱氯的废酸处理工艺，氯离子和铜离子的去除效果均较好;当以钛盐为催化剂时，在电解温度为40 ℃、电解时间为2.0 h、电流密度为825 A/m²的最佳工艺条件下，处理后废酸中的氯离子质量浓度为0.22 g/L，氯离子去除率为98.59%，铜离子质量浓度为0.45 g/L，铜离子去除率为95.08%，其他重金属大部分也得到有效去除。净化后的废酸可回用至铜冶炼的生产过程中。