Dissimilatory reduction of FeIII (EDTA) with microorganisms in the system of nitric oxide removal from the flue gas by metal chelate absorption

In the system of nitric oxide removal from the flue gas by metal chelate absorption, it is an obstacle that ferrous absorbents are easily oxidized by oxygen in the flue gas to ferric counterparts, which are not capable of binding NO. By adding iron metal or electrochemical method, Fe^Ⅲ (EDTA) can be reduced to Fe^Ⅱ(EDTA).However, there are various drawbacks associated with these techniques. The dissimilatory reduction of Fe^Ⅲ(EDTA) with microorganisms in the system of nitric oxide removal by metal chelate absorption was investigated. Ammonium salt instead of nitrate was used as the nitrogen source, as nitrates inhibited the reduction of Fe^Ⅲ due to the competition between the two electron acceptors. Supplemental glucose and lactate stimulated the formation of Fe^Ⅱ more than ethanol as the carbon sources. The microorganisms cultured at 50~C were not very sensitive to the other experimental temperature, the reduction percentage of Fe^Ⅲ varied little with the temperature range of 30-50℃.Concentrated Na2 CO3 solution was added to adjust the solution pH to an optimal pH range of 6-7. The overall results revealed that the dissimilatory ferric reducing microorganisms present in the mix-culture are probably neutrophilic, moderately thermophiUc Fe^Ⅲ reducers.     

菌-藻共生好氧颗粒污泥的稳定性机理

在非曝气条件下接种好氧颗粒污泥(AGS)和绿藻藻种,经过18d的培养,成功构建了菌-藻共生好氧颗粒污泥系统(ABGS).研究表明,在非曝气条件下,与传统的AGS相比,ABGS具有更高的生物活性、除污染效能和机械强度,说明ABGS的稳定性更优.对ABGS的稳定性机理进行分析,发现在颗粒化过程中,胞外聚合物(EPS)特别是...     

传统活性污泥法与膜生物反应器污泥沉降性能的比较

针对污泥沉降性能,在运行条件相同的情况下对膜生物反应器(MBR)与传统活性污泥法(CAS)进行比较。结果表明：CAS工艺污泥沉降性能优于MBR工艺;CAS工艺出水水质受污泥沉降性能影响大;MBR工艺污泥沉降性能主要由反应器中累积的高浓度胞外聚合物(EPS)含量所影响,当EPS浓度大于100mg／g时,污泥沉降性能开始恶化;CAS工艺曝气池中EPS浓度没有累积;MBR工艺污泥颗粒平均粒径小于CAS工艺中污泥颗粒。     

受四环素影响的活性污泥胞内外聚合物特征

利用离心加超声的方法对处理四环素抗生素废水的活性污泥胞外聚合物(EPS)和胞内聚合物(IPS)进行提取,将其分为-溶解型胞外聚合物(slime)、松散附着型胞外聚合物(LB)、紧密附着型胞外聚合物(TB)、胞内聚合物(IPS).用BCA法和蒽酮-硫酸法测定了各层EPS和IPS溶液中的蛋白质和多糖含量,同时用三维荧光光谱扫描(EEM)和同步荧光光谱扫描(SFS)对其中的溶解性有机物(DOM)进行定性和定量分析,结果表明在EPS中的蛋白质和多糖的含量高于IPS,且蛋白质含量均比多糖含量高,而在slime和IPS中的蛋白质和多糖的含量高于LB和TB;低激发波长类色氨酸和高激发波长类色氨酸是EPS和IPS溶液的主要成分,且溶液中的溶解性代谢产物和芳香蛋白类物质相对含量在slime、LB、TB和IPS逐渐增加,而难降解有机物-腐殖酸类物质的相对含量逐渐降低;进水四环素浓度与污泥各层EPS和IPS溶液中DOM也具有较好的相关性;三维荧光法检测溶液中的DOM与化学分析测试出的蛋白质含量具有较好的相关性.     

Effect of biocides on the precipitation of calcium fluoride in the presence of anionic copolymeric inhibitors

The inhibitory efficiency of anionic copolymers and the effect of the biocides sodium hypochlorite, glutaraldehyde, and tris(hydroxymethyl)nitromethane on the precipitation behavior of calcium fluoride (CaF₂) were studied. The efficiency of polymeric inhibitors was traced from conductivity measurements by using half-life (t_1/2) method. X-ray diffraction parameters have been measured for calcium fluoride scale minerals. An anionic copolymer (K-798) acts as one of the best inhibitors for the precipitation process of the calcium fluoride in water as compared to K-775. It is assigned to the fact that the copolymer (K-798) contains both sulfonic acid and sulfonated styrene groups while the polymer (K-775) having only the sulfonic acid group. It was further observed that the biocides have no appreciable effect on the performance of the anionic polymeric inhibitors.     

The prediction of adsorption isotherms of ester vapors on hypercrosslinked polymeric adsorbent

Adsorption isotherms of methyl acetate, ethyl acetate, propyl acetate, isopropyl acetate and ethyl propionate on hypercrosslinked polymeric resin (ND- 100) were measured at 303K, 318K and 333K,respectively, and well fitted by Dubinin–Astakhov (DA) equation. The plots of the adsorbed volume (q _v ) versus the adsorption potential (ε) at three different temperatures all fell basically onto one single curve for every ester. A predicted model based on DA equation was obtained on the basis of adsorption equilibrium data of methyl acetate, ethyl acetate and ethyl propionate at 318K. The model equation successfully predicted the adsorption isotherms of methyl acetate, ethyl acetate and ethyl propionate on ND-100 at 303K, and 333K, and also gave accurate predictive results for adsorption isotherms of the other two ester compounds (propyl acetate and isopropyl acetate) on ND-100 at 303K, 318K and 333K. The results proved the effectiveness of DA model for predicting the adsorption isotherms of ester compounds onto ND-100. In addition, the relationship between physico-chemical properties of adsorbates and their adsorption properties was also investigated. The results showed that molecular weight, molar volume and molar polarizability had good linear correlations with the parameter E (which represents adsorption characteristic energy) of DA equation.     

2-丁烯醛生产废水对厌氧生物处理的毒性

以厌氧颗粒污泥为受试生物、乙酸钠为底物,研究了2-丁烯醛废水的厌氧处理毒性及污泥胞外聚合物(EPS)的组成变化.结果表明,2-丁烯醛废水COD￡850mg/L时,厌氧颗粒污泥的比产甲烷活性(SMA)几乎不受影响;当废水COD从2125mg/L提高到4249mg/L时,厌氧颗粒污泥的比产甲烷活性(SMA)从70.5mLCH4/(gVSS·d)降低至9.4mLCH4/(gVSS·d);COD为8499mg/L时,厌氧颗粒污泥的SMA仅为4.7mLCH4/(gVSS·d),且废水中有毒物质表现为杀菌性毒素.随着COD升高,EPS(TOC表征)、多聚糖、蛋白质含量呈现先降低后升高趋势.三维荧光光谱结果显示,不同COD条件下EPS荧光峰数量及位置相同,分别为类酪氨酸荧光峰peak A (λex/λem=275nm/305nm)、类色氨酸荧光峰Peak B (λex/λem=275nm/350nm)、辅酶F420贡献的荧光峰Peak C (λex/λem=415nm/470nm)及类富里酸荧光峰Peak D (λex/λem=335nm/450nm),其中荧光峰peak A和peak B峰强度较强.     

不同EPS组成生物膜对Cu2+吸附的研究

采用自行设计的反应器,通过调节培养液的配比对载体进行挂膜,得到蛋白质和多糖含量比分别为7:1、5:1和10:1的3种生物膜作为吸附剂,用其对Cu2+进行吸附试验,同时对吸附机理进行探讨.结果表明,培养8d后,生物膜可挂膜成熟,在C/N=12时,生物膜上的菌落数较C/N=4和C/N=37条件下多.PN/PS值越小,生物膜对铜的吸附量越高,EPS3对Cu2+的吸附量分别高出EPS1 7.37 %, EPS2 7.62%.在生物膜吸附Cu2+后,溶液中Ca2+、Mg2+、K+含量明显升高,表明离子交换对生物膜吸附Cu2+起主要作用,且Cu2+更易与Ca2+和Mg2+产生离子交换作用.当KNO3浓度在0.1~0.6mol/L之间,随着离子强度的增加,生物膜吸附Cu2+的量迅速减少,当KNO3浓度大于0.6mol/L时,生物膜对Cu2+吸附量的变化趋于平缓,说明生物膜对Cu2+的吸附同时包括离子交换吸附和化学吸附.     

塑料管材输配水过程中有机物释放规律研究

研究了目前给水管网中常用的3种塑料管材,未增塑聚氯乙烯(uPVC),聚乙烯(PE)和无规共聚聚丙烯(PPR)管在输配水过程中有机物的释放规律.通过静态管段实验模拟给水管网中不同输配水状态,选取总有机碳(TOC)为综合评价指标,考察了不同塑料管材中有机物随时间的迁移释放特性,并分析了管材有机物释放对管网水中余氯消耗的影响.随着管材输配水次数的增加,uPVC管释放至水中的TOC浓度和TOC释放速率分别在0.03mg/L和0.04μg/(d?cm2)以下,而PE管和PPR管在输配水过程中TOC的释放浓度和释放速率在初期最大[PE: 0.19mg/L,0.25μg/(d?cm2);PPR:0.07mg/L,0.09μg/(d?cm2)],且后期递减并趋于平稳[PE:0.03~0.08mg/L,0.05~0.10μg/(d?cm2);PPR:0.01~0.03mg/L, 0.01~0.04μg/(d?cm2)].随着水力停留时间的增加,不同管材释放的有机物浓度持续升高.不同管材有机物的释放能力排序为:PE>PPR>uPVC.各管材的有机物释放特性直接影响管网水的余氯消耗特性,且管材的有机物释放量越多,管网水的余氯消耗越快.PE管的使用易引起水体有机污染问题.本研究明确了3种常用塑料管材的有机物释放规律,将进一步为与塑料管材安全性能评价相关的国家标准的修订提供理论依据.     

芬顿试剂氧化对污泥脱水性能的影响

利用芬顿试剂调理污泥,以W_C(污泥滤饼含水率)和CST(毛细吸水时间)作为评价污泥脱水性能的指标,通过分析污泥中各层ρ(EPS)(EPS为胞外聚合物)和上清液中小分子有机物质量浓度来阐明污泥脱水性能的变化. 结果表明:芬顿试剂调理可促进EPS氧化分解,TB-EPS(紧密结合的胞外聚合物)破解转化为LB-EPS(松散结合的胞外聚合物)和S-EPS(上清液层胞外聚合物),大幅降低W_C和CST. 试验中当pH为4,w(H₂O₂)和 w(Fe2+)均为40 mg/g时,ρ(EPS)降低了33.04%,W_C和CST分别降至63.36%和28.7 s. Pearson相关性分析表明,ρ(TB-EPS)与W_C和CST均存在显著的正相关性(P＜0.01),是影响污泥脱水性能的重要因素,而ρ(LB-EPS)和ρ(S-EPS)与污泥脱水性能的相关性较低. 液相色谱分析表明,随着芬顿试剂投加量的增大,EPS等有机物分解程度增大,污泥上清液中小分子有机物种类明显增多,其质量浓度显著升高,ρ(甲酸)和ρ(乙酸)分别由原污泥的52.72、15.99 mg/L升至446.05、522.36 mg/L.