Anti-fouling ultrafiltration membrane prepared from polysulfone-graft-methyl acrylate copolymers by UV-induced grafting method

Membrane fouling is one of the most important challenges faced in membrane ultrafiltration operations. The copolymers of polysulfone-graft-methyl acrylate were synthesized by homogeneous photo-initiated graft copolymerization. The variables affecting the degree of grafting, such as the time of UV(Ultraviolet-visible)irradiation and the concentrations of the methyl acrylate and photoinitiator, were investigated. The graft copolymer membranes were prepared by the phase inversion method. The chemical and morphological changes were characterized by attenuated total reflection-Fourier transform infrared spectroscopy(ATR/FT-IR), scanning electron microscopy, and water contact angles measurements. Results revealed that methyl acrylate groups were present on the membranes and the graft degree of methyl acrylate had remarkable effect on the performance of membranes. Pure water contact allgle on the membrane surface decreases with the increase of methyl acrylate graftdegree. which indicated that the hydrophilicity of graft copolymer membranes Was improved. The permeation fluxes of pure water and bovine serum albumin solution were measured to evaluate the antifouling property of graft copolymer membranes, the results of which have shown an enhancement of antifouling property for graft copoly mermembranes.     

刚果红分子印迹聚合物纳米微球的合成及吸附性能

本研究以刚果红为模板分子,α-甲基丙烯酸(MAA)为功能单体,二甲基丙烯酸乙二醇酯(EGDMA)为交联剂,乙腈为致孔剂,2,2-偶氮二异丁腈(AIBN)为引发剂,采用沉淀聚合法制备了刚果红分子印迹聚合物纳米微球(MIP).通过扫描、透射电镜对聚合物的结构和形貌进行了表征,结果显示制备的MIP微球的粒径在90 nm左右,粒径较为均匀.利用氮气吸附脱附实验测定了聚合物颗粒的比表面积和孔容.并对诸多吸附影响因素以及分子印迹聚合物的吸附能力、选择性和重复利用率进行了分析.结果表明,MIP对刚果红表现出较好的选择性识别能力,可多次循环使用,能用于染料废水中刚果红的选择性吸附.     

PVDF ultrafiltration membranes of controlled performance via blending PVDF-g-PEGMA copolymer synthesized under different reaction times

PVDF blended different graft ratio of PVDF-g-PEGMA were systematically studied. Tuning the amphiphilic copolymer synthesis time to control membrane performance. The PVDF membrane with PVDF-g-PEGMA at 19 h possesses most surface oxygen content. The synthesis time of PVDF-g-PEGMA at 9 h is good for high flux UF membrane. Polyvinylidene fluoride grafted with poly(ethylene glycol) methyl ether methacrylate (PVDF-g-PEGMA) was synthesized using atomic transfer radical polymerization (ATRP) at different reaction times (9 h, 19 h, and 29 h). The corresponding conversion rates were 10%, 20% and 30%, respectively. PVDF was blended with the copolymer mixture containing PVDF-g-PEGMA, solvent and residual PEGMA under different reaction times. In this study, we explored the effect of the copolymer mixture additives with different synthesis times on cast membrane performance. Increasing the reaction time of PVDF-g-PEGMA causes more PVDF-g-PEGMA and less residual PEGMA to be found in the casting solution. Incremental PVDF-g-PEGMA can dramatically increase the viscosity of the casting solution. An overly high viscosity led to a delayed phase inversion, thus hindering PEGMA segments in PVDF-g-PEGMA from migrating to the membrane surface. However, more residual PEGMA contributed to helping more PEGMA segments migrate to the membrane surface. The pure water fluxes of the blended membrane with reaction times of 9 h, 19 h, and 29 h are 5445 L·m⁻²·h⁻¹, 1068 L·m⁻²·h⁻¹and 1179 L·m⁻²·h⁻¹, respectively, at 0.07 MPa. Delayed phase inversion can form smaller surface pore size distributions, thus decreasing the water flux for the membranes with PVDF-g-PEGMA at 19 h and 29 h. Therefore, we can control the membrane pore size distribution by decreasing the reaction time of PVDF-g-PEGMA to obtain a better flux performance. The membrane with PVDF-g-PEGMA at 19 h exhibits the best foulant rejection and cleaning recovery due to its narrow pore size distribution and high surface oxygen content.     

用废聚对苯二甲酸乙二醇酯制备对苯型不饱和聚酯树脂

用废聚对苯二甲酸乙二醇酯(PET)制备对苯型不饱和聚酯树脂。考察了醇解时间对醇解产物、聚合温度对反应产物的影响。该方法的主要工艺参数为：废PET：PG(摩尔比)等于1：1．5,废PET：MA(摩尔比)等于1：1,醇解温度190～200℃,醇解时间3．5～4h,聚合温度190～210℃,聚合反应时间1．5～2h。试验所得对苯型不饱和聚酯树脂产品的性能符合企业通用型不饱和聚酯树脂的标准。     

反相乳液聚合制备阳离子聚丙烯酰胺及其絮凝性能评价

研究了单体浓度、单体配比、反应温度、引发剂用量等因素对所制备的阳离子聚丙烯酰胺特性粘度、转化率、阳离子度的影响,并对产品的污水絮凝性能进行了评价。较佳的制备条件为:单体浓度为45%,单体配比为7∶3,引发剂用量m(引发剂)/m(单体)为0.5%,引发温度为45℃。用红外光谱对共聚物进行了结构表征,结果表明聚合物中有六元氮杂环的存在,达到预定要求。对共聚物进行了油田污水絮凝性能评价,研究表明单独使用自制阳离子聚丙烯酰胺(CPAM)时浊度的去除率为86.22%,COD去除率为87.95%,与聚合氯化铝复配使用时浊度去除率提高到92.91%,COD去除率提高到92.68%。