生化法处理含氨废水动力学研究

对生化法处理含氨废水过去中有重要影响的动力学因素进行了试验研究和分析，得出了利用高效微生物菌群废水中COD和NH3－N的动力学条件，温度为20－35℃，PH为7－8，DO大于2.6mg/L,MLSS大于2.6g/L，C／N小于3。在此条件下处理含氨废水，处理后的出水达到国家化肥行业一级排放标准。     

利用缫丝废水处理过程中产生的微生物蛋白制备复合氨基酸

以缫丝废水处理过程中产生的微生物蛋白为原料,采用正交实验分析了采用酸水解、超声波水解、微波水解制备复合氨基酸的最佳工艺条件,并对比了最佳工艺条件下的水解效果.结果表明,酸水解的最佳工艺条件是水解时间2.Oh、固液比(体积比,下同)5∶1、硫酸质量分数50％、水解温度100℃,超声波水解的最佳工艺条件是水解时间0.5h、...     

Treatment of coking wastewater by an advanced Fenton oxidation process using iron powder and hydrogen peroxide

In this study the treatment of coking wastewater was investigated by an advanced Fenton oxidation process using iron powder and hydrogen peroxide. Particular attention was paid to the effect of initial pH, dosage of H₂O₂ and to improvement in biodegradation. The results showed that higher COD and total phenol removal rates were achieved with a decrease in initial pH and an increase in H₂O₂ dosage. At an initial pH of less than 6.5 and H₂O₂ concentration of 0.3 M, COD removal reached 44-50% and approximately 95% of total phenol removal was achieved at a reaction time of 1 h. The oxygen uptake rate of the effluent measured at a reaction time of 1 h increased by approximately 65% compared to that of the raw coking wastewater. This indicated that biodegradation of the coking wastewater was significantly improved. Several organic compounds, including bifuran, quinoline, resorcinol and benzofuranol were removed completely as determined by GC-MS analysis. The advanced Fenton oxidation process is an effective pretreatment method for the removal of organic pollutants from coking wastewater. This process increases biodegradation, and may be combined with a classical biological process to achieve effluent of high quality.     

Recovery of Ni(II) from real electroplating wastewater using fixed-bed resin adsorption and subsequent electrodeposition

Resin adsorption and subsequent electrodeposition were used for nickel recovery. Treated wastewater can meet the Electroplating Pollutant Discharge Standard. The spent resin is completely regenerated by 3 BV of 4% HCl solution. 95.6% of nickel in concentrated eluent was recovered by electrodeposition. Effective recovery of high-value heavy metals from electroplating wastewater is of great significance, but recovering nickel ions from real electroplating wastewater as nickel sheet has not been reported. In this study, the pilot-scale fixed-bed resin adsorption was conducted to recover Ni(II) ions from real nickel plating wastewater, and then the concentrated Ni(II) ions in the regenerated solution were reduced to nickel sheet via electrodeposition. A commercial cation-exchange resin was selected and the optimal resin adsorption and regeneration conditions were investigated. The resin exhibited an adsorption capacity of 63 mg/g for Ni(II) ions, and the average amount of treated water was 84.6 bed volumes (BV) in the pilot-scale experiments. After the adsorption by two ion-exchange resin columns in series and one chelating resin column, the concentrations of Ni(II) in the treated wastewater were below 0.1 mg/L. After the regeneration of the spent resin using 3 BV of 4% (w/w) HCl solution, 1.5 BV of concentrated neutral nickel solution (>30 g/L) was obtained and used in the subsequent electrodeposition process. Using the aeration method, alkali and water required in resin activation process were greatly reduced to 2 BV and 3 BV, respectively. Under the optimal electrodeposition conditions, 95.6% of Ni(II) in desorption eluent could be recovered as the elemental nickel on the cathode. The total treatment cost for the resin adsorption and regeneration as well as the electrodeposition was calculated.     

重铬酸钾法测定炼油废水COD的适用性分析

为了分析0.250 mol/L与0.025 mol/L重铬酸钾法测定炼油催化剂行业高氯废水COD的适用性,进行了比对实验。结果表明：两者测定结果相差60.5～76.8 mg/L;高浓度重铬酸钾法精密性较好, RSD%≤4.8%,准确度较高,与氯气校正法测定结果基本吻合,相对误差≤6%;低浓度的重铬酸钾法精密性相对较差, RSD%≥8.1%,与氯气校正法测定结果相对误差大于40%,准确度低。在控制稀释水样Cl-浓度500～800 mg/L范围时,采用重铬酸钾法测定COD,适宜于高浓度的方法。     

AF+BAF深度处理PCB生产废水的试验研究

针对PCB废水难降解及含重金属铜的特点,在经过一系列的物化处理的基础上,采用AF+BAF组合工艺对其进行深度处理。试验研究中,通过控制污水在反应器中的停留时间,使得废水在AF中水解酸化,以增加废水的可生化性,在此基础上利用BAF的生物膜来去除污水中剩余的有机物。试验结果表明,试验系统对PCB废水中的COD、Cu2+去除效果良好,出水COD、Cu2+的含量分别稳定在10~50mg/L和0.02~0.1mg/L,达到排放标准。     

Fenton试剂处理酸性染料废水的研究

采用Ｆｅｎｔｏｎ试剂处理酸性染料废水，在ｐＨ＝３，〔ＦｅＳＯ４〕＝４０ｍｇ／Ｌ，〔Ｈ２Ｏ２〕＝８００ｍｇ／Ｌ时，酸性媒介漂蓝废水的色度及ＣＯＤ去除率分别达９８．６％和８０．１％。     

射流曝气MBR处理啤酒废水的试验

射流曝气提高了系统的氧利用效率及传质效率.通过逐渐提高进水的容积负荷来考察系统的处理效果, 试验表明, 利用射流曝气MBR处理模拟啤酒废水是可行的, 系统对COD、氨氮、浊度平均去除率为95.74%,97.84%,99.5%.由于系统运行期间不排泥, 因此系统对P O43-的去除效果不佳, 平均去除率为42.9%.膜对...     

污水除磷技术的研究与进展

详细介绍了污水除磷的迫切性及传统的污水除磷工艺原理与特点，阐述了污水除磷技术的最新发展动向。     

SPM对铅溶液的处理效果研究

含铅废水仅经过化学沉淀法处理后的出水不够稳定,因此需要后期处理来保证出水稳定并符合国家综合污水排放标准。新型特种粉体材料Special Powder Materia(lSPM)为我国自主研发的新型粉体材料,对微污染的水源有良好的处理效果,去除重金属的主要机理为电化学反应、吸附等。文章目的在于研究SPM去除铅效果的影响因素;研究SPM处理含铅溶液的浓度范围,考察将SPM的应用范围扩展至含铅废水后期处理的可行性。影响SPM处理效果的因素有进水流向、流量、填料高度、停留时间、含铅溶液浓度等,为了定量研究各个因素对SPM处理效果的贡献大小,文章采用配水试验,考察不同条件下SPM对铅的去除效率并进行正交分析。结果表明,进水方向采用逆流方向优于顺流方向,影响SPM处理铅溶液效率的主要因素为进水流量和进水浓度,SPM对较高浓度含铅溶液有明显的除铅效果,有望用于废水后期处理。进水方向为逆流,流量为12L/h,进水浓度为2mg/L时,出水浓度能长时间保证在1mg/L以下,符合国家综合污水排放标准。