固硫灰渣深度处理焦化废水的实验研究

选用同硫灰渣深度处理经生化处理后焦化废水,采用分光光度计法评价焦化废水的处理效果,采用XRD、XRF、SEM和IR等分析材料的成分、结构和微观形貌等.结果表明,固硫灰渣用量60 g/L、吸附时间15 min,焦化废水的脱色率可达94.22%,COD从原水的76.01 mg/L降低到处理后的5.76 mg/L,NH+4-...     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

煤的低温氧化实验研究及红外光谱分析

对不同温度下的氧化煤样通过红外光谱分析其微观结构及特征,得到煤样在不同低温氧化阶段的基团变化,从微观角度掌握煤样氧化过程的变化规律.通过对唐口煤矿1302工作面煤样的低温氧化和红外光谱分析,得到唐口煤矿煤样在低温氧化阶段的自燃倾向性和氧化过程中微观结构的变化规律,该成果为制定矿井内火灾的防治技术提供了科学依据.     

Study of Trace Elements and Soot in Aerosols from a Coal-Fired Power Plant in Northern Vietnam

Two measurement campaigns were conducted in two sampling sites, An Thinh and Duy Minh, in northern Vietnam during the months of November–December 2000 and November 2001–February 2002 in order to investigate the extend of the particulate air pollution from the Pha Lai coal fired power plant. Fine particle samples were analyzed by Energy Dispersive X-Ray Fluorescence spectrometry and soot samples were analyzed by reflectometer. The result showed that high concentration of soot and elements mostly coincided with the air masses originating from the power plant. Sea spray aerosol was found to be the major source of chlorine at both sites. Ratios of specific elements and principal component analysis (PCA) revealed that coal combustion was the main contributor to the air pollution at both sites. PCA also indicated that there were other sources responsible for the elements emission, probably the influence of long distance transport and Asian Brown Cloud.     

铁及铁铜氧化物对臭氧氧化酸性红B的催化效能

采用自蔓延溶胶凝胶法分别制备了铁氧化物和铁铜复合氧化物催化剂,以酸性红B为降解对象,对比了单独臭氧氧化、铁氧化物和铁铜复合氧化物催化臭氧氧化对酸性红B的降解效果,考察了磁力搅拌速度(500～1 640 r/min)、溶液pH(3～11)、臭氧投加速率(3.55～28.4 mg/min)对铁铜复合氧化物催化性能的影响。结果表明,与单独臭氧氧化比较,铁氧化物和铁铜复合氧化物均能加速酸性红B的降解,促进色度和COD的去除,结合催化剂的表征结果,推断催化剂表面羟基促进臭氧分解产生.OH是其氧化性能较好的主要原因,另外,催化剂的吸附能力对催化性能也有一定影响。随着磁力搅拌速度、溶液pH、臭氧投加速率的增大,铁铜复合氧化物催化臭氧氧化酸性红B的效果越好。     

垃圾炉一次风量对炉床燃烧影响的仿真研究

针对垃圾焚烧炉床层内垃圾燃烧过程复杂性及影响垃圾燃烧效率因素多的问题,运用数值仿真方法对某垃圾焚烧炉床层垃圾燃烧进行了模拟,获得了垃圾质量流失速率、水分蒸发速率、挥发分释放速率、焦炭燃烧速率和烟气的温度;并在50~1 000 Nm3/min范围内改变一次风流量,获得了床层质量流失比值、过剩空气系数和烟气中各组分的质量百分比含量。仿真结果显示,一次风流量取值517.47~6`32.09 Nm3/min时燃烧效率较高;炉排两端区域的一次风流量在50~75 Nm3/min时,可以使垃圾床表面平均温度明显提高,而且还可以提高燃烧效率,同时减少供风总量,节约能源与动力资源。本研究对优化设计垃圾焚烧炉,提高床层内垃圾的燃烧效率有一定参考价值。     

甲烷-煤尘复合火焰的传播与温度特征

为了揭示甲烷-煤尘复合体系的燃烧特征,利用高速摄像机、超细热电偶、显微镜头等对管道内甲烷-煤尘复合火焰的传播过程及其温度特征进行了试验研究.结果表明,随着煤尘浓度的增加,甲烷-煤尘复合火焰的最高温度及传播速度呈现先增大后减小的趋势; 对于甲烷-煤尘复合火焰,粒径较大的煤尘在较小的浓度达到最高温度,而粒径较小的煤尘则需要在较大的浓度达到最高温度.     

煤矸石自燃过程中多环芳烃含量的变化研究

采用室内模拟实验的方法,综合分析了煤矸石堆积自燃过程中多环芳烃(PAHs)含量的变化规律。研究发现,煤矸石自燃过程中,PAHs的生成与散失同时存在。较低的温度(60℃)对多环芳烃的生成具有一定的促进作用;500℃之后,PAHs全部散失或者降解为小分子物质,含量几乎为0。单个PAH的含量变化与总含量基本一致,仅是某一个PAH在不同温度下在总含量中所占的比例不同。自燃过程中高环的PAHs可能生成低环的PAHs使其含量增加。     

储罐硫腐蚀产物标志性气体的监测

含硫油品储罐内的腐蚀产物与油品中的活性硫反应生成硫化物,而此类硫腐蚀产物氧化自燃是导致储油罐发生火灾、爆炸事故的重要原因.通过试验考察了氧气体积比对硫腐蚀产物氧化自燃过程的影响,探索了铁锈模拟物在氧化过程中SO2气体的释放规律.结果表明:氧气浓度越高,硫腐蚀产物的自燃危险性越大;随着O2浓度增加,氧化反应中SO2的浓度越大,SO2气体析出速度越快,当氧化反应的温度为40℃时,SO2气体浓度达到最大.     

典型可燃物燃烧烟尘物化特性差异性研究

开展对典型可燃物燃烧烟尘的物化特性差异性研究,是全面了解烟尘信息的基础.基于可控条件下的燃烧试验,对典型可燃物燃烧烟尘物理特性和化学组分进行了分析.通过对比分析汽油燃烧烟尘、聚苯乙烯燃烧烟尘、ABS燃烧烟尘及柴油烟尘和正庚烷烟尘的透射电镜图片,对透射电镜图的紧凑性、复杂性及灰度值进行了深入分析,探讨了燃烧烟尘的物理差异性.利用固相微萃取-气质联用技术(SPME-GC-MS),对汽油燃烧烟尘、聚苯乙烯燃烧烟尘、ABS燃烧烟尘化学组分进行了分析和对比.通过燃烧烟尘的特征物质组分的分析,得到3种燃烧烟尘在特征物质的分布和出峰时间等方面的差异性.这些差异性可作为对烟尘来源及燃烧条件等因素判别的依据.