污泥生物处理的研究与应用

污泥生物处理技术包括污泥前置及后置的处理。污泥前置处理可以通过微生物自身的新陈代谢和微生物种群之间捕食作用,以及对工艺和反应器的改良来实现污泥减量。污泥后置生物处理是指污泥消化,可以使用高温-中温共相厌氧消化和蛋形污泥消化器对污泥进行减量;这些方法从不同侧面反应了目前污泥生物处理研究现状以及最新进展。     

AF+BAF深度处理PCB生产废水的试验研究

针对PCB废水难降解及含重金属铜的特点,在经过一系列的物化处理的基础上,采用AF+BAF组合工艺对其进行深度处理。试验研究中,通过控制污水在反应器中的停留时间,使得废水在AF中水解酸化,以增加废水的可生化性,在此基础上利用BAF的生物膜来去除污水中剩余的有机物。试验结果表明,试验系统对PCB废水中的COD、Cu2+去除效果良好,出水COD、Cu2+的含量分别稳定在10~50mg/L和0.02~0.1mg/L,达到排放标准。     

镧、铈对厌氧颗粒污泥产甲烷的Hormesis效应及其动力学研究

间歇培养条件下研究了单一稀土元素镧(La3 )和铈(Ce3 )在不同浓度水平下对厌氧颗粒污泥活性及其动力学行为的影响.结果表明,La3 和Ce3 对厌氧颗粒污泥比产甲烷活性有促进作用的浓度范围均为0.01～0.1 mg·L-1,促进作用浓度峰值均为0.05mg·L-1,最大促进百分比分别为10.35%和20.79%;La3 和Ce3 对SMA(比甲烷活性)的半抑制浓度分别为5mg·L-1和1000mg·L-1,La3 较易对污泥产生抑制作用.米-门方程可以用来描述厌氧消化过程中甲烷发酵阶段的动力学行为,稀土元素La3 和Ce3 投加至反应系统后,提高了甲烷发酵过程的动力学常数Vmax和半饱和常数Ks.     

气浮--厌氧--生物接触氧化工艺处理屠宰废水

介绍了采用气浮-厌氧-生物接触氧化工艺处理屠宰废水的工程实例。当进水CODcr≤4500mg／L时，出水可达到国家《肉类加工工业污染物排放标准》(GB13457—1992)一级标准。     

Effect of Cross-Linking Waste Protein with Dialdehydes on Its Biodegradation Under Anaerobic Conditions

Most native polymers used in processing and application technologies are admittedly disposable from the environment in a biologic manner, but products possess low mechanical strength. One of the paths to increasing this attribute (if feasible) is their cross-linking, which may, however, affect their readiness to biodegradation. In the presented work this condition was observed on the example of waste protein (Hykol B) cross-linking by means of glutardialdehyde and glyoxal. Degree and course of cross-linking were determined through impedance spectroscopy. The objective of this work also was to obtain data for constructing a sensor capable of following the cross-linking course in real time, for potential industrial application of Hykol in continuous production. Impedance spectroscopy proved to be applicable even to this kind of material marked by considerable water content and exhibiting relatively high electric conductivity; so far it had been used only for materials of low conductivity. An aqueous environment inoculated with digested anaerobic sludge from a municipal wastewater treatment plant was selected for modeling anaerobic conditions. The relation was studied between cross-linking degree given by content of cross-linking agent (determined by impedance spectroscopy) and biodegradation degree under anaerobic conditions. It was confirmed that network density as given by quantity of added agent not only reduced breakdown degree but also slowed the course of the process. This fact is particularly obvious with cross-linking by means of glyoxal; network density is thus dependent on type of employed substance, which affect type and structure of created network. That not merely forms an obstacle during polymer swelling and dissolution but also prevents access of bacteria to source of metabolized organic carbon.     

抽出式通风煤巷掘进过程中粉尘浓度分布规律的数值模拟

根据气固两相流理论，针对矿井掘进工作面的特点，采用计算流体力学的离散相模型（DPM）对掘进工作面通风过程中粉尘浓度进行数值模拟，总结抽出式通风掘进巷道中粉尘浓度的沿程分布及变化规律。     

特种胶塑复合管抗张强度计算

通过对特种胶塑复合管的抗张强度计算和生产实践，证明了矿用充填管路采用胶塑复合管是可行的。为矿用充填管以胶塑复合管替代铁管提供了依据。     

稠油污水生化性处理技术研究

为了探讨稠油污水能否使用生物法处理,以生活污水和农药厂生化池原菌种经过诱导驯化,分别培养了可以在稠油污水中生长的好氧菌种革兰氏阴性菌G-1和厌氧菌种革兰氏阴性菌G-2.以G-2和G-1对稠油污水进行顺序处理,可使其BOD5/CODCr达到0.26;采用SBR法对新疆稠油污水放大处理试验的结果：COD降至150 mg/L以下,各项指标达到GB8978-1998二级排放标准.     

利用白云石石灰去除与回收污泥厌氧消化液中氮和磷

以白云石石灰为实验材料去除与回收污泥厌氧消化液中的氮磷,通过小试实验研究不同投药固液比S/L、初始pH值、反应温度、搅拌速度及反应时间对去除与回收氮磷效果的影响。实验结果表明,在最佳投药固液比S/L为300mg/L,最佳初始pH值范围为8.5~9.5,反应温度为25.0℃,搅拌速度为150 r/min,反应时间为24 h条件下,氨氮(NH+4-N)和磷(PO3-4-P)的去除率分别为37.26%和89.60%。利用X射线衍射仪(XRD)、扫描电镜(SEM)对沉淀产物进行了表征,通过分析可知沉淀产物中含有磷酸铵镁(MAP),可实现废水中氮磷经济有效的回收。     

Highly efficient conversion of sugarcane bagasse pretreated with liquid hot water into ethanol at high solid loading

Liquid hot water (LHW), an environmental-friendly physico-chemical treatment, was applied to pretreat the sugarcane bagasse (SCB). Tween80, a non-ionic surfactant, was used to enhance the enzymatic hydrolysis of the pretreated SCB. It found that 0.125 mL Tween80 /g dry matter could make the maximum increase (33.2%) of the glycan conversion of the LHW-pretreated SCB. A self-designed laboratory facility with a plate-and-frame impeller was applied to conduct batch hydrolysis, fed-batch hydrolysis, and the process of high-temperature (50°C) fed-batch hydrolysis following low-temperature (30°C) simultaneous saccharification and fermentation (SSF) which was adopted to overcome the incompatible optimum temperature of saccharification and fermentation in the SSF process. After hydrolyzing LHW-pretreated SCB for 120 h with commercial cellulase, the total sugar concentration and glycan conversion obtained from fed-batch hydrolysis were 91.6 g/L and 68.3%, respectively, which were 9.7 g/L and 7.3% higher than those obtained from batch hydrolysis. With Saccharomyces cerevisiae Y2034 fermenting under the non-sterile condition, the ethanol production and theoretical yield obtained from the process of SSF after fed-batch hydrolysis were 55.4 g/L and 88.3% for 72h, respectively, which were 15.5 g/L and 24.7% higher than those from separate fed-batch hydrolysis and fermentation. The result of this work was superior to the reported results obtained from the LHW-pretreated SCB.