绿灯倒计时信号对驾驶行为的影响

为揭示绿灯倒计时信号对交叉口交通安全的影响,针对不同交通负荷与信号控制方式下的驾驶行为开展研究。选择大连市内的倒计时信号交叉口与非倒计时信号交叉口各2处,开展车辆行驶速度及不良驾驶行为调查。用数理统计方法,对比分析2类交叉口在平峰与高峰时段的车辆行驶速度特性,同时对比分析上述不同条件下闯黄灯及违规变道行为的发生数量。研究表明,绿灯倒计时信号在绿灯时间末期,会诱发一部分驾驶员加速行驶通过交叉口;绿灯倒计时信号在平峰时段对闯黄灯行为数量的影响较小,而对违规变道行为的数量有显著影响。     

BiOCl/TiO_2复合材料的可见光活性及机理研究

采用水热法和溶胶凝胶法制备新型BiOCl/TiO2复合材料并明确了最优的掺杂比例(2%).随后利用X射线衍射(XRD)、紫外可见漫反射(DRS)、透射电镜(TEM)和X射线光电子能谱(XPS)对该材料进行表征.由于禁带宽度较大,纯BiOCl和TiO2的可见光催化性能极差,然而二者复合后,同条件下的苯降解率却大幅提升,可以达到40%以上.经证实,催化剂制备过程中,Bi的状态发生变化,在TiO2导、价带之间插入新的能级,使其禁带宽度变窄,电子可以实现可见光跃迁.     

Synthesis, crystal structure, photodegradation kinetics and photocatalytic activity of novel photocatalyst ZnBiYO4

ZnBiYO₄ was synthesized by a solid-state reaction method for the first time. The structural and photocatalytic properties of ZnBiYO₄ were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV-Vis diffuse reflectance. ZnBiYO₄ crystallized with a tetragonal spinel structure with space group I41/A. The lattice parameters for ZnBiYO₄ were a = b = 11.176479 Å and c= 10.014323 Å. The band gap of ZnBiYO₄ was estimated to be 1.58 eV. The photocatalytic activity of ZnBiYO₄ was assessed by photodegradation of methyl orange under visible light irradiation. The results showed that ZnBiYO₄ had higher catalytic activity compared with N-doped TiO₂ under the same experimental conditions using visible light irradiation. The photocatalytic degradation of methyl orange with ZnBiYO₄ or N-doped TiO₂ as catalyst followed first-order reaction kinetics, and the first-order rate constant was 0.01575 and 0.00416 min^-1 for ZnBiYO₄ and N-doped TiO₂, respectively. After visible light irradiation for 220 min with ZnBiYO₄ as catalyst, complete removal and mineralization of methyl orange were observed. The reduction of total organic carbon, formation of inorganic products, SO₄^2- and NO₃^-, and evolution of CO₂ revealed the continuous mineralization of methyl orange during the photocatalytic process. The intermediate products were identified using liquid chromatography- mass spectrometry. The ZnBiYO₄/(visible light) photocatalysis system was found to be suitable for textile industry wastewater treatment and could be used to solve other environmental chemical pollution problems.     

Ecotect在建筑玻璃幕墙光反射影响评价中的应用研究

将Ecotect软件应用到建筑玻璃幕墙光反射影响评价中,应用结果表明,Ecotect软件能准确地确定建筑玻璃幕墙反射光的影响范围,且能准确地确定幕墙遮阳设施或周围建筑的遮挡效果,这可大大加强建筑玻璃幕墙光反射影响评价的准确性.另外,Ecotect软件还可准确地分析出受影响的敏感目标或敏感目标受照反射光的来源,这可使幕墙设计者有针对性对受影响敏感目标或对敏感目标产生反射光影响的建筑玻璃幕墙立面采取预防控制措施,来降低或者消除光反射,从而从源头上减少或消除幕墙反射光对周围环境敏感目标的影响.     

蒙脱土原位生长MoS2复合材料光催化降解罗丹明B的机理研究

通过在Na⁺-MMT表面生长MoS₂来提高窄带隙半导体光生电子分离速率及稳定性.利用阳离子填充法及水热法成功制备了复合光催化剂Na⁺-MMT/MoS₂,并通过FT-IR、SEM、TEM、Raman、XRD、TG、XPS、UV-DRS和ESR等表征进一步证明了材料的成功负载及光、电化学性能. 同时,以有机染料罗丹明B为待降解染料来评价光催化剂的催化性能,发现其在80 min可有效降解罗丹明B,降解率达96%.经过5次循环使用后,Na⁺-MMT/MoS₂复合光催化剂仍具有较好的光催化性能.因此,利用MMT的表面电负性及稳定的片层结构负载MoS₂,可形成光生电子迁移通道进一步提高电荷迁移速率及光催化剂的稳定性.本研究可为黏土材料调控窄带隙半导体制备环境友好型光催化剂提供新思路.     

地壳元素铁的吸光贡献对黑碳吸光增强估算的影响——以武汉为例

传统方法使用固定的波长吸收指数来估算地壳元素或棕碳吸光,但该方法只能处理仅存在两种组分的情形(黑碳/棕碳,或黑碳/地壳元素)的吸光贡献,存在较大不确定性.为此,本文提出一种新的方法,利用武汉在线观测数据(2021年2、3、8、9月),采用铁作为地壳元素的示踪物,利用最小相关系数法(MRS)得出地壳元素的吸光贡献,在扣除地壳元素吸光之后,再得到黑碳吸光增强系数(E_abs).结果显示观测期间370nm波段地壳元素吸光贡献均值为12.3%,月均值范围5.7%~15.5%,且波长吸收指数与铁的浓度正相关,表明地壳元素吸光贡献不可忽视.地壳元素吸光贡献呈现出显著的季节特征,呈现出冬季低,春季高的特点.地壳元素吸光的分离前后计算的E_abs存在一定的差异,受到了黑碳和铁的相关性的影响.观测期间扣除地壳元素吸光后,E_abs均值为1.43±0.53,在季节性上呈现春夏高,秋冬低的特性,春季较高E_abs值与春季黑碳较高的老化程度有关.E_abs对无机盐和有机物的含量存在正的依赖关系,证明了这些包裹物质对吸光增强的影响.     

外绝缘用液体硅橡胶的自然老化因素研究

近年来,液体硅橡胶(Liquid Silicone Rubber,LSR)已经在外绝缘领域得到了较为广泛的应用,但是目前对其耐老化性能的研究还不够深入。尤其是在中国南方地区使用时,高温、高湿环境更容易导致液体硅橡胶的老化。在许多地区都观察到了电流、电压互感器的液体硅橡胶绝缘外套的龟裂、老化现象,对设备的安全运行产生了影响。本文设计并实施了在光照、高温、高湿、电晕等老化因素作用下的液体硅橡胶人工老化试验,并对老化试验后的样品进行了硬度、力学性能、憎水性、光泽度以及SEM、FTIR等微观性能试验和分析。认为在光照作用下,高温、高湿环境对液体硅橡胶具有加速老化作用,表现为硬度上升、憎水性下降、光泽度下降,并且在表面出现细微裂纹。     

对定标用标准紫外辐射光源性能指标的探讨

紫外辐射是模拟环境条件测试的重要组成部分,对紫外辐射强度、剂量等的定标对于老化耐久实验数据的准确性和可靠性具有重要意义。本文通过实验手段对目前常见的定标用紫外标准光源的技术指标进行分析,同时对该类光源的性能指标未来的改进方向进行探讨,并提出了改进设计方案。     

用碳化法从制碱废渣一次盐泥中制取轻质氧化镁的研究

本研究是用制碱废渣一次盐泥作原料，采用二氧化碳碳化法制取轻质氧化镁。同时分析了提取轻质氧化镁后的残渣用于制造水泥或其它胶凝材料的原料的可行性。     

Determination of ammonium on an integrated microchip with LED-induced fluorescence detection

A simply fabricated microfluidic device integrated with a fluorescence detection system has been developed for on-line determination of ammonium in aqueous samples. A 365-nm light-emitting diode (LED) as an excitation source and a minor band pass filter were mounted into a polydimethylsiloxane (PDMS)-based microchip for the purpose of miniaturization of the entire analytical system. The ammonium sample reacted with o-phthaldialdehyde (OPA) on-chip with sodium sulfite as reducing reagent to produce a fluorescent isoindole derivative, which can emit fluorescence signal at about 425 nm when excited at 365 nm. Effects of pH, flow rate of solutions, concentrations of OPA-reagent, phosphate and sulfite salt were investigated. The calibration curve of ammonium in the range of 0.018-1.8 μupg/mL showed a good linear relationship with R² = 0.9985, and the detection limit was (S/N = 3) 3.6 × 10^-4 μupg/mL. The relative standard deviation was 2.8% (n = 11) by calculating at 0.18 μupg/mL ammonium for repeated detection. The system was applied to determine the ammonium concentration in rain and river waters, even extent to other analytes fluorescence detection by the presented device.