TiO2/PS/Fe3O4 光催化剂的低温制备及其光催化和磁回收性能

以聚苯乙烯(PS)包覆油酸修饰过的纳米Fe3O4为磁核,在低温(90℃)、中性(pH=7左右)条件下,制备了以PS为惰性隔离层的磁载TiO2光催化剂.用X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)对催化剂的物相组成、形貌、表面性质、磁学性质进行了表征.以苯酚为模拟污染物,考察了其光催化活性,以自制的磁回收装置,考察其回收特性.结果表明,低温制备的TiO2为锐钛矿结构,平均粒径为2～5 nm,催化剂TiO2/PS/Fe3O4[其中物质的量比为n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]具有结构完整的壳/壳/核结构,TiO2在PS/Fe3O4表面负载牢固;光催化降解苯酚遵循一级反应动力学方程,TiO2/PS/Fe3O4[n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]的反应速率常数K=0.025 8,与纯TiO2的活性接近(K=0.026 2);循环使用5次后,反应速率常数仅降低0.003 4.所制催化剂具有较强的磁感应强度,平均回收率可达到92%以上.该低温水解法制备的磁载TiO2光催化剂具有良好的应用前景.     

氮氟掺杂二氧化钛(N,F-TiO2)的制备及可见光催化活性的研究

以氨水为氮源,氢氟酸为氟源,采用溶胶-凝胶法制备了氮氟掺杂二氧化钛(N,F-TiO2)光催化剂,并通过X-射线衍射(XRD)和扫描电镜(SEM)技术对其晶型和形态进行表征.最后以酸性红B为模型污染物,探讨了N和F加入量、焙烧温度、焙烧时间、照射时间、催化剂用量、溶液初始浓度和照射功率等因素对N,F-TiO2可见光催化活性的影响.结果表明,制备的N,F-TiO2以锐钛型为主,N和F的掺杂对TiO2的晶相没有明显改变,但可以扩大TiO2的可见光响应范围.当N和F的加入量均为2.0%,且在500℃下焙烧40 min时,得到的N,F-TiO2的可见光催化活性明显高于单N或单F掺杂的TiO2(N-TiO2或F-TiO2).对于50 mL浓度为10.0 mg·L-1的酸性红B溶液,当催化剂加入量为1.5 g·L-1,128W光照3.0 h,溶液pH=5.6时,去除率为85.40%.适当延长光照时间至4.0 h,降解率几乎可达100%.另外,研究还证明了N,F-TiO2催化可见光降解过程中有.OH自由基生成.     

二氧化钛复合型催化剂制备及其微波辅助催化氧化甲苯性能

实验采用溶胶凝胶法和传统浸渍法制备了TiO2-分子筛复合载体及复合载体负载过渡金属与稀土元素催化剂,通过微波辅助催化氧化甲苯的性能实验考察其催化活性.结果表明,复合TiO2明显提高了载体结构的稳定性与耐温性,并使过渡金属铜(Cu)、锰(Mn)和稀土元素铈(Ce)等活性组分在催化剂表面的分散更均匀;在复合载体吸附、吸波性能与多相活性组分催化的共同作用下,Cu-Mn-Ce/TiO2-分子筛催化剂微波辅助催化氧化甲苯的完全燃烧温度仅为175℃,此时甲苯去除率可达99％;15 h的连续性实验表明,TiO2复合型催化剂具有良好的催化活性与稳定性.由催化剂表征分析结果可知,活性组分颗粒的均匀分布与铜、锰氧化物及铜锰尖晶石固溶物等活性相的存在促进了甲苯的催化氧化,锐钛矿型TiO2较高的电子迁移速率与催化剂孔径的增大均有助于甲苯的氧化降解.     

Effect of transition metal doping under reducing calcination atmosphere on photocatalytic property of TiO2 immobilized on SiO2 beads

TiO₂ immobilized on SiO₂ (TiO₂/SiO₂) have been prepared by sol-gel method and various ions of transition metals (Cr³⁺, Co²⁺, Ni²⁺, Cu²⁺, and Zn²⁺) were doped on the photocatalyst using wet impregnation method under reducing calcination atmosphere. The photocatalytic activity of metal doped TiO₂/SiO₂ towards phenol degradation under black light irradiation were investigated and compared with undoped TiO₂/SiO₂. The results showed that the photoresponse of Cu²⁺ and Zn²⁺ doped TiO₂/SiO₂ were larger than undoped TiO₂/SiO₂, indicating that the photogenerated carriers were separated more efficiently in Cu²⁺ and Zn²⁺ doped TiO₂/SiO₂. The reactivity was in the order of Cu²⁺ > Zn²⁺ > Ni²⁺ > Cr³⁺ > Co²⁺. The different photoreactivity was ascribed to combine effect of the different ionic radii and photocorrison tendency of the dopants. The sample was also characterized by surface analytical methods such as X-ray diffraction, scanning electron micrograph/electron dispersive X-ray analyzer and UV-Vis absorption spectrum.     

多壁碳纳米管的制备与可见光催化性能

采用溶胶-凝胶法,制备了多壁碳纳米管(MWCNTs)/CdS/TiO2复合半导体光催化剂。通过扫描电镜(SEM)、X射线衍射(XRD)和紫外-可见吸收光谱(UV-vis)等分析方法对光催化剂进行了结构表征,并考察了在可见光照射条件下MWCNTs/CdS/TiO2对甲基橙(MO)降解的光催化性能。结果表明,MWCNTs/CdS/TiO2能有效降解甲基橙。低浓度MO降解效果比高浓度好,光催化剂投加量为1.2 g/L即可达到较好的催化效果,酸性条件有利于光催化,投加适宜浓度的H2O(2低于10 mmol/L)时会和催化剂产生协同效果,浓度过大,催化效果下降。阴离子对催化效果有抑制作用,其中PO43-的抑制作用最强。所制备的复合催化剂具有较好的实际应用价值。     

氧气热处理的TiO2纳米管阵列光电催化降解亚甲基蓝的研究

采用原位阳极氧化法在Ti基底上制备了高度有序的TiO2纳米管阵列薄膜,SEM图像表明TiO2纳米管定向排列整齐,分布均匀,其管径范围在70～100 nm.XRD结果证明,阳极氧化法制备的TiO2纳米管为无定型晶型,经退火后为具有良好光催化活性的锐钛矿型.以亚甲基蓝（methylene blue）为目标物研究了TiO2纳米管光电催化性能及影响因素,结果表明,以0.1 mol/L NaCl为电解质,在氧气热处理气氛下,外加偏压为0.5 V、pH=3.25、光照强度为1 000μW/cm2、纳米管薄膜表面积为2 cm×2 cm且MB初始浓度为10 mg/L的条件下,TiO2纳米管阵列薄膜光电催化降解MB的降解效率可达99.56%.电化学阻抗谱分析显示,光电催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

镍掺杂二氧化钛光催化剂的制备与光催化性能研究

利用溶胶-凝胶法制备了镍掺杂的二氧化钛,采用紫外可见分光光度计、傅里叶红外分光光度计、X衍射仪(XRD)、扫描电镜(SEM)等测试手段对结果进行了表征。表征结果表明在550℃下煅烧的产物主要是锐钛型二氧化钛,镍的掺杂使得二氧化钛的紫外可见反射光谱明显红移,且镍掺杂二氧化钛的粒度减小,团聚程度下降。以活性艳蓝KN-R为模型降解目标物,通过比较镍掺杂二氧化钛、纯二氧化钛以及标准P25二氧化钛的光催化性能发现镍掺杂二氧化钛的光催化活性最好。当钛酸正丁酯/乙醇比为1:25;钛酸正丁酯/冰乙酸比为1:1;钛酸正丁酯/硝酸镍比为1 000:3;煅烧温度为550℃,煅烧时间为2 h时,镍掺杂二氧化钛的光催化效率最高,达到73.3%。     

纳米TiO2催化臭氧化对松花江水中氨氮的影响

研究了以负载于陶粒、硅胶、沸石表面的纳米TiO₂作为催化剂时,催化臭氧化松花江水过程中氨氮浓度的变化.结果表明,在单独臭氧化过程中,氨氮浓度先升高后下降,反应30 min后的氨氮浓度与初始浓度相近.在以TiO₂/陶粒、TiO₂/硅胶为催化剂的催化臭氧化过程中,氨氮浓度也是先升高后下降,但反应过程中氨氮的平均浓度要高于单独臭氧化过程.以TiO₂/沸石为催化剂时,催化臭氧化过程中氨氮浓度先下降,然后略有升高,继而又下降,30 min时对氨氮的去除率接近80%.单独臭氧化和催化臭氧化过程中,增大臭氧投量,氨氮浓度最大值出现的时间提前,并且反应过程中氨氮浓度平均值降低.增大催化剂TiO₂/陶粒、TiO₂/硅胶的投量,催化臭氧化过程中氨氮浓度平均值升高.增大TiO₂/沸石投量,有利于氨氮的去除,但投量增大到50g以上时,对氨氮的去除效果影响很小.温度从10℃升高到30℃,对TiO₂/陶粒、TiO₂/硅胶催化臭氧化过程中氨氮浓度的变化影响不大.而以TiO₂/沸石为催化剂时,温度升高有利于催化臭氧化过程中氨氮的去除.     

Effect of platinum on the photocatalytic degradation of chlorinated organic compound

TiO2 nanoparticles, doped with di erent Pt contents, were prepared by a modified photodeposition method using Degussa P-25 TiO2, H2PtCl6 6H2O and methanol as the solvents. The physicochemical properties of Pt/TiO2 were investigated by the nitrogen adsorption and desorption isotherm measurement technique, X-ray di raction analysis and photoluminescence spectra, respectively. Reaction rates from photocatalytic removal of dichloromethane over Degussa P-25 TiO2 and Pt/TiO2 were evaluated. The average diameter and BET surface area of the TiO2 catalyst particles were 300 nm and 50 m2/g, respectively. The degradation e ciency was 99.0%, 82.7%, 55.2%, and 57.9% with TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. And the degradation e ciency was 99.3%, 79.7%, 76.5%, and 73.4% with a 0.005 wt.% Pt/TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. In addition, we found that the photoluminescence emission peak intensities decreased with increases in the doping amount of Pt, which indicates that the irradiative recombination was weakened. Furthermore, the results showed that the UV/0.005 wt.% Pt/TiO2 process was capable of e ciently decomposing gaseous DCM in air.     

TiO2 nanotubes as solid-phase extraction adsorbent for the determination of polycyclic aromatic hydrocarbons in environmental water samples

An analytical method based on TiO2 nanotubes solid-phase extraction (SPE) combined with gas chromatography (GC) was established for the analysis of seven polycyclic aromatic hydrocarbons (PAHs): acenaphtylene, acenaphthene, anthracene, fluorene, phenanthrene, fluoranthene and pyrene. Factors a ecting the extraction e ciency including the eluent type and its volume, adsorbent amount, sample volume, sample pH and sample flow rate were optimized. The characteristic data of analytical performance were determined to investigate the sensitivity and precision of the method. Under the optimized extraction conditions, the method showed good linearity in the range of 0.01–0.8 g/mL, repeatability of the extraction (RSD were between 6.7% and 13.5%, n = 5) and satisfactory detection limits (0.017–0.059 ng/mL). The developed method was successfully applied to the analysis of surface water (tap, river and dam) samples. The recoveries of PAHs spiked in environmental water samples ranged from 90% to 100%. All the results indicated the potential application of titanate nanotubes as solid-phase extraction adsorbents to pre-treat water samples.