铝合金-丁腈橡胶航空带垫卡箍典型环境损伤研究

目的研究典型环境对丁腈橡胶-铝合金带垫卡箍的损伤效应。方法通过模拟铝合金-丁腈橡胶航空带垫卡箍使用时的装配结构和应力状态,应用GJB 150A—2009中的湿热和太阳辐射两种典型老化环境,采用宏观形貌观察、卡箍保持力测试和橡胶衬垫拉伸性能测试方法,结合扫描电子显微镜和傅里叶红外光谱技术,分析带垫卡箍的性能劣化过程。结果带垫卡箍在湿热和太阳辐射环境中老化50 d后,卡箍橡胶衬垫表面出现大量微孔缺陷,拉伸性能大幅降低,导致卡箍保持力分别下降了35%和51%。结论带垫卡箍在模拟装配状态下进行湿热和太阳辐射环境暴露实验,卡箍橡胶衬垫内部结构由致密逐渐变得疏松,部分碳碳双键发生氧化交联反应,并在一定程度上提高了聚合物的交联密度,材料硬度提高,回弹性能减弱,橡胶衬垫对芯轴的包裹能力降低,导致卡箍保持力性能降低。     

金属尖化前缘模型主动式热疏导性能试验研究

目的为了更好地解决高超声速飞行器舵、翼前缘及头锥等气动热环境恶劣区域的热防护问题。方法采用主动式热疏导技术,以高温液态合金为工质,设计并制作具有主动式热疏导功能的尖化前缘金属试验模型(R=5 mm)。根据模型外尺寸设计加工一套石英灯仿形加热器和热流测试模型,开展地面热环境模拟试验。结果试件在前缘中心温度530℃左右时具有瞬态启动特性。前缘中心和大面积中心最大辐射热流密度分别为1000 kw/m^2和580 kw/m^2,试件在该环境中长时间受热状态下仍具有较好的热疏导能力。试验后试件无工质泄漏和结构破坏,具有一定的可重复使用性。结论可以此热疏导方式结合现有成熟热防护技术进一步开展工程设计与应用。     

微生物全细胞传感器在重金属生物可利用度监测中的研究进展

传统的物理化学方法主要用于测定环境重金属的总量,微生物全细胞传感器可以对土壤及水体环境的重金属生物可利用度进行监测.此外,微生物全细胞传感器还具有操作简单、快速、经济的特点,适用于污染事件的应急监测.微生物全细胞传感器的生物学元件主要由MerR、ArsR、RS等家族的金属调控蛋白和gfp、lux、luc等报告基因组成.调控蛋白、报告基因与微生物全细胞传感器的灵敏度、特异性和监测特点有关.受pH、金属螯合物及检测条件等因素的影响,不同的环境条件下的重金属生物可利用度是不同的.增加重金属在微生物细胞内的累积,进行调控蛋白的分子生物学改造,优化检测条件是提高传感器灵敏度、特异性和准确性的可行方案.实现污染物的原位和在线监测是微生物全细胞传感器的主要发展方向.     

蜂窝流道热沉强化传热数值模拟

热沉是模拟太空深冷环境的核心部件。为提高空间深冷环境的模拟效果,更好地满足型号试验需求,设计了一种蜂窝流道热沉。利用流体力学理论和有限元方法对蜂窝热沉内部流体的流动和强化传热进行数值模拟,分析流道结构参数对流体流动和换热的影响,确定最优的流道结构参数。结果表明,同等条件下蜂窝热沉表面温度低于管板式热沉5 K左右,温度均匀性可达到±2 K;流道深度和间距是影响流体在热沉中流动与传热的重要因素,合理选择流道结构参数可以提高热沉的换热性能;需要综合考虑传热和阻力问题来确定最优的流道结构参数,最优的蜂窝热沉流道间距为75 mm,深度为10 mm。     

上海市工业固体废物处理处置现状分析

详细分析了上海市一般工业固体废物及工业危险废物的产生及处理处置现状,提出:一般工业固废主要以资源化利用为主,危废处置企业实行末位淘汰,实现清洁生产;加强国家提倡的"三位一体"综合处理项目建设,实现集中处理、集中监管,降低运营成本;加强工业危废产生企业申报登记及转移的网络信息化管理,杜绝监管盲区。     

排污权交易之排放跟踪数据校核研究

本文以排污权交易的核心业务排放跟踪管理为出发点,选择电厂二氧化硫指标进行排放跟踪数据过程校核体系研究,探索进一步提高排污权交易体系中排放数据准确性的机制。     

Spatial distribution of aerosol pollution based on MODIS data over Beijing, China

With the help of regression analysis,the relationships were detected between aerosol's contribution to apparent reflectance(ACR) derived from Moderate Resolution Imaging Spectroradiometer(MODIS)on board Terra and hourly PM_(10)mass concentration measured at 30 ground-based locations in Beijing for the August of 2003 and 2004.It was shown that there was a good correlation between the ACR and PM_(10)(linear correlation coefficient,R=0.56).On the basis of this relationship,spatial distribution and possible sources of PM_(10)derived from MODIS were analyzed and two frequently heavily-polluted regions were found,namely downtown of the city and the district near Xishan Mountain.These two regions coincidently are also urban heat island centers.The foundings of this paper will be greatly useful for environmental monitoring and urban planning for Beijing,especially for the 2008 Olympic game to be held in Beijing.     

Thermodynamics and kinetics of cadmium adsorption onto oxidized granular activated carbon

Cadmium sorption behavior of granular activated carbon oxidized with nitric acid was systematically studied by sets of the equilibrium and time-based experiments under various conditions.The cadmium adsorption capacity of oxidized granular activated carbon enlarged with an increase in pH,and reduced with an increase in ionic strength.Experimental data were evaluated to find out kinetic characteristics.Adsorption processes were found to follow pseudo-second order rate equation.Adsorption isotherms correlate well with the Langmuir isotherm model and the maximum sorption capacity of cadmium evaluated is 51.02μmol/g.Thermodynamic parameters were calculated based on Van't Hoff equation.Equilibrium constant Kd was evaluated from Freundlich isotherm model constants,Langmnir isotherm model constants,and isotherms,respectively.The average change of standard adsorption heatΔH~0 was -25.29 kJ/mol.NegativeΔH~0 andΔG~0 values indicate the adsorption process for cadmium onto the studied activated carbon is exothermic and spontaneous.The standard entropyΔS~0 was also negative,which suggests a decrease in the freedom of the system.     

不锈钢-气氮板式热沉仿真研究

目的研究不锈钢-气氮板式热沉中,氮气压力、氮气入口流速以及热沉自身流道深度对热沉传热性能的影响。方法利用AnsysFluent软件,对板式热沉壁面温度分布情况以及进出口压力损失进行模拟仿真。结果提高氮气压力和氮气入口速度可以提升热沉的温度均匀性,但热沉进出口压力损失也会增大。对于气氮-板式热沉而言,流道深度的改变对热沉温度均匀性的影响不大,但流道深度较小时,进出口压力损失较大。结论建议在设计气氮-板式热沉时,流道深度选择在8~10 mm,外流程中氮气压力控制在0.3~0.4 MPa,氮气流速控制在20 m/s为宜。     

Minimizing leakage from a smelter off-gas system by enhanced control

The off-gas handling system is a vital component of a smelter and it is essential that it operates in accordance with environmental regulations. A key feature of the off-gas management system is maintaining a slightly negative system pressure to prevent gas leakage, such as SO₂, out into the work and external environments. To enhance sustainable development, there is also growing interest in capturing and reusing the significant amount of heat and CO₂ contained within off-gas. The potential incorporation of heat and CO₂ recovery systems places importance on enhancing control to minimize the risk of both gas leakage and disturbance of the smelting process. With these requirements in mind, an easily implementable feedforward control enhancement to existing control schemes is proposed to help provide improved performance.