岩溶地下河污染物运移模型对比研究

两区模型（TRM）和暂时存储模型（TSM）为两种常用的岩溶地下河（管道）污染物运移模型,为了更好表征岩溶地下河污染物运移过程,开展模型对比研究.采用两种模型拟合室内管道示踪实验穿透曲线,从概念模型框架、模型优缺点、参数校正过程和物理意义、参数敏感性等方面对比分析两种模型的异同.结果表明,OTIS软件提供TSM的数值解,而CXTFIT软件提供TRM的解析解,但两者均能通过下游不同位置的穿透曲线分段表征地下河不同阶段的污染物运移过程.两种模型的物理意义相近,均可近似描述岩溶地下河中溶质的暂时性存储现象,较好地拟合溶质运移曲线.采用TSM可校正得到暂时存储区的横截面积,但采用TRM只能获得非流动区所占的比例.两种模型中弥散系数和传质/交换系数的敏感度较低,并且弥散系数的变化对穿透曲线拖尾无显著影响.研究结果为岩溶地下河污染物运移模型的选取与应用提供了依据.     

北部湾南流江流域土地覆盖及生物多样性模拟

以北部湾独流入海河流南流江流域为研究对象,基于研究区2000年和2015年遥感数据解译的土地利用数据以及社会经济等数据,采用CLUE-S模型对未来2030年生态保护情景、自然增长情景以及粮食安全情景的土地利用格局进行了模拟预测,在此基础上采用InVEST模型对流域过去和未来不同情景的生物多样性进行了评估,探讨了流域生物多样性的生境质量和生境退化程度.结果表明：2000~2015年南流江流域建设用地、园地、水域和未利用地呈现出增加趋势,其中建设用地的增幅最大,而耕地和林地减幅最大.流域土地系统中共存在着34种土地网络转移流关系,上游存在24种,中游20种,下游28种,耕地与建设用地、耕地与林地以及林地与园地之间的转换占到流域总土地利用变化的70.74%.CLUE-S模型模拟未来土地利用的Kappa系数达到0.86,表明模型模拟未来情景的土地利用精度满足要求.2000年、2015年、2030年生态保护情景、2030年自然增长情景以及2030年粮食安全情景流域生境质量总得分和平均得分分别为866630,900357,921055,876231,865370和0.7457,0.7747,0.7925,0.7539,0.7466.2030年3种情景的中上游和下游地区生物多样性都呈现出不同程度的改善趋势,而中游地区则表现出退化趋势.     

pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

Advanced molecular-fingerprinting analysis of dissolved organic sulfur by electrospray ionization-Fourier transform ion cyclotron resonance mass spectrometry using optimal spray solvent

Molecular level characterization of dissolved organic sulfur (DOS) by electrospray ionization-Fourier transform ion cyclotron resonance mass spectrometry (ESI-FTICR MS) is necessary for further understanding of the role of DOS in the environment. Here, ESI spray solvent, a key parameter for ion production during ESI process, was investigated for its effect on the molecular characterization of DOS by ESI-FTICR MS. 100% MeOH as spray solvent was found for the first time to remarkably enhance the ionization efficiency of the majority of CHOS-molecules in NOM, which facilitated a total of 1473 CHOS-molecular formulas with one sulfur atom to be detected. The number of CHOS-molecular formulas obtained using 100%MeOH as spray solvent increased notably over 740 in comparison with those using 50% MeOH aqueous solution (731) or 50% ACN aqueous solution (653). Moreover, due to the enhancement of ionization efficiency of DOS during ESI processes, the tandem mass spectra of the NOM CHOS-molecules could be easily obtained using 100% MeOH as spray solvent, which were hardly obtained using 50% MeOH aqueous solution as spray solvent. The results of the tandem mass spectra suggested the first discovery of organosulfates or sulfonic acids in Suwannee River NOM sample. A simple method based on 100% MeOH as ESI spray solvent for advanced molecular characterization of DOS by ESI-FTICR MS was proposed and applied, and the results revealed more molecular information of DOS in sea DOM samples.     

杭州湾北岸36种挥发性有机物污染特征及来源解析

为研究杭州湾北岸VOCs（挥发性有机物）的浓度水平、组成特征、反应活性和潜在来源,采用GC-FID在线监测系统对杭州湾北岸环境大气中的36种VOCs开展了为期1 a（2017年12月-2018年11月）的连续观测,采用LOH（VOCs的·OH消耗速率）和OFP（O₃生成潜势）2种方法估算了大气VOCs的反应活性,并利用PMF（正定矩阵因子分解）和CPF（条件概率函数）模型分析其来源.结果表明:①φ（VOCs）小时平均值在冬季（26.47×10-9）最高,夏季（9.76×10-9）最低;全年φ（VOCs）小时平均值为21.24×10-9,其中烷烃、烯烃+炔烃、芳香烃、卤代烃的贡献率分别为33.24%、34.13%、15.63%、17.00%;φ（烷烃）、φ（芳香烃）和φ（卤代烃）呈较明显的昼夜变化特征,φ（烯烃）和φ（炔烃）无明显昼夜变化趋势.②大气VOCs的总LOH和OFP分别为9.39 s-1和220.57 μg/m3,KOH（·OH反应速率常数）和MIR（最大增量反应活性）系数的平均值分别为17.34×10-12 cm3/（molecule·s）和3.31;KOH和MIR系数的平均值分别与间/对-二甲苯的KOH和乙苯的MIR系数接近,表明大气VOCs的化学反应活性较强;VOCs关键活性物种为异戊二烯、乙烯、丙烯、甲苯、二甲苯和顺-2-丁烯.③特征物种相关性分析表明,杭州湾北岸大气存在老化现象,异戊烷和正戊烷受煤燃烧源影响较大,二甲苯和乙苯受溶剂排放源影响较大,甲苯和苯除受机动车尾气影响外,还受其他排放源影响.④PMF和CPF模型来源分析表明,大气VOCs主要来自石化工业源、燃料挥发源、生物质燃烧和煤燃烧源、机动车排放源和溶剂使用源,其中,机动车排放源主要来自西北方向,其他源主要来自西北、西和西南方向.研究显示,杭州湾北岸大气VOCs来源复杂,受周边工业区的影响较大.      

基于TMVOC的地下水位波动带苯系物迁移转化模拟

为探究水位波动情况下苯系物的迁移转化规律,提高石油污染场地地下水污染治理精度,以西北某傍河石化场地为研究对象,基于TMVOC模型对特征污染物苯系物开展泄漏模拟,通过情景模拟比较水位波动对苯系物迁移转化的影响,并从污染分布、相间转化等方面,解析地下水位稳定和波动状态下苯系物迁移转化过程差异.结果表明:①TMVOC模型较好地模拟了水位波动状态下苯系物迁移转化过程.②相较于水位稳定状态下,水位波动作用下苯系物污染深度增加0.5 m,污染面积增加25%,总质量增加12 kg.③水位稳定和波动状态下苯系物"气-液-NAPL（Non-Aqueous Phase Liquids）相"占比分别为0.17%、2.03%、97.8%和0.04%、3.69%、96.27%.④NAPL相苯系物饱和度分布与苯系物质量分布呈正相关,水位波动造成NAPL相初始饱和度降低,且初始水位面以下NAPL相饱和度升高.⑤对于苯而言,水位波动状态下非饱和带中苯在液相中的质量是水位稳定状态下的1.11倍,饱和带为10.15倍.研究显示,水位波动显著地影响了苯系物的迁移转化过程,促进了苯系物的溶解,并使更多的苯系物残留在地下介质中.      

厦门市冬季PM2.5污染情境识别及其与气象条件的关系

为研究厦门市冬季不同PM_2.5污染情境与气象条件和气团轨迹路径特征的关系,结合PM_2.5观测数据,使用AGAGE（Advanced Global Atmospheric Gases Experiment）统计方法识别2014—2018年冬季厦门市PM_2.5观测值、基线值和污染值情境,通过气象数据统计和气团后向轨迹聚类对不同PM_2.5污染情境下气象条件和气团轨迹路径特征进行探究.结果表明:①厦门市冬季不同PM_2.5污染情境下,ρ（PM_2.5）及PM_2.5污染值情境时长占比均呈波动中下降的趋势,具体表现为冬季PM_2.5观测值、污染值和基线值情境下,ρ（PM_2.5）平均值分别从2014年的42.2、90.7、16.4 μg/m3降至2018年的26.3、56.9、8.8 μg/m3,冬季PM_2.5污染值情境时长占比从2014年的10.2%降至2018年的3.0%.②冬季PM_2.5污染值情境下气象要素呈低风速、低气压、高温度、高相对湿度的特征.③冬季到达厦门市的气团轨迹路径中,局地路径由于大气条件稳定易累积形成PM_2.5污染;偏北路径和西北路径易从临近省份携带污染物输入导致PM_2.5污染,属于重要的外源污染输入路径;沿海路径和偏西路径均属于清洁路径,但沿海路径易在福建省北部与偏北路径重合形成污染输入,加强了偏北路径的污染物输送能力.研究显示,近年来厦门市冬季PM_2.5污染有明显减弱趋势,但不利的气象条件和外来污染输入仍会造成PM_2.5污染的发生.      

Concentrations and chemical compositions of PM10 during hazy and non-hazy days in Beijing

In order to study the concentrations of major components,characteristics and comparison in hazy and non-hazy days of PM_(10) in Beijing,aerosol samples were collected at urban site in Beijing from December 29,2014 to January 22,2015.Heavy metals like Zn,Pb,Mn,Cu,As,V,Cr and Cd were deeply studied considering their toxic effects on human being;nine water-soluble inorganic ions(SO_4~(2-),NO_3~-,NH_4~+,Na~+,K~+,Cl~-,Ca~(2+) and Mg~(2+)) and carbon fractions(OC and EC) were also analyzed.The concentrations of heavy metals were 1.03–1.98 times higher in hazy days than those in non-hazy days,mainly due to biomass burning and coal burning.The trends in total heavy metals concentrations were basically consistent with the trends in PM concentrations except for two obvious periods(12.29–12.30;1.14–1.15);but when air masses accumulated locally or around Beijing,trends in PM concentrations and heavy metals were opposite.The proportion for NO_3~-/SO_4~(2-) indicated that mobile sources such as automobiles were important reasons for haze in Beijing.Correlation between OC and EC during non-hazy days was strong(R~2= 0.95) but it was low(R~2= 0.67) during hazy days,and large variations for OC/EC values occurred in hazy days.The calculated mass concentration of SOC is 2.58 μg/m~3,which only accounted for 10.1% of the OC concentration.When air masses from the far north-west,they decreased PM concentration in Beijing and they were relatively clean;however,those from the near east,south-east and south of the mainland increased PM concentration and they were dirty.     

内饰材料发射率对密封舱室热防护效率的影响

目的探究密封舱室热防护效率与其内饰材料表面发射率的关系,分析内饰材料发射率对其表面温度、舱室内温度的影响规律。方法采用自行设计的小型密封舱室和加热测量装置,对内饰材料表面及舱室内温度进行测量。结果当内饰材料发射率为0.09时,内饰表面温度为141.2℃,舱室内平均温度仅为90.8℃;内饰材料发射率为0.91时,内饰表面温度为124.4℃,舱室内平均温度为109.1℃。结论试样表面温度随材料发射率的提高而降低,舱室内部空气平均温度随材料发射率的提高而升高;试样表面温度与舱室空气平均温度的温度差随材料发射率的提高而减小;同时,相同试样表面温度与舱室平均温度的温度差随加热温度的提高而增加。