Stabilization and utilization of hospital waste as road and asphalt aggregate

This article reports the operational results of the effective utilization of hospital waste molten slag produced using a high-temperature melting system, and being operated at a hospital in Selangor, Malaysia. The hospital waste is incinerated and subsequently melted at 1200°C. Scanning election microscope (SEM)/EDX results showed that the slag produced after melting contained amounts of SiO₂, CaO, and Al₂O₃ in excess of 53%, 9%, and 16%, respectively. The results from a leaching analysis on the slag produced proved that the melting process had successfully stabilized the heavy metals. The use of this slag as an alternative material to replace conventional aggregates for road construction was studied. The results from aggregate and asphalt mix tests showed that the slag produced fulfills all the requirements of an alternative aggregate. The average asphalt content, or the optimum asphalt content to be mixed with hospital waste molten slag, was found to be about 5.53%.     

Clam shell catalyst for continuous production of biodiesel

Continuous flow transesterification of waste frying oil (WFO) with methanol for the biodiesel production was tested in a laboratory scale jacketed reactive distillation (RD) unit packed with clam shell based CaO as solid catalyst. The physiochemical properties of the clam shell catalysts were characterized by X-ray Diffraction (XRD), Brunauer–Emmett–Teller (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive Atomic X-ray Spectrometry (EDAX). The effects of the reactant flow rate, methanol-to-oil ratio, and catalyst bed height were studied to obtain the maximum methyl ester conversion. Reboiler temperature of 65°C was maintained throughout the process for product purification and the system reached the steady state at 7 hr. The experimental results revealed that the jacketed RD system packed with clam shell based CaO showed high catalytic activity for continuous production of biodiesel and a maximum methyl ester conversion of 94.41% was obtained at a reactant flow rate of 0.2 mL/min, methanol/oil ratio of 6:1, and catalyst bed height of 180 mm.     

Fenton法处理垃圾渗滤液的参数优化及反应动力学模型

采用Fenton法处理垃圾渗滤液,研究反应时间、初始浓度、pH、Fenton试剂用量对垃圾渗滤液TOC去除率的影响。研究结果表明,最优反应条件是反应时间30 min,初始pH为3.0,初始[H2O2]0=7 310 mg/L,最佳[H2O2]/[Fe2+]摩尔比为5,反应温度为室温,此时渗滤液的TOC去除率达到70.3%。渗滤液矿化过程符合一级反应动力学,并建立了符合该渗滤液的反应动力学模型。     

吸附—电化学法组合工艺处理废乳化液

以季铵盐改性硅藻土为吸油剂,采用吸附—电化学组合工艺处理拉丝废乳化液,优化了工艺条件。实验结果表明,在乳化液pH为5.0、吸油剂加入量为20 g/L、反应温度为25 ℃的最优条件下吸附除油15 min,然后在清液pH为8.5、阳极电流密度为4 A/dm²的最优条件下电化学反应4 h后,废水无色无味,COD为43 mg/L,ρ（NH₃-N）=0,ρ（Cu）= 1.6 mg/L,ρ（Zn）= 3.7 mg/L,浊度为1.1 NTU,达到GB 8978—1996污水综合排放标准。     

Composting of waste algae: A review

Although composting has been successfully used at pilot scale to manage waste algae removed from eutrophied water environments and the compost product applied as a fertiliser, clear guidelines are not available for full scale algae composting. The review reports on the application of composting to stabilize waste algae, which to date has mainly been macro-algae, and identifies the peculiarities of algae as a composting feedstock, these being: relatively low carbon to nitrogen (C/N) ratio, which can result in nitrogen loss as NH₃ and even N₂O; high moisture content and low porosity, which together make aeration challenging; potentially high salinity, which can have adverse consequence for composting; and potentially have high metals and toxin content, which can affect application of the product as a fertiliser. To overcome the challenges that these peculiarities impose co-compost materials can be employed.     

Chemical and process mineralogical characterizations of spent lithium-ion batteries: An approach by multi-analytical techniques

Mineral processing operation is a critical step in any recycling process to realize liberation, separation and concentration of the target parts. Developing effective recycling methods to recover all the valuable parts from spent lithium-ion batteries is in great necessity. The aim of this study is to carefully undertake chemical and process mineralogical characterizations of spent lithium-ion batteries by coupling several analytical techniques to provide basic information for the researches on effective mechanical crushing and separation methods in recycling process. The results show that the grade of Co, Cu and Al is fairly high in spent lithium ion batteries and up to 17.62 wt.%, 7.17 wt.% and 21.60 wt.%. Spent lithium-ion batteries have good selective crushing property, the crushed products could be divided into three parts, they are Al-enriched fraction (+2 mm), Cu and Al-enriched fraction (?2 + 0.25 mm) and Co and graphite-enriched fraction (?0.25 mm). The mineral phase and chemical state analysis reveal the electrode materials recovered from ?0.25 mm size fraction keep the original crystal forms and chemical states in lithium-ion batteries, but the surface of the powders has been coated by a certain kind of hydrocarbon. Based on these results a flowsheet to recycle spent LiBs is proposed.     

Stakeholders' expectations from the agri-environmental programme in Slovenia and Croatia

The agri-environmental programme (AEP) is the European Union policy instrument used for the delivery of environmental services expected by the society, but societal expectations for these environmental services are insufficiently assessed. In order to realistically meet the expectations of AEP, this research utilises analytical hierarchy process based web survey to assess the importance that various societal stakeholders in the European countries of Slovenia and Croatia give to specific environmental services and to also identify the agricultural practices that have the greatest potential to realise the expectations that society values the most. All stakeholders (overall group) from Slovenia and Croatia ranked water quality and availability as the first most important environmental service, and reduction of pesticides as the most important agricultural practice to deliver societal expectations. The results indicate that there is similar demand for environmental services in these two countries that differ in their agricultural settings.     

化工装置停工放空过程中VOCs排放及估算方法

通过分析化工企业典型开、停车过程的排污节点，表明停车过程中大气挥发性有机污染物主要来自装置退料结束后挂壁、底部滞留和内部空间蒸气等滞留在设备内部的残余物料。在总结化工装置停工放空过程中大气挥发性有机物来源的基础上，讨论并提出大气污染排放量估算方法。     

固体废物全过程管理中固体废物鉴别研究

对固体废物应进行全过程管理,固体废物鉴别是固体废物全过程管理的基础和关键,包括依据产生来源鉴别和过程鉴别两种方法,依据产生来源鉴别包括丧失原有利用价值的物质、在生产过程中产生的副产物、环境治理和污染控制过程中产生的物质、其他物质四类,在每一类中详细地列举了属于该产生来源的具体固体废物种类名称,便于理解和增强可操作性。过程鉴别包括在固体废物再生利用过程和处置过程中的固体废物鉴别两类,其中在再生利用过程的固体废物鉴别中明确指出了固体废物再生利用产物只有同时满足产品质量标准要求、国家污染控制标准要求以及有实际市场需求、固定用户等条件时,才不作为固体废物管理,在处置过程的固体废物鉴别中具体地列出了处置固体废物全过程中仍然作为固体废物管理的国际惯用处置方式。同时,给出了清晰的"原料—产品—固体废物—处置或产品"全过程中固体废物的产生节点和相应的固体废物类别图,为固体废物鉴别工作提供参考,使固体废物全过程管理有的放矢,有效防止固体废物对环境和人体健康造成的危害。     

柴油低温临界吸收法回收装车挥发油气

研究了采用柴油低温临界吸收法回收装车挥发油气的效果。实验结果表明：按装车挥发油气中的总烃体积分数为20.88%、装车挥发油气流量为280 m³/h、年运行时间为2 668 h计，装置年回收油气量为291 t，装置年最大运行功率为206.770 MW，装置投资回收期为3 a;处理后净化气中的总烃体积分数为1.24%，排放质量浓度低于25 g/m³，油气回收率达95%。处理后净化气满足GB 20950—2007《储油库大气污染物排放标准》，取得了较好的环保效益和经济效益。