一个烟厂除味系统

在对烟草进行加工制烟的过程中 ,会产生一定量的异味气体 ,污染烟厂及周围环境。在此介绍了某卷烟厂除味系统的基本原理、系统组成及运行情况。初步的运行表明该除味系统除味效率可达 95 %。     

常压非平衡态等离子体降解挥发性烃类污染物

采用无声放电产生的非平衡态等离子体,对含有易挥发性有机化合物正己烷、环己烷、苯和甲苯4种典型的烃类废气的空气进行了处理．结果表明,对于一个大气压下正己烷含量（体积分数）为0．26％、0．79％、13％的宁气,在12kV的电压下放电ls,正己烷的降解率分别为88％、81.8％、64．9％．含有环己洗、苯及甲苯浓度为0．26％的空气,在同样的条件下,放电ls后,环己烷、苯及甲苯降解率分别为87．4％、8l％和70．3％,其主要降解产物为CO₂和H₂O．还研究了污染物浓度与氧含量对非平衡态等离子体法降解挥发性烃类污染物的影响     

介质阻挡放电降解环境污染物CF2ClBr的等离子体系电子密度

在利用介质阻挡放电对污染物质ＣＦ２ＣｌＢｒ进行等离子体降解产物分析的基础上,进一步研究等离子体系中的电子密度。采用动态反应装置,以平行板电极法直接测量。在ＣＦ２ＣｌＢｒ的压力为２ｋＰａ时,得出该实验条件下的电子密度约为５．０×１０＾１３／ｍ＾３。     

有毒有害气体低温等离子体催化处理反应器

等离子体催化技术是目前国内外公认的治理低浓度有害气体的有效方法之一。本文概述了填充床式反应器、点对板式反应器、平板式反应器和复合式反应器中利用低温等离子体结合催化剂处理有害废气的研究结果,并对反应器的结构、脱除效率及应用情况作了介绍。     

DBD反应器关键操作参数对2,4-二氯酚去除的影响

采用同轴喷雾式介质阻挡放电(DBD)反应器处理2,4-二氯酚(2,4-DCP)模拟废水,考察了水质、废水流量、载气流量、放电频率等关键操作参数对2,4-DCP去除的影响。自来水中的CO₃^2-/HCO₃^-能够中和生成的硝酸/亚硝酸(载气含N₂),同时也能清除放电过程中产生的自由基,因而不利于2,4-DCP的去除。在DBD反应器的操作参数中,载气流量对于活性组分的产生及气相到液相的传质有显著影响,是最为关键的操作参数。反应器操作参数的变化会影响放电过程。同轴式反应器和废水雾化对污染物的矿化有利。在废水流量50 mL/min、载气流量15 L/min、放电频率17 kHz的最佳条件下处理60 min,2,4-DCP和TOC的去除率分别为69.77%和31.85%。     

吸附存储-间歇放电法氧化甲苯的反应过程研究

以SBA-15为催化剂,对比连续降解法和吸附存储-间歇放电法净化低浓度甲苯的活性,结果表明吸附存储-间歇放电法下甲苯去除率、碳平衡和CO2选择性更高.运用GC-MS分析了2种降解方式催化剂表面中间产物随时间的变化,苯甲醛进一步氧化分解进而打开苯环,是等离子体催化降解甲苯的控制步骤.对比SBA-15、Mn/SBA-15、Ag/SBA-15、AgMn/SBA-15 4种催化剂在吸附存储-间歇放电法下降解甲苯的活性.结果显示Ag和Mn的引入加速了对2-庚烯醇的氧化催化,AgMn/SBA-15表现出最好的碳平衡、CO2选择性.     

污水处理厂低温等离子体恶臭治理技术

利用低温等离子体技术处理污水厂恶臭气体,是一种新的技术。介绍了该技术处理恶臭的机理和相关工程的工艺流程以及处理效果,实际应用表明该技术对污水处理厂恶臭气体的治理是十分有效的。     

Gliding arc plasma processing for decomposition of chloroform

The decomposition of chloroform (CHCl₃) diluted in air was studied. The experiment was carried out by using a gliding arc plasma. Different values of initial concentrations of chloroform, total gas flow rates, and input power frequencies have been used to investigate this effects on the conversion reaction products both qualitatively and quantitatively. Experimental results indicate that the maximum conversion of chloroform was 97% at a total gas flow rate of 180?L?h^?1 containing 1% chloroform. Using air as carrier gas, decomposition of CHCl₃ produces CCl₄, CO₂, CO, and Cl₂ as the main products. Small amounts of HCl and COCl₂ are also detected. Liquid products were also produced.     

Automated indirect fluoride determination by ICP-OES using discontinuous-flow analysis

An automated method for the indirect determination of fluoride by inductively coupled plasma atomic emission spectrometry using discontinuous-flow analysis has been developed. A modified flow injection analysis system was used for sample preparation. The method is based on the determination of excess cerium(III) ion after precipitation of CeF₃. Separation of the precipitate is performed online on a syringe membrane filter that is cleaned each analysis cycle by 1 M nitric acid, ensuring a long life-time for the filter. As a result of the short reaction time, a detection limit of 9.5 mg L^?1 was obtained. The precision (RSD) of the proposed method is 1.02% at fluoride concentration of 28 mg L^?1. The applicability of the technique for groundwater monitoring of fluoride-contaminated area is demonstrated.     

Assessment of potentially toxic elements in Swiss chard and sediments of Akaki River,Ethiopia

For the determination of 15 potentially toxic elements (V, Cr, Fe, Mn, Co, Ni, Cu, Zn, As, Se, Ag, Cd, Sn, Hg, and Pb) in plant and sediment samples of the Akaki River, Ethiopia, inductively coupled plasma–mass spectrometry, inductively coupled plasma–optical emission spectrometry, and a RA-915+ mercury analyzer were applied. Sediment and plant samples were mineralized using a closed-vessel microwave-assisted digestion system. The elemental concentrations varied considerably in plant and sediment samples. The minimum concentration was observed for known toxic elements (As, Hg, and Cd) while the highest concentration was observed for the elements of relatively low toxicity Zn, Mn, and Fe. The concentration of Cr, Fe, Pb, Zn, and As in Swiss chard surpassed the maximum permissible levels at specific sites. At some of the sites, the sediment quality guidelines are surpassed for Cu, Zn, and Pb.