Mesoporous WO3-graphene photocatalyst for photocatalytic degradation of Methylene Blue dye under visible light illumination

Advanced oxidation technologies are a friendly environmental approach for the remediation of industrial wastewaters. Here, one pot synthesis of mesoporous WO_3 and WO_3-graphene oxide(GO) nanocomposites has been performed through the sol–gel method. Then, platinum(Pt) nanoparticles were deposited onto the WO_3 and WO_3-GO nanocomposite through photochemical reduction to produce mesoporous Pt/WO_3 and Pt/WO_3-GO nanocomposites. X-ray diffraction(XRD) findings exhibit a formation of monoclinic and triclinic WO_3 phases. Transmission Electron Microscope(TEM) images of Pt/WO_3-GO nanocomposites exhibited that WO_3 nanoparticles are obviously agglomerated and the particle sizes of Pt and WO_3 are ~ 10 nm and 20–50 nm, respectively. The mesoporous Pt/WO_3 and Pt/WO_3-GO nanocomposites were assessed for photocatalytic degradation of Methylene Blue(MB) as a probe molecule under visible light illumination.The findings showed that mesoporous Pt/WO_3, WO_3-GO and Pt/WO_3-GO nanocomposites exhibited much higher photocatalytic efficiencies than the pure WO_3. The photodegradation rates by mesoporous Pt/WO_3-GO nanocomposites are 3, 2 and 1.15 times greater than those by mesoporous WO_3, WO_3-GO, and Pt/WO_3, respectively. The key factors of the enhanced photocatalytic performance of Pt/WO_3-GO nanocomposites could be explained by the highly freedom electron transfer through the synergetic effect between WO_3 and GO sheets, in addition to the Pt nanoparticles that act as active sites for O2 reduction, which suppresses the electron hole pair recombination in the Pt/WO_3-GO nanocomposites.     

7B04铝合金和30CrMnSiA钢短期腐蚀的电化学行为研究

目的研究7B04铝合金和30CrMnSiA合金钢试样的电化学性能。方法采用电化学实验、扫描电子显微镜(SEM)、腐蚀坑深度测试分别对7B04铝合金和30CrMnSiA合金钢试样在是否经过天然海水浸泡的情况下进行测试分析,得到微观腐蚀形貌和腐蚀坑深度以及试样表面不带锈和带锈时的电化学性能。结果随着Na Cl浓度增大,7B04铝合金和30CrMnSiA钢的自腐蚀电流变大,两者之间存在明显的电位差,接触后会发生电偶腐蚀。电偶电流与阴阳极面积比和Na Cl浓度有关,阴阳极面积比增大或Na Cl浓度升高均会导致电偶效应增强。经过海水短期浸泡后,7B04铝合金表面的锈层不仅没有起到抑制腐蚀的作用,反而使自腐蚀加重,但电偶效应确实有所减弱。结论沿海设备在使用过程中应竭力避免铝合金在锈层下工作。     

可靠性强化试验技术在某型伺服作动器研制中的适用性探索

目的探索可靠性强化试验技术在典型机电液一体化产品伺服作动器研制过程中的适用性。方法以某型伺服作动器为研究对象,从故障激发的角度对可靠性强化试验技术的应用进行可行性分析,在响应调查和应力分析的基础上,结合产品的工作特点设计适用于该类伺服作动器的可靠性强化试验方案,包含低温步进应力试验、高温步进应力试验、快速温度循环试验10个循环、振动步进应力试验(包含气锤式三轴向六自由度超高斯随机振动方式及电磁振动台随机振动方式)及综合环境应力试验5个循环,并依此进行试验。结果在快速温度循环试验及综合环境应力试验过程中,均有效地激发出了产品的漏油故障,与相似产品外场暴露的漏油故障模式相吻合。结论可靠性强化试验技术可有效地应用于典型机电液一体化产品伺服作动器的研制过程,设计的可靠性强化试验方案可有效地激发外场出现频率较高的故障,可作为该类产品研制的试验手段之一。     

“天舟一号”货运飞船在轨污染探测数据分析

目的分析"天舟一号"(TZ-1)货运飞船的空间污染探测器的在轨探测数据。方法 TZ-1货运飞船上的污染探测器采用石英晶体微量天平(QCM),利用污染物沉积在QCM探测器传感晶片表面引起的振荡频率变化情况来分析航天器在轨空间污染环境。根据其探测原理,通过分析下传的原始数据,得到航天器在轨的污染累积量结果。结果航天器在轨飞行过程中,污染累积已达到会导致污染敏感器件光学性能明显退化的程度,并且污染源温度是影响航天器污染累积量的一个重要因素,可以将其作为航天器在轨污染控制的重要措施。结论该研究结果可以为航天器污染设计、控制提供参考,为提高航天器可靠性设计提供数据支持。     

碳量子点掺杂氮化碳提高的光电化学阴极保护性能研究

目的研究g-C_3N_4/C-Dots-M复合材料的光电化学阴极保护性能。方法采用X射线衍射(XRD)、扫描电子显微镜(SEM)和紫外可见漫反射光谱技术对样品的晶体结构、微观形貌和光吸收性能进行表征。通过电化学测试可见光照射下g-C_3N_4/C-Dots-M复合材料光电极偶联316L不锈钢后的光电化学阴极保护电流密度和电位变化曲线,研究材料的光电化学阴极保护性能。结果可见光照射下,该偶联体系的光致混合电位下降至-0.43 V(vs. Ag/AgCl),光电化学阴极保护电流密度达到4.3μA/cm。结论得益于碳量子点优异的电子传导特性,g-C_3N_4/C-Dots-550复合材料的光电化学阴极保护性能比纯g-C_3N_4的明显增强。该复合材料在光电化学阴极保护方面展现了较大的应用潜力。     

DZ125合金HY3包覆型涂层退除研究

目的 研究化学法退除DZ125合金HY3包覆型涂层。方法 采用真空电弧镀技术（AIP）在定向凝固镍基高温合金DZ125上制备包覆型涂层HY3,利用化学方法完全退除基体上的涂层,通过失重法研究对比1#和2#退除溶液退除HY3涂层和DZ125合金的退除速率,采用扫描电镜（SEM）对退除后的HY3涂层和DZ125基体的微观组织进行观察。结果 经过100 min,2#溶液可以将20 ?m左右的HY3涂层完全退除,采用1#溶液需要超过100 min才能完全退除涂层。两种对DZ125合金的腐蚀性很小,对于同一种合金而言,1#溶液和2#溶液对合金的腐蚀速率比值为1︰13。在1#溶液中,合金与涂层腐蚀速率的比值为1︰87.65;在2#退除溶液中,合金与涂层腐蚀速率的比值为1︰6.81。结论 1#溶液更加适合退除DZ125合金上的HY3涂层。     

固相微萃取-毛细管气相色谱法快速同步分析水中有机氯及有机磷农药

固相微萃取是一种快速、简便,集萃取浓缩进样于一体的样品前处理技术,具有分析时间短、灵敏度高、无需有机溶剂的优点.用固相微萃取富集水中8种有机氯及7种有机磷农药,毛细管气相色谱ECD检测器分离分析,整个分析过程只需26min,检出限可达0.002～1μg/L,已用于地表水中有机氯及有机磷农药含量的测定.     

Desert Water Harvesting to Benefit Wildlife: A Simple, Cheap, And Durable Sub-Surface Water Harvester for Remote Locations

A sub-surface desert water harvester was constructed in the sagebrush steppe habitat of south-central Idaho, U.S.A. The desert water harvester utilizes a buried micro-catchment and three buried storage tanks to augment water for wildlife during the dry season. In this region, mean annual precipitation (MAP) ranges between about 150–250 mm (6″–10″), 70% of which falls during the cold season, November to May. Mid-summer through early autumn, June through October, is the dry portion of the year. During this period, the sub-surface water harvester provides supplemental water for wildlife for 30–90 days, depending upon the precipitation that year. The desert water harvester is constructed with commonly available, “over the counter” materials. The micro-catchment is made of a square-shaped, 20 mL. “PERMALON” polyethylene pond liner (approximately 22.9 m × 22.9 m = 523 m²) buried at a depth of about 60 cm. A PVC pipe connects the harvester with two storage tanks and a drinking trough. The total capacity of the water harvester is about 4777 L (1262 U.S. gallons) which includes three underground storage tanks, a trough and pipes. The drinking trough is refined with an access ramp for birds and small animals. The technology is simple, cheap, and durable and can be adapted to other uses, e.g. drip irrigation, short-term water for small livestock, poultry farming etc. The desert water harvester can be used to concentrate and collect water from precipitation and run-off in semi-arid and arid regions. Water harvested in such a relatively small area will not impact the ground water table but it should help to grow small areas of crops or vegetables to aid villagers in self-sufficiency.     

CTL-12型化学需氧量速测仪与标准法测定CODCr之比较

使用CTL—12型化学需氧量速测仪分析废水化学需氧量，简便、快速，且方法可行，完全能满足环境监测技术要求。     

膜、柱串联固相萃取-高效液相色谱法测定水中多环芳烃(PAHs)的研究

建立了用膜-柱串联固相萃取(SPE)技术,甲醇和水作为流动相进行梯度洗脱,紫外和荧光检测器串联的高效液相色谱法(HPLC)分析水中EPA优先监控的16种PAHs的方法.