The biological effect of metal ions on the granulation of aerobic granular activated sludge

As a special biofilm structure, microbial attachment is believed to play an important role in the granulation of aerobic granular activated sludge (AGAS). This experiment was to investigate the biological effect of Ca^2 +, Mg^2 +, Cu^2 +, Fe^2 +, Zn^2 +, and K⁺ which are the most common ions present in biological wastewater treatment systems, on the microbial attachment of AGAS and flocculent activated sludge (FAS), from which AGAS is always derived, in order to provide a new strategy for the rapid cultivation and stability control of AGAS. The result showed that attachment biomass of AGAS was about 300% higher than that of FAS without the addition of metal ions. Different metal ions had different effects on the process of microbial attachment. FAS and AGAS reacted differently to the metal ions as well, and in fact, AGAS was more sensitive to the metal ions. Specifically, Ca^2 +, Mg^2 +, and K⁺ could increase the microbial attachment ability of both AGAS and FAS under appropriate concentrations, Cu^2 +, Fe^2 +, and Zn^2 + were also beneficial to the microbial attachment of FAS at low concentrations, but Cu^2 +, Fe^2 +, and Zn^2 + greatly inhibited the attachment process of AGAS even at extremely low concentrations. In addition, the acylated homoserine lactone (AHL)-based quorum sensing system, the content of extracellular polymeric substances and the relative hydrophobicity of the sludges were greatly influenced by metal ions. As all these parameters had close relationships with the microbial attachment process, the microbial attachment may be affected by changes of these parameters.     

The role of lipids in fermentative propionate production from the co-fermentation of lipid and food waste

● Lipid can promote PA production on a target from food waste. ● PA productivity reached 6.23 g/(L∙d) from co-fermentation of lipid and food waste. ● Lipid promoted the hydrolysis and utilization of protein in food waste. ● Prevotella , Veillonella and norank _f _Propioni bacteriaceae were enriched. ● Main pathway of PA production was the succinate pathway. Food waste (FW) is a promising renewable low-cost biomass substrate for enhancing the economic feasibility of fermentative propionate production. Although lipids, a common component of food waste, can be used as a carbon source to enhance the production of volatile fatty acids (VFAs) during co-fermentation, few studies have evaluated the potential for directional propionate production from the co-fermentation of lipids and FW. In this study, co-fermentation experiments were conducted using different combinations of lipids and FW for VFA production. The contributions of lipids and FW to propionate production, hydrolysis of substrates, and microbial composition during co-fermentation were evaluated. The results revealed that lipids shifted the fermentation type of FW from butyric to propionic acid fermentation. Based on the estimated propionate production kinetic parameters, the maximum propionate productivity increased significantly with an increase in lipid content, reaching 6.23 g propionate/(L∙d) at a lipid content of 50%. Propionate-producing bacteria Prevotella, Veillonella, and norank_f_Propionibacteriaceae were enriched in the presence of lipids, and the succinate pathway was identified as a prominent fermentation route for propionate production. Moreover, the Kyoto Encyclopedia of Genes and Genomes functional annotation revealed that the expression of functional genes associated with amino acid metabolism was enhanced by the presence of lipids. Collectively, these findings will contribute to gaining a better understanding of targeted propionate production from FW.     

Recent advances in three typical configurations and applications of bioelectrochemical systems北大核心CSCD

As the world's freshwater resources and available energy are alarmingly decreasing, the bioelectrochemical system (BES) is a cutting-edge technology for the resolution of the resource and energy issue. Researchers have paid much attention to t he application of t he BES configuration. Based on t he brief i ntroduction of m icrobial f uel cell a nd m icrobial electrolytic cell structure, principles, and domestic and foreign research, the BES and its influencing factors are introduced, specifically including: microbial activity, electrode materials, and configuration. Three important aspects (i.e., the electrode chamber, the reaction chamber, and micro-sensor) are summarized, and the advantages and disadvantages of single-electrode and multi-electrode chambers are compared, based on the microbial desalination cell. Microbial electrolysis desalination cell: Microbial electrolysis desalination and chemical-production cell have been discussed to introduce increasing reaction chamber configuration; this review focuses on the research of BES monitoring with regards to biochemical oxygen demand. The potential applications of the research progress are explored. The results show that the configuration of multi-chamber microbial fuel cell is complex and its efficiency is low, while the single chamber configuration is advantageous. The reaction chamber added is mainly aimed at desalination, and the study of the desalination pool still needs to be focused on optimizing the cation exchange membrane to maintain the anode pH balance and reduce the air cathode dissolved oxygen. Microbial electrode sensor can be applied in more areas, and its sensitivity and long-term stability need to be further improved. However, there is relatively less research on the abundance and activity of electricigen communities; the configurations and scopes of application of BES are still the research priority. © 2018 Science Press. All rights reserved.     

Effect of iron addition on the performance of anoxic-oxic membrane process and biological phosphorus removal北大核心CSCD

In order to solve the problem of poor treatment of phosphorus in membrane bioreactor (MBR) with long sludge retention time (SRT), a ferric salt was added to enhance phosphorus removal; FeCl36H2O (Fe/P = 2.0) was added to the reactor. The removal efficiency of nitrogen, organic matters, and phosphorus in the MBR was investigated systematically. Moreover, this study focused on the membrane performance, the change of active sludge flora, and the effect of adding a ferric salt on membrane fouling before and after the addition. It was seen that adding the ferric salt could not affect the removal of COD and NH4 +-N and the removal rate of COD and NH4 +-N reached over 90%. However, the average removal rate of phosphorus was 52%, while the removal rate increased by nearly 40% after adding the ferric salt. The effects of adding ferric salts on the dominant bacteria and biological phosphorus removal of activated sludge were further studied. The results showed that the addition of ferric salt (Fe/P = 2.0) decreased the diversity of active sludge flora and relative abundance of some phosphorusaccumulating organisms and had a negative effect on biological phosphorus removal. The analysis of transmembrane pressure difference (TMP) recording revealed that the concentration of iron salts did not exacerbate membrane fouling. The results showed that the concentration of iron salts entering the membrane bioreactor would reduce the relative abundance and phosphorus removal efficiency of the activated sludge in the system to a certain extent, but it had no obvious effect on membrane fouling. It allowed the effluent to attain acceptable standards, especially with respect to phosphorus removal efficiency. © 2018 Science Press. All rights reserved.     

基于活性污泥微生物冻后再生对废水基质降解效能的研究

采用高径比为12.5的序批式反应器(SBR)对冷冻的成熟好氧颗粒污泥（AGS）解冻驯化,研究母体颗粒冻后富集培养及其在番茄废水基质降解中的循环利用。结果表明：冻后恢复活性的污泥第60天全部颗粒化,平均粒径不小于0.45 mm;高通量测序结果显示,相较母体颗粒,该污泥中与颗粒化相关的变形菌门(Proteobacteria)和拟杆菌门(Bacteroidetes)优势菌群富集,微生物丰度呈显著差异（P<0.05）;复合菌株对COD、NH3-N和PO3-4-P去除率分别为98.9%、82.1%和82.2%,可实现番茄废水的有效降解。     

一种微生物絮凝剂絮凝特性的研究

实验表明,在一定条件下,黑曲霉所产微生物絮凝剂对高岭土悬浊液的絮凝率能达到96％以上,该微生物絮凝荆在pH值很低的情况下亦能保持较高的絮凝活性,添加助凝剂CaCl2能大幅提高絮凝率。该絮凝剂的絮凝效果不易受温度的影响,其最佳投加量为2mL／100mL。     

Co-metabolic and biochar-promoted biodegradation of mixed PAHs by highly efficient microbial consortium QY1

Polycyclic aromatic hydrocarbons (PAHs), typical representatives of the persistent organic pollutants (POPs), have become ubiquitous in the environment. In this study, a novel microbial consortium QY1 that performed outstanding PAHs-degrading capacity has been enriched. The degradation characteristics of single and mixed PAHs treated with QY1 were studied, and the effect of biochar on biodegradation of mixed PAHs and the potential of biochar in PAHs-heavy metal combined pollution bioremediation were also investigated. Results showed that, in single substrate system, QY1 degraded 94.5% of 500 mg/L phenanthrene (PHE) and 17.8% of 10 mg/L pyrene (PYR) after 7 days, while in PHE-PYR mixture system, the biodegradation efficiencies of PHE (500 mg/L) and PYR (10 mg/L) reached 94.0% and 96.2%, respectively, since PHE served as co-metabolic substrate to have significantly improved PYR biodegradation. Notably, with the cooperation of biochar, the biodegradations of PHE and PYR were greatly accelerated. Further, biochar could reduce the adverse impact of heavy metals (Cd²⁺, Cu²⁺, Cr₂O₇^2?) on PYR biodegradation remarkably. The sequencing analysis revealed that Methylobacterium, Burkholderia and Stenotrophomonas were the dominant genera of QY1 in almost all treatments, indicating that these genera might play key roles in PAHs biodegradation. Overall, this study provided new insights into the efficient bioremediation of PAHs-contaminated site.     

Isolation and characterization of a strain with high microbial attachment in aerobic granular sludge

Aerobic granule is a special microbial aggregate associated with biofilm structure. The formation of aerobic granular sludge is primarily depending on its bacterial community and relevant microbiological properties. In this experiment, a strain with high microbial attachment was isolated from aerobic granular sludge, and the detailed characteristics were examined. Its high attachment ability could reach 2.34 (OD_600nm), while other low attachment values were only around 0.06-0.32, which indicated a big variation among the different bacteria. The strain exhibited a very special morphology with many fibric fingers under SEM observation. A distinctive behaviour was to form a spherical particle by themselves, which would be very beneficial for the formation and development of granular sludge. The EPS measurement showed that its PN content was higher than low attachment bacteria, and 3D-EEM confirmed that there were some different components. Based on the 16S rRNA analysis, it was identified to mostly belong to Stenotrophomonas. Its augmentation to particle sludge cultivation demonstrated that the strain could significantly promote the formation of aerobic granule. Conclusively, it was strongly suggested that it might be used as a good and potential model strain or chassis organism for the aerobic granular sludge formation and development.     

Integration of microbial reductive dehalogenation with persulfate activation and oxidation (Bio-RD-PAO) for complete attenuation of organohalides

•Bio-RD-PAO can effectively and extensively remove organohalides. •Bio-RD alone effectively dehalogenate the highly-halogenated organohalides. •PAO alone is efficient in degrading the lowly-halogenated organohalides. •The impacts of PAO on organohalide-respiring microbial communities remain elusive. •Bio-RD-PAO provides a promising solution for remediation of organohalide pollution. Due to the toxicity of bioaccumulative organohalides to human beings and ecosystems, a variety of biotic and abiotic remediation methods have been developed to remove organohalides from contaminated environments. Bioremediation employing organohalide-respiring bacteria (OHRB)-mediated microbial reductive dehalogenation (Bio-RD) represents a cost-effective and environmentally friendly approach to attenuate highly-halogenated organohalides, specifically organohalides in soil, sediment and other anoxic environments. Nonetheless, many factors severely restrict the implications of OHRB-based bioremediation, including incomplete dehalogenation, low abundance of OHRB and consequent low dechlorination activity. Recently, the development of in situ chemical oxidation (ISCO) based on sulfate radicals (SO₄^·−) via the persulfate activation and oxidation (PAO) process has attracted tremendous research interest for the remediation of lowly-halogenated organohalides due to its following advantages, e.g., complete attenuation, high reactivity and no selectivity to organohalides. Therefore, integration of OHRB-mediated Bio-RD and subsequent PAO (Bio-RD-PAO) may provide a promising solution to the remediation of organohalides. In this review, we first provide an overview of current progress in Bio-RD and PAO and compare their limitations and advantages. We then critically discuss the integration of Bio-RD and PAO (Bio-RD-PAO) for complete attenuation of organohalides and its prospects for future remediation applications. Overall, Bio-RD-PAO opens up opportunities for complete attenuation and consequent effective in situ remediation of persistent organohalide pollution.     

Acid Orange 7 degradation using methane as the sole carbon source and electron donor

• AO7 degradation was coupled with anaerobic methane oxidation. • Higher concentration of AO7 inhibited the degradation. • The maximum removal rate of AO7 reached 280 mg/(L·d) in HfMBR. • ANME-2d dominated the microbial community in both batch reactor and HfMBR. • ANME-2d alone or synergistic with the partner bacteria played a significant role. Azo dyes are widely applied in the textile industry but are not entirely consumed during the dyeing process and can thus be discharged to the environment in wastewater. However, azo dyes can be degraded using various electron donors, and in this paper, Acid Orange 7 (AO7) degradation performance is investigated using methane (CH₄) as the sole electron donor. Methane has multiple sources and is readily available and inexpensive. Experiments using ¹³C-labeled isotopes showed that AO7 degradation was coupled with anaerobic oxidation of methane (AOM) and, subsequently, affected by the initial concentrations of AO7. Higher concentrations of AO7 could inhibit the activity of microorganisms, which was confirmed by the long-term performance of AO7 degradation, with maximum removal rates of 8.94 mg/(L·d) in a batch reactor and 280 mg/(L·d) in a hollow fiber membrane bioreactor (HfMBR). High-throughput sequencing using 16S rRNA genes showed that Candidatus Methanoperedens, affiliated to ANME-2d, dominated the microbial community in the batch reactor and HfMBR. Additionally, the relative abundance of Proteobacteria bacteria (Phenylobacterium, Pseudomonas, and Geothermobacter) improved after AO7 degradation. This outcome suggested that ANME-2d alone, or acting synergistically with partner bacteria, played a key role in the process of AO7 degradation coupled with AOM.