电解法处理活性染料废水的研究

某化工厂活性染料生产废水高CODCr值、高浓度、高色度、高盐分、成分复杂、有毒有害物质多、可生化性差。实验确定了废水经AS剂絮凝和电解预处理的研究方案。主要考察了电极极板材料、电解pH值、电解电压大小、电解时间和电极极板间距对CODCr去除效果的影响 ,从而确定了最佳电解条件 :采用石墨板电极 ,pH =3,电解电压 6 5V ,电解时间 5 0min ,电极极板间距 5cm。最佳条件下经放大实验 ,发现CODCr去除率高达 70 %以上。     

异丙醇与OH自由基和Cl反应产物的研究

在室温和一个大气压下 ,利用气相色谱和光离子色谱研究了空气中异丙醇与OH自由基和Cl的反应产物 .其主要产物为丙酮、乙醛和甲醛 .对于OH自由基与异丙醇的反应 ,丙酮与乙醛的产率分别大于 81 6%和 6 6% ;对于异丙醇与Cl的反应 ,丙酮和乙醛的产率分别为 78 5± 4 6%和 1 1 7± 1 0 % .结合光氧化反应主要产物 ,对异丙醇的光氧化反应机理进行了初步的探讨     

电化学法处理含盐染料废水

研究了电化学法处理含盐染料废水的可行性及其处理效果．结果表明,电化学法对废水的色度和COD具有良好的去除效果,电解过程中余氯的产生对色度和COD的去除有决定性作用．实验确定的高浓度含盐废水电化学处理条件为：电流密度0．017A/cm²,电压10．3V,平均电导率12．35ms/cm,电解60min,色度和COD的去除率分别为85％和99．8％．电解过程无难以继续反应的中间产物生成．     

聚醚废水处理工艺研究

研究了中和混凝-厌氧十好氧-生物活性炭组合工艺,在不同工况和运行参数条件下处理聚醚废水的效果．结果表明,中和混凝能有效地降低生物处理的污泥负荷,调节pH值6．7,聚合氯化铝的投加量为l00mg/L时．聚醚废水COD去除率可达28％,当进水的COD为3000～4000mg/L时,聚醚废水经此组合工艺处理后,COD的总去除率达96％以上,出水COD值约150mg/L.     

用活性白土为吸附剂处理含铬电镀废水的初步实验

论述了用活性白土为吸附剂,处理含铬电镀废水的最佳吸附条件：吸附剂的用量、吸附时间以及试液pH值对铬去除率的影响。做出了吸附等温线,并且对其吸附机理作了初步的探讨。另外指出了需进一步研究的问题。     

Kinetics of aniline oxidation with chlorine dioxide

For the first time, kinetics of aniline oxidation with chlorine dioxide(ClO2) were investigated systematically by detecting concentration of aniline with HPLC at regular intervals. Results showed that the reaction was first-order both in ClO2 and in aniline, and the oxidation reaction could be described as second-order reaction. Stoichiometric factor η was experimentally determined to be 2.44. The second-order-reaction rate constant k was 0.11L/(mol.s)under condition of pH 6.86 and water temperature(Tw) 287K. Reaction activation energy was 72.31 kJ/mol, indicating that the reaction could take place under usual water treatment conditions. The reaction rate constants in acidic and alkali media were greater than that in neutral medium. Chlorite ion could slightly increase reaction rate in acidic medium. p-aminophenol and azobenzene were detected by GC-MS as intermediates.     

酸性氯化铜蚀刻废液一步沉淀法制备碱式碳酸铜

以酸性氯化铜蚀刻废液为原料,在Na₂CO₃和助剂A存在下,采用一步沉淀法制备碱式碳酸铜。考察了反应pH、n（Na₂CO₃）∶n（助剂A）、反应时间和反应温度对碱式碳酸铜制备效果的影响,并采用XRD、TG 及SEM对产品进行了表征。实验结果表明：在反应pH 7.0、沉淀剂配比n（Na₂CO₃）∶n（助剂A）=1∶2、反应时间1.0 h、反应温度70 ℃的条件下,产品的w（Cu²⁺）达55.62%,w（Cl^-）为0.013%,符合HG/T 4825—2015《工业碱式碳酸铜》的要求;蚀刻废液中Cu²⁺的回收率接近100%。表征结果表明,制得的产品为单一组分CuCO₃·Cu（OH）₂,小颗粒为直径1.8~5.4 μm的不规则球形,团聚后的大颗粒呈姜块状形貌,粒径为48~75 μm。     

冬季不同污水处理工艺对溶解性有机物的去除

以东北地区4个城市污水处理厂为研究对象,考察冬季不同污水处理工艺对溶解性有机物(DOM)组分的去除效果,以及对DOM组分的光谱学特性和卤代活性的影响.利用XAD树脂将DOM分为5个部分:疏水性有机酸(HPO-A)、疏水性中性有机物(HPO-N)、过渡亲水性有机酸(TPI-A)、过渡亲水性中性有机物(TPI-N)和亲水性有机物(HPI).结果表明,A/O法、曝气生物滤池、浮动填料法和A2/O法对DOM都具有较高的去除能力,其中曝气生物滤池对DOM的处理效果最好.经4种污水处理工艺处理后,5种组分的芳香性和三卤甲烷生成活性(STHMFP)均升高.A2/O法对HPO-A和TPI-A的芳香性增强程度最高,而曝气生物滤池对HPO-N,TPI-N和HPI的芳香性增强程度最高.浮动填料法对HPO-A,TPI-A和HPI的STHMFP升高最显著,A2/O法对HPO-N的STHMFP增加最显著,曝气生物滤池对TPI-N的STHMFP升高最显著.4种污水处理工艺对HPI中荧光物质的去除率高于非荧光物质.而对于其他4种DOM组分来说,不同的污水处理工艺对不同荧光峰的改变不相同.     

Treatment,residual chlorine and season as factors affecting variability of trihalomethanes in small drinking water systems

Seasonal variability in source water can lead to challenges for drinking water providers related to operational optimization and process control in treatment facilities. The objective of this study is to investigate seasonal variability of water quality in municipal small water systems (<3000 residents) supplied by surface waters. Residual chlorine and trihalomethanes (THM) were measured over seven years (2003–2009). Comparisons are made within each system over time, as well as between systems according to the type of their treatment technologies. THM concentrations are generally higher in the summer and autumn. The seasonal variability was generally more pronounced in systems using chlorination plus additional treatment. Chloroform, total THM (TTHM) and residual chlorine concentrations were generally lower in systems using chlorination plus additional treatment. Conversely, brominated THM concentrations were higher in systems using additional treatment. Residual chlorine was highest in the winter and lowest in the spring and summer. Seasonal variations were most pronounced for residual chlorine in systems with additional treatment. There was generally poor correlation between THM concentrations and concentrations of residual chlorine. Further study with these data will be beneficial in finding determinants and indicators for both quantity and variability of disinfection byproducts and other water quality parameters.     

塑料管材输配水过程中有机物释放规律研究

研究了目前给水管网中常用的3种塑料管材,未增塑聚氯乙烯(uPVC),聚乙烯(PE)和无规共聚聚丙烯(PPR)管在输配水过程中有机物的释放规律.通过静态管段实验模拟给水管网中不同输配水状态,选取总有机碳(TOC)为综合评价指标,考察了不同塑料管材中有机物随时间的迁移释放特性,并分析了管材有机物释放对管网水中余氯消耗的影响.随着管材输配水次数的增加,uPVC管释放至水中的TOC浓度和TOC释放速率分别在0.03mg/L和0.04μg/(d?cm2)以下,而PE管和PPR管在输配水过程中TOC的释放浓度和释放速率在初期最大[PE: 0.19mg/L,0.25μg/(d?cm2);PPR:0.07mg/L,0.09μg/(d?cm2)],且后期递减并趋于平稳[PE:0.03~0.08mg/L,0.05~0.10μg/(d?cm2);PPR:0.01~0.03mg/L, 0.01~0.04μg/(d?cm2)].随着水力停留时间的增加,不同管材释放的有机物浓度持续升高.不同管材有机物的释放能力排序为:PE>PPR>uPVC.各管材的有机物释放特性直接影响管网水的余氯消耗特性,且管材的有机物释放量越多,管网水的余氯消耗越快.PE管的使用易引起水体有机污染问题.本研究明确了3种常用塑料管材的有机物释放规律,将进一步为与塑料管材安全性能评价相关的国家标准的修订提供理论依据.