城市表层土壤重金属污染分析研究

根据某城市土壤表层中的8种重金属Cu、Pb、Cd、Hg、As、Cr、Ni、Zn的浓度数据,利用地统计学原理方法,研究了不同功能区土壤重金属的污染特征。结果表明Cd、Cu、Hg、Pb和Zn在工业区和主干道路区浓度超标,并且这几种元素的富集系数偏高,说明污染来源主要是工业生产、汽车尾气排放及汽车轮胎磨损等。此研究对城市土壤重金属污染治理及修复、重金属污染重点行业污染控制等提供参考。     

DTRO膜在垃圾渗滤液处理中的应用

文章介绍了DTRO膜独特的结构及特点,通过结合工程实例及运行数据,论述了DTRO膜的处理工艺以及对污染物显著的去除效果。     

膜生物反应器(MBR)运行及节能分析

污水处理中会出现污泥膨胀的情况,污泥膨胀导致出水水质变差。本文通过实验研究了污泥膨胀时膜生物反应器的膜污染影响因素及降低膜生物反应器节约能耗对策。     

亚微米气溶胶高效过滤装置的设计

针对亚微米气溶胶颗粒进入大气中危害环境及人类的健康的问题,设计了一种移动式亚微米气溶胶高效过滤装置,采用最易穿透粒径法(MPPS)测试了装置的过滤效率,结果表明:该装置具有较高的过滤效率,在0.1~0.25μm粒径范围内,装置的过滤效率在99.999%以上,该设备可用于亚微米气溶胶颗粒的过滤净化。     

曝气强度对膜生物反应器处理石化废水工艺运行特征的影响

采用膜生物反应器(Membrane Bioreactor,MBR)处理石化废水,研究曝气强度分别为1.50,3.00 m3/(m2·h)的条件下,MBR对石化废水中主要污染物的去除特征、跨膜压差(Trans Membrane Pressure,TMP)和混合液性质的变化特征。结果表明:在两种曝气强度条件下MBR对COD、NH+4-N及挥发酚等污染物的平均去除率分别为80.74%、80.23%、96.79%和97.55%、99.34%、98.84%,即在不同曝气条件下,曝气强度的变化对MBR的污染物去除性能无显著影响。但随着曝气强度由1.50 m3/(m2·h)增加到3.00 m3/(m2·h),MBR达到设定的最大跨膜压差(TMPMax=25k Pa)的运行时间由11.8 d增加到31.4 d,TMP上升速率降低。通过活性污泥颗粒粒径分析发现:增加曝气强度后,对膜污染影响显著的活性污泥颗粒粒径范围(0~2μm)所占体积比由2.10%减小到1.78%;并且混合液中溶解性微生物产物(soluble microbial product,SMP)和胞外聚合物(extracellular polymeric substance,EPS)质量浓度分别由24.07 mg/L和15.66 mg/g减小到15.14 mg/L和9.81 mg/g,从而降低了膜污染速率。     

MBR出水后置化学除磷研究

选用不同的化学除磷药剂及固液分离方式,针对膜生物反应器出水进行后置化学除磷静态试验研究。试验表明,在MBR出水平均浓度为(6.0±0.3)mg/L时,在化学药剂的最佳投药量和混凝时间的条件下,TP可以稳定达到一级A标准,去除率达到95%以上;滤液达一级A标准,氯化铝、氯化铁、聚合硫酸铁、硫酸铝最佳投加量为1.5 mol/mol,硫酸铁、聚合硫酸铝最佳投加量为3.0 mol/mol,最佳混凝时间均为10 min;滤纸和滤膜可以有效分离混凝混合液中的TP,滤液TP可稳定达一级A标准,而微网对混合液中粒径小于D10的颗粒无法分离,致使滤液TP无法达标;PAM投加后,絮体粒径显著增大,固液分离效果也相应增强。微网分离效果较投加前有了明显提高,滤液TP可稳定达到一级B标准。     

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium nanoparticles

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium （Pd） nanoparticles was studied for the first time. The effects of Pd loading, dye concentration and reuse repetitions of membranes were investigated. In reduction, the dye concentration decreased whereas the pH rose gradually. An optimal Pd loading was found. The catalytic membranes were able to be reused more than 3 times.     

Fouling distribution in forward osmosis membrane process

Fouling behavior along the length of membrane module was systematically investigated by performing simple modeling and lab-scale experiments of forward osmosis （FO） membrane process. The flux distribution model developed in this study showed a good agreement with experimental results, validating the robustness of the model. This model demonstrated, as expected, that the permeate flux decreased along the membrane channel due to decreasing osmotic pressure differential across the FO membrane. A series of fouling experiments were conducted under the draw and feed solutions at various recoveries simulated by the model. The simulated fouling experiments revealed that higher organic （alginate） fouling and thus more flux decline were observed at the last section of a membrane channel, as foulants in feed solution became more concentrated. Furthermore, the water flux in FO process declined more severely as the recovery increased due to more foulants transported to membrane surface with elevated solute concentrations at higher recovery, which created favorable solution environments for organic adsorption. The fouling reversibility also decreased at the last section of the membrane channel, suggesting that fouling distribution on FO membrane along the module should be carefully examined to improve overall cleaning efficiency. Lastly, it was found that such fouling distribution observed with co-current flow operation became less pronounced in counter- current flow operation of FO membrane process.     

Inhibitory effects of nisin-coated multi-walled carbon nanotube sheet on biofilm formation from Bacillus anthracis spores

Multi-walled carbon nanotube（MWCNT） sheet was fabricated from a drawable MWCNT forest and then deposited on poly（methyl methacrylate） film. The film was further coated with a natural antimicrobial peptide nisin. We studied the effects of nisin coating on the attachment of Bacillus anthracis spores, the germination of attached spores, and the subsequent biofilm formation from attached spores. It was found that the strong adsorptivity and the super hydrophobicity of MWCNTs provided an ideal platform for nisin coating. Nisin coating on MWCNT sheets decreased surface hydrophobicity, reduced spore attachment, and reduced the germination of attached spores by 3.5 fold, and further inhibited the subsequent biofilm formation by 94.6% compared to that on uncoated MWCNT sheet. Nisin also changed the morphology of vegetative cells in the formed biofilm.The results of this study demonstrated that the anti-adhesion and antimicrobial effect of nisin in combination with the physical properties of carbon nanotubes had the potential in producing effective anti-biofilm formation surfaces.     

新型IC反应器在山梨醇废水处理中的工程应用

将布水装置优化后的新型内循环(IC)反应器应用于某山梨醇生产企业实际废水的二级厌氧生化处理,获得了较好的处理效果。调试阶段的结果表明:经过IC反应器的处理后,废水COD浓度由处理前的2 374~4 967 mg/L降至301~823 mg/L,COD去除率达81.4%~91.2%,COD容积负荷达8.1~13.7 kg/(m3·d);总体来说,当水力负荷增大时,COD容积负荷也相应增大;IC反应器的出水挥发性脂肪酸(VFA)基本控制在200 mg/L以下;厌氧出水再依次经过接触氧化池和絮凝沉淀池等配套工艺的处理后,COD降至80 mg/L以下,实现达标排放。