DTRO膜在垃圾渗滤液处理中的应用

文章介绍了DTRO膜独特的结构及特点,通过结合工程实例及运行数据,论述了DTRO膜的处理工艺以及对污染物显著的去除效果。     

膜生物反应器(MBR)运行及节能分析

污水处理中会出现污泥膨胀的情况,污泥膨胀导致出水水质变差。本文通过实验研究了污泥膨胀时膜生物反应器的膜污染影响因素及降低膜生物反应器节约能耗对策。     

曝气强度对膜生物反应器处理石化废水工艺运行特征的影响

采用膜生物反应器(Membrane Bioreactor,MBR)处理石化废水,研究曝气强度分别为1.50,3.00 m3/(m2·h)的条件下,MBR对石化废水中主要污染物的去除特征、跨膜压差(Trans Membrane Pressure,TMP)和混合液性质的变化特征。结果表明:在两种曝气强度条件下MBR对COD、NH+4-N及挥发酚等污染物的平均去除率分别为80.74%、80.23%、96.79%和97.55%、99.34%、98.84%,即在不同曝气条件下,曝气强度的变化对MBR的污染物去除性能无显著影响。但随着曝气强度由1.50 m3/(m2·h)增加到3.00 m3/(m2·h),MBR达到设定的最大跨膜压差(TMPMax=25k Pa)的运行时间由11.8 d增加到31.4 d,TMP上升速率降低。通过活性污泥颗粒粒径分析发现:增加曝气强度后,对膜污染影响显著的活性污泥颗粒粒径范围(0~2μm)所占体积比由2.10%减小到1.78%;并且混合液中溶解性微生物产物(soluble microbial product,SMP)和胞外聚合物(extracellular polymeric substance,EPS)质量浓度分别由24.07 mg/L和15.66 mg/g减小到15.14 mg/L和9.81 mg/g,从而降低了膜污染速率。     

MBR出水后置化学除磷研究

选用不同的化学除磷药剂及固液分离方式,针对膜生物反应器出水进行后置化学除磷静态试验研究。试验表明,在MBR出水平均浓度为(6.0±0.3)mg/L时,在化学药剂的最佳投药量和混凝时间的条件下,TP可以稳定达到一级A标准,去除率达到95%以上;滤液达一级A标准,氯化铝、氯化铁、聚合硫酸铁、硫酸铝最佳投加量为1.5 mol/mol,硫酸铁、聚合硫酸铝最佳投加量为3.0 mol/mol,最佳混凝时间均为10 min;滤纸和滤膜可以有效分离混凝混合液中的TP,滤液TP可稳定达一级A标准,而微网对混合液中粒径小于D10的颗粒无法分离,致使滤液TP无法达标;PAM投加后,絮体粒径显著增大,固液分离效果也相应增强。微网分离效果较投加前有了明显提高,滤液TP可稳定达到一级B标准。     

Photocatalytic activity of Fe-doped CaTiO3 under UV-visible light

The photocatalytic degradation of methylene blue（MB） over Fe-doped CaTiO3 under UV-visible light was investigated. The as-prepared samples were characterized using X-ray diffraction（XRD）, scanning electron microscope（SEM） equipped with an energy dispersive spectrometer（EDS） system, Fourier transform infrared spectra（FT-IR）, and UV-visible diffuse reflectance spectroscopy（DRS）. The results show that the doping with Fe significantly promoted the light absorption ability of CaTiO3 in the visible light region. The Fe-doped CaTiO3 exhibited higher photocatalytic activity than CaTiO3 for the degradation of MB.However, the photocatalytic activity of the Fe-doped CaTiO3 was greatly influenced by the calcination temperature during the preparation process. The Fe-doped CaTiO3 prepared at500°C exhibited the best photocatalytic activity, with degradation of almost 100% MB（10 ppm）under UV-visible light for 180 min.     

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium nanoparticles

Catalytic bubble-free hydrogenation reduction of azo dye by porous membranes loaded with palladium （Pd） nanoparticles was studied for the first time. The effects of Pd loading, dye concentration and reuse repetitions of membranes were investigated. In reduction, the dye concentration decreased whereas the pH rose gradually. An optimal Pd loading was found. The catalytic membranes were able to be reused more than 3 times.     

Fouling distribution in forward osmosis membrane process

Fouling behavior along the length of membrane module was systematically investigated by performing simple modeling and lab-scale experiments of forward osmosis （FO） membrane process. The flux distribution model developed in this study showed a good agreement with experimental results, validating the robustness of the model. This model demonstrated, as expected, that the permeate flux decreased along the membrane channel due to decreasing osmotic pressure differential across the FO membrane. A series of fouling experiments were conducted under the draw and feed solutions at various recoveries simulated by the model. The simulated fouling experiments revealed that higher organic （alginate） fouling and thus more flux decline were observed at the last section of a membrane channel, as foulants in feed solution became more concentrated. Furthermore, the water flux in FO process declined more severely as the recovery increased due to more foulants transported to membrane surface with elevated solute concentrations at higher recovery, which created favorable solution environments for organic adsorption. The fouling reversibility also decreased at the last section of the membrane channel, suggesting that fouling distribution on FO membrane along the module should be carefully examined to improve overall cleaning efficiency. Lastly, it was found that such fouling distribution observed with co-current flow operation became less pronounced in counter- current flow operation of FO membrane process.     

Debromination of decabromodiphenyl ether by organo-montmorillonite-supported nanoscale zero-valent iron：Preparation, characterization and influence factors

An organo-montmorillonite-supported nanoscale zero-valent iron material(M-NZVI) was synthesized to degrade decabromodiphenyl ether(BDE-209). The results showed that nanoscale zero-valent iron had good dispersion on organo-montmorillonite and was present as a core-shell structure with a particle size range of nanoscale iron between 30–90 nm, characterized by XRD, SEM, TEM, XRF, ICP-AES, and XPS. The results of the degradation of BDE-209 by M-NZVI showed that the efficiency of M-NZVI in removing BDE-209 was much higher than that of NZVI. The efficiency of M-NZVI in removing BDE-209 decreased as the pH and the initial dissolved oxygen content of the reaction solution increased, but increased as the proportion of water in the reaction solution increased.     

Inhibitory effects of nisin-coated multi-walled carbon nanotube sheet on biofilm formation from Bacillus anthracis spores

Multi-walled carbon nanotube（MWCNT） sheet was fabricated from a drawable MWCNT forest and then deposited on poly（methyl methacrylate） film. The film was further coated with a natural antimicrobial peptide nisin. We studied the effects of nisin coating on the attachment of Bacillus anthracis spores, the germination of attached spores, and the subsequent biofilm formation from attached spores. It was found that the strong adsorptivity and the super hydrophobicity of MWCNTs provided an ideal platform for nisin coating. Nisin coating on MWCNT sheets decreased surface hydrophobicity, reduced spore attachment, and reduced the germination of attached spores by 3.5 fold, and further inhibited the subsequent biofilm formation by 94.6% compared to that on uncoated MWCNT sheet. Nisin also changed the morphology of vegetative cells in the formed biofilm.The results of this study demonstrated that the anti-adhesion and antimicrobial effect of nisin in combination with the physical properties of carbon nanotubes had the potential in producing effective anti-biofilm formation surfaces.     

铁碳微电解法预处理聚氯乙烯(PVC)离心母液废水

采用铁碳微电解法对聚氯乙烯(PVC)离心母液废水进行预处理。分别考察反应时间、铁粉投加量、Fe/C(质量比)、pH值及曝气速率对母液废水中的COD和聚乙烯醇(PVA)去除率的影响,并在此基础上通过正交实验确定了废水COD的最佳处理条件。结果表明,最佳处理条件为:反应时间为4 h、铁粉投加量为30 g/L、Fe/C为1:2、pH值为2、曝气速率为0.8 L/min。在该条件下,废水中COD、PVA和TOC的平均去除率分别为(67%±2)%、(98%±1)%和(55%±3)%,废水的BOD/COD值从0.3提高到0.5,可生化性得到了显著提高。同时,废水中的NH3-N、浊度也在很大程度上得到了去除,出水中总铁含量也很低。