利用FOCMEC和CAP方法反演2021年大丰海域M5.0及天宁M4.2地震震源机制解∗

利用 FOCMEC 和 CAP 方法分别对大丰海域 M5.0 地震、天宁 M4.2 地震震源机制解进行反演,分析两种方法所得结果的差异。大丰海域 M5.0 地震 FOCMEC 方法与 CAP 方法计算震源机制解结果存在细微差异,CAP 方法所得结果与其它机构结果较为统一。天宁 M4.2 地震 FOCMEC 方法与 CAP 方法计算震源机制解结果基本一致。 通过研究发现 CAP 方法对台站分布要求不高,但需要地震震级较大,波形信噪比高,震相拟合度较好;FOCMEC 方法对地震震级要求不高,但需要震中位置被台站包围较好,且震中附近台站密度较高,P 波初动清晰。     

Properties of Pyrolytic Chars and Activated Carbons Derived from Pilot-Scale Pyrolysis of Used Tires

Abstract

Used tires were pyrolyzed in a pilot-scale quasi-inert rotary kiln. Influences of variables, such as time, temperature, and agent flow, on the activation of obtained char were subsequently investigated in a laboratory-scale fixed bed. Meso-porous pores are found to be dominant in the pore structures of raw char. Brunauer-Emmett-Teller (BET) surfaces of activated chars increased linearly with carbon burnoff. The carbon burnoff of tire char achieved by carbon dioxide (CO₂) under otherwise identical conditions was on average 75% of that achieved by steam, but their BET surfaces are almost the same. The proper activation greatly improved the aqueous adsorption of raw char, especially for small molecular adsorbates, for example, phenol from 6 to 51 mg/g. With increasing burnoff, phenol adsorption exhibited a first-stage linear increase followed by a rapid drop after 30% burnoff. Similarly, iodine adsorption first increased linearly, but it held as the burnoff exceeded 40%, which implied that the reduction of iodine adsorption due to decreasing micro-pores was partially made up by increasing mesopores. Both raw chars and activated chars showed appreciable adsorption capacity of methylene-blue comparable with that of commercial carbons. Thus, tire-derived activated carbons can be used as an excellent mesoporous adsorbent for larger molecular species.     

中美环境监测体制之比较

对中美环境监测体制进行对比性评述,指出了中国环境监测行业存在的分析标准滞后、体制不完善、人员匮乏等问题,提出借鉴美国经验,完善法律体系,引入市场机制,逐步培育竞争有序、监管到位的环境监测行业的建议。     

城市天然气管道风险特征与肯特法的改进

根据城市高压天然气管道特点,将适合于城市天然气管道风险分析的肯特评分法加以改进,包括调整评分项目和事故因素权重,使其成为适于城市天然气管道的风险分析法。将改进后的肯特评分法应用于常州21km高压天然气管道的风险评价,得出8个相对高风险管段,其分析结果可作为安全管理人员合理分配维护资源的理论依据。工程应用实例证明:改进后的肯特法具有较强的可行性,是城市高压天然气管道风险评估的有效工具。     

Diversity of methanotrophs in a simulated modified biocover reactor

A simulated landfill biocover microcosm consisting of a modifying ceramsite material and compost were investigated. Results show that the mixture can improve the material porosity and achieve a stable and highly efficient (100%) methane oxidation over an extended operating period. The diversity of the methanotrophic community in the microcosm was assessed. Type I methanotrophs were enhanced in the microcosm due to the increased air diffusion and distribution, whereas the microbial diversity and population density of type II methanotrophs were not significantly affected. Moreover, the type I methanotrophic community structure significantly varied with the reactor height, whereas that of type II methanotrophic communities did not exhibit a spatial variation. Phylogenetic analysis showed that type I methanotroph-based nested polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) resulted in the detection of eight different populations, most of which are related to Methylobacter sp., whereas that of type II resulted in the detection of nine different populations, most of which are related to Methylocystaceae. Methanotrophic community analysis also indicated that a number of new methanotrophic genera not closely related to any known methanotrophic populations were present.     

人工湿地系统植被构建方式探讨

植物是人工湿地系统的核心之一,不但有助于污水净化,还能产生一定的生态环境效益.湿地运行初期植物的生长好坏直接影响到今后植物的生长和污染物的去除效率.面对新建的人工湿地,如何快速高效的构建植被系统,是工程建设中必须面对的一个重要问题.湿地植被构建方式的改进有助于提高湿地建设效率,改善系统处理效果.本文从工程角度探讨植物种植方式、种植时间、种植密度及湿地启动对湿地植被构建的影响.     

Evaluation of the emission characteristics of PCDD/Fs from electric arc furnaces

Distribution of PCDD/F (polychlorinated dibenzo-p-dioxin and polychlorinated dibenzofuran) congeners at two electric arc furnaces (EAFs) in Taiwan is evaluated via intensive stack sampling and analysis. Two kinds of exhaust system in EAFs including stack system and shutter system are selected for measuring dioxin emissions. In addition, dioxin emissions during oxidation and reduction stages at EAF-A were characterized. Results indicate that the PCDD/F concentration of stack gas in EAF-A was 4.39 ng/N m³ while total Toxic Equivalent Quantity (TEQ) concentration was 0.35 ng I-TEQ/N m³. The PCDD/F concentration of stack gas in EAF-B was 2.20 ng/N m³ and the TEQ concentration was 0.14 ng I-TEQ/N m³. 1,2,3,4,6,7,8-H_pCDF, OCDD and OCDF are the major contributors of the dioxin concentrations for two EAFs investigated and the percentage of PCDD/F in particulate phase increases as the chlorination level of the PCDD/F congener increases. The results obtained on gas/particulate partitioning of PCDD/Fs in flue gases prior to the APCD in EAFs indicate that more than 90% exists in particulate phase. In EAF-A, the PCDD/F concentration during oxidation stage is slightly higher than that measured during reduction stage, including the sampling points of CO converter outlet, prior to bag filter and stack. Majority of PCDD/Fs emitted from steel-making processes exists in particulate-phase (about 60–70%) at both EAFs investigated.     

Partitioning and removal of dioxin-like congeners in flue gases treated with activated carbon adsorption

Activated carbon adsorption is commonly used to control dioxin-like congener (PCDD/Fs and PCBs) emissions. Partitioning of PCDD/Fs and PCBs between vapor and solid phases and their removal efficiencies achieved with existing air pollution control devices (APCDs) at a large-scale municipal waste incinerator (MWI) and an industrial waste incinerator (IWI) are evaluated via intensive stack sampling and analysis. Those two facilities investigated are equipped with activated carbon injection (ACI) with bag filter (BF) and fixed activated carbon bed (FACB) as major PCDD/F control devices, respectively. Average PCDD/F and PCB concentrations of stack gas with ACI+BF as APCDs are 0.031 and 0.006ng-TEQ/Nm(3), and that achieved with FACB are 1.74 and 0.19ng-TEQ/Nm(3) in MWI and IWI, respectively. The results show that FACB could reduce vapor-phase PCDD/Fs and PCBs concentrations in flue gas, while the ACI+BF can effectively adsorb the vapor-phase dioxin-like congener and collect the solid-phase PCDD/Fs and PCBs in the meantime. Additionally, the results of the pilot-scale adsorption system (PAS) experimentation indicate that each gram activated carbon adsorbs 105-115ng-PCDD/Fs and each surface area (m(2)) of activated carbon adsorbs 10-25ng-PCDD/Fs. Based on the results of PAS experimentation, this study confirms that the surface area of mesopore+macropore (20-200A) of the activated carbon is a critical factor affecting PCDD/F adsorption capacity.     

Thermal hazard accident investigation of hydrogen peroxide mixing with propanone employing calorimetric approaches

Hydrogen peroxide (H₂O₂), historically, due to its broad applications in the chemical industries, has caused many serious fires and explosions around the world. Its thermal hazards may also be incurred by an incompatible reaction with other chemicals, and a runaway reaction may be induced in the last stage. This study applied thermal analytical methods to explore the H₂O₂ leading to these accidents by incompatibility and to discuss what might be formed by the upset situations. Thermal hazard analysis contained a solvent, propanone (CH₃COCH₃, so-called acetone), which was deliberately selected to mix with H₂O₂ for investigating the degree of thermal hazard. Differential scanning calorimetry (DSC) and vent sizing package 2 (VSP2) were employed to evaluate the thermal hazard of H₂O₂. The results indicated that H₂O₂ is highly hazardous while mixed with propanone, as a potential contaminant. The time to maximum rate (TMR) was used as emergency response time in the chemical industries. Therefore, TMR of H₂O₂ was calculated to be 70 min for runaway reaction (after T₀) and TMR of H₂O₂/propanone was discovered to be 27 min only. Fire and explosion hazards could be successfully lessened if the safety-related data are properly imbedded into manufacturing processes.     

GB/T 7702-2008《煤质颗粒活性炭试验方法》标准的研究

通过对GB/T 7702-2008《煤质颗粒活性炭试验方法》的修订,研究了国际上先进国家的ASTM、JIS、ГОСТ同类标准内容。本系列标准除等同采用部分国际先进标准外,还结合本国特点增加了部分国外标准没有的内容,同时着重对碘吸附值测定进行了深入研究,确定了国际先进的碘吸附值试验方法。